Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.
Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: This paper deals with the problem of thermal and
mechanical shocks, which rising during operation, mostly at
interrupted cut. Here will be solved their impact on the cutting edge
tool life, the impact of coating technology on resistance to shocks
and experimental determination of tool life in heating flame.
Resistance of removable cutting edges against thermal and
mechanical shock is an important indicator of quality as well as its
abrasion resistance. Breach of the edge or its crumble may occur due
to cyclic loading. We can observe it not only during the interrupted
cutting (milling, turning areas abandoned hole or slot), but also in
continuous cutting. This is due to the volatility of cutting force on
cutting. Frequency of the volatility in this case depends on the type
of rising chips (chip size element). For difficult-to-machine materials
such as austenitic steel particularly happened at higher cutting speeds
for the localization of plastic deformation in the shear plane and for
the inception of separate elements substantially continuous chips.
This leads to variations of cutting forces substantially greater than for
other types of steel.
Abstract: This paper deals with the status of solid waste pollution in touristic spots of North coastal Andhra Pradesh. Case studies of Eco tourism, cultural tourism and pilgrim tourism are elaborately discussed and the study is based on both primary and secondary data. Data collection includes field collection of solid waste, semi structured interviews and observation of tourists. Results indicate generation of 72% Non biodegradable material in Eco touristic places like RK beach Visakhapatnam, Araku Valley. Pydithalli Jathra is a famous cultural touristic attraction and more than one lakh people converge here. The solid waste at this spot includes 20% coconut shells, 50% plastic bottles and covers, 20% Banana peelings and remaining are food materials. Radhasapthami is the most important festival celebrated at famous sun temple Arasavalli of Srikakulam. Here solid waste includes 50% water bottles, plastic covers, 10% papers, 10% hair, 30% left out food material and Banana peelings.
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: Principally, plants grown in soilless culture may be
attacked by the same pests and diseases as cultivated traditionally in
soil. The most destructive phytopathogens are fungi, such as
Phythium, Phytophthora and Fusarium, followed by viruses, bacteria
and nematodes. We investigated effect of carbon nanotube filters on
disease management of soilless culture. Tomato seedlings transplant
in plastic pots filled with a soilless media of vermiculite. The crop
irrigated and fertilized using a hydroponic nutrient solution. We used
carbon nanotube filters for nutrient solution disinfection. Our results
show that carbon nanotube filtration significantly reduces pathogens
on tomato plants. Fungal elimination (Fusarium oxysporum and
Pythium spp.) was usually successful at about 96 to 99.9% all over
the cultural season. It is seem that in tomato soilless culture,
nanofiltration constitutes a reliable method that allows control of the
development of diseases caused by pathogenic fungi
Abstract: The measurements of 226Ra, 232Th and 40K using
gamma spectrometry and radon concentration and exhalation rates
measurements using solid state nuclear track (LR-115, Type-II
plastic) detectors are used to asses a first order exposure risk for the
persons residing in Fatehbad and Hissar districts of Western Haryana,
India. The concentration of Radium, Thorium and Potassium in the
soil samples varies from 13.37 Bq m-3 to 24.67 Bq m-3, 34.67 Bq m-3
to 67.34 Bq m-3 and 298.78 Bq m-3 to 405.67 Bq m-3 respectively
with average values of 18.78, 47.35 and 361.57 Bq m-3 respectively.
The radium equivalent activity (Raeq) calculated for the same soil
samples varies from 92.72 Bq m-3 to 140.6 Bq m-3 with an average
value of 111.80 Bq m-3. The values of absorbed dose and annual
effective dose (indoors and outdoors) are found to vary from 44.18
nGy h-1 to 65.23 nGy h-1, 0.22 mSv y-1 to 0.32 mSv y-1 and 0.05 mSv
y-1 to 0.08 mSv y-1 respectively. The radon concentration and
exhalation rates have also been reported. The radium equivalent
activities in all the soil samples were found to be lower than the limit
(370 Bq kg-1) set in the Organization for Economic Cooperation and
Development (OECD) report and the value of Hex in all the samples
is less than unity.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: Friction-stir welding has received a huge interest in the last few years. The many advantages of this promising process have led researchers to present different theoretical and experimental explanation of the process. The way to quantitatively and qualitatively control the different parameters of the friction-stir welding process has not been paved. In this study, a refined energybased model that estimates the energy generated due to friction and plastic deformation is presented. The effect of the plastic deformation at low energy levels is significant and hence a scale factor is introduced to control its effect. The predicted heat energy and the obtained maximum temperature using our model are compared to the theoretical and experimental results available in the literature and a good agreement is obtained. The model is applied to AA6000 and AA7000 series.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: An investigation of the process of deformation hardening and evolution of deformation defect medium in dispersion-hardened materials with face centered cubic matrices and nanoparticles was done. Mathematical model including balance equation for the deformation defects was used.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.
Abstract: Municipal solid waste (MSW) comprises of a wide
range of heterogeneous materials generated by individual, household
or organization and may include food waste, garden wastes, papers,
textiles, rubbers, plastics, glass, ceramics, metals, wood wastes,
construction wastes but it is not limited to the above mentioned
fractions. The most common Municipal Solid Waste pretreatment
method in use is thermal pretreatment (incineration) and Mechanical
Biological pretreatment. This paper presents an overview of these
two pretreatment methods describing their benefits and laboratory
scale reactors that simulate landfill conditions were constructed in
order to compare emissions in terms of biogas production and
leachate contamination between untreated Municipal Solid Waste and
Mechanical Biological Pretreated waste. The findings of this study
showed that Mechanical Biological pretreatment of waste reduces the
emission level of waste and the benefit over the landfilling of
untreated waste is significant.