Abstract: The paper presents an innovative networked radar
system for detection of obstacles in a railway level crossing scenario.
This Monitoring System (MS) is able to detect moving or still
obstacles within the railway level crossing area automatically,
avoiding the need of human presence for surveillance. The MS is also
connected to the National Railway Information and Signaling System
to communicate in real-time the level crossing status. The
architecture is compliant with the highest Safety Integrity Level
(SIL4) of the CENELEC standard. The number of radar sensors used
is configurable at set-up time and depends on how large the level
crossing area can be. At least two sensors are expected and up four
can be used for larger areas. The whole processing chain that
elaborates the output sensor signals, as well as the communication
interface, is fully-digital, was designed in VHDL code and
implemented onto a Xilinx Virtex 6.
Abstract: Rural tourism is usually associated with rural
development because it has strong linkages to rural resources; but it
remains underdeveloped compared to urban tourism. This
underdevelopment of rural tourism serves as a motivation for this
study whose aim is to examine the factors affecting the perceived
satisfaction of rural tourists. The objectives of this study are: to
identify and design theories and models on rural tourism satisfaction,
and to empirically validate these models and theories through a
survey of tourists from the Malealea Lodge which is located in the
Mafeteng District, in the Mountain Kingdom of Lesotho. Data
generated by the collection of questionnaires used by this survey was
analyzed quantitatively using descriptive statistics and correlations in
SPSS after checking the validity and the reliability of the
questionnaire. The main hypothesis behind this study is the
relationship between the demographics of rural tourists, their
motivation, and their satisfaction, as supported by existing literature;
except that motivation is measured in this study according to three
dimensions: push factors, pull factors, and perceived usefulness of
ICTs in the rural tourism experience. Findings from this study
indicate that among the demographics factors, continent of origin and
marital status influence the satisfaction of rural tourists; and their
occupation affects their perceptions on the use of ICTs in rural
tourism. Moreover, only pull factors were found to influence the
satisfaction of rural tourists.
Abstract: Dengue outbreaks are affected by biological,
ecological, socio-economic and demographic factors that vary over
time and space. These factors have been examined separately and still
require systematic clarification. The present study aimed to investigate
the spatial-temporal clustering relationships between these factors and
dengue outbreaks in the northern region of Sri Lanka. Remote sensing
(RS) data gathered from a plurality of satellites were used to develop
an index comprising rainfall, humidity and temperature data. RS data
gathered by ALOS/AVNIR-2 were used to detect urbanization, and a
digital land cover map was used to extract land cover information.
Other data on relevant factors and dengue outbreaks were collected
through institutions and extant databases. The analyzed RS data and
databases were integrated into geographic information systems,
enabling temporal analysis, spatial statistical analysis and space-time
clustering analysis. Our present results showed that increases in the
number of the combination of ecological factor and socio-economic
and demographic factors with above the average or the presence
contribute to significantly high rates of space-time dengue clusters.
Abstract: The aim of this paper is to understand emerging
learning conditions, when a visual analytics is implemented and used
in K 12 (education). To date, little attention has been paid to the role
visual analytics (digital media and technology that highlight visual
data communication in order to support analytical tasks) can play in
education, and to the extent to which these tools can process
actionable data for young students. This study was conducted in three
public K 12 schools, in four social science classes with students aged
10 to 13 years, over a period of two to four weeks at each school.
Empirical data were generated using video observations and analyzed
with help of metaphors within Actor-network theory (ANT). The
learning conditions are found to be distinguished by broad
complexity, characterized by four dimensions. These emerge from
the actors’ deeply intertwined relations in the activities. The paper
argues in relation to the found dimensions that novel approaches to
teaching and learning could benefit students’ knowledge building as
they work with visual analytics, analyzing visualized data.
Abstract: Teaching art by digital means is a big challenge for
the majority of teachers of art and design in primary schools, yet it
allows relationships between art, technology and creativity to be
clearly identified. The aim of this article is to present a modern way
of teaching art, using digital tools in the art classroom to improve
creative ability in pupils aged between nine and eleven years. It also
presents a conceptual model for creativity based on digital art. The
model could be useful for pupils interested in learning to draw by
using an e-drawing package, and for teachers who are interested in
teaching modern digital art in order to improve children’s creativity.
By illustrating the strategy of teaching art through technology, this
model may also help education providers to make suitable choices
about which technological approaches are most effective in
enhancing students’ creative ability, and which digital art tools can
benefit children by developing their technical skills. It is also
expected that use of this model will help to develop skills of social
interaction, which may in turn improve intellectual ability.
Abstract: Information technology and information systems are
currently at a tipping point. The digital age fundamentally transforms
a large number of industries in the ways they work. Lines between
business and technology blur. Researchers have acknowledged that
this is the time in which the IT/IS organisation needs to re-strategize
itself. In this paper, the author provides a structured review of the IS
and organisation design literature addressing the question of how the
digital age changes the design categories of an IT/IS organisation
design. The findings show that most papers just analyse single
aspects of either IT/IS relevant information or generic organisation
design elements but miss a holistic ‘big-picture’ onto an IT/IS
organisation design. This paper creates a holistic IT/IS organisation
design framework bringing together the IS research strand, the digital
strand and the generic organisation design strand. The research
identified four IT/IS organisation design categories (strategy,
structure, processes and people) and discusses the importance of two
additional categories (sourcing and governance). The authors findings
point to a first anchor point from which further research needs to be
conducted to develop a holistic IT/IS organisation design framework.
Abstract: The explosion of the World Wide Web and the
electronic trend of university teaching have transformed the learning
style to become more learner-centered, which has popularized the
digital delivery of mediated lectures as an alternative or an adjunct to
traditional lectures. Despite its potential and popularity, virtual
lectures have not been adopted yet in Jordanian universities. This
research aimed to fill this gap by studying the factors that influence
students’ willingness to accept virtual lectures in one Jordanian
University. A quantitative approach was followed, by obtaining 216
survey responses and statistically applying the UTAUT model with
some modifications. Results revealed that performance expectancy,
effort expectancy, social influences, and self-efficacy could
significantly influence students’ attitudes towards virtual lectures.
Additionally, Facilitating conditions and attitudes towards virtual
lectures were found with significant influence on students’ intention
to take virtual lectures. Research implications and future work were
specified afterwards.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: Robotic surgery is used to enhance minimally invasive
surgical procedure. It provides greater degree of freedom for surgical
tools but lacks of haptic feedback system to provide sense of touch to
the surgeon. Surgical robots work on master-slave operation, where
user is a master and robotic arms are the slaves. Current, surgical
robots provide precise control of the surgical tools, but heavily rely
on visual feedback, which sometimes cause damage to the inner
organs. The goal of this research was to design and develop a realtime
Simulink based robotic system to study force feedback
mechanism during instrument-object interaction. Setup includes three
VelmexXSlide assembly (XYZ Stage) for three dimensional
movement, an end effector assembly for forceps, electronic circuit for
four strain gages, two Novint Falcon 3D gaming controllers,
microcontroller board with linear actuators, MATLAB and Simulink
toolboxes. Strain gages were calibrated using Imada Digital Force
Gauge device and tested with a hard-core wire to measure
instrument-object interaction in the range of 0-35N. Designed
Simulink model successfully acquires 3D coordinates from two
Novint Falcon controllers and transfer coordinates to the XYZ stage
and forceps. Simulink model also reads strain gages signal through
10-bit analog to digital converter resolution of a microcontroller
assembly in real time, converts voltage into force and feedback the
output signals to the Novint Falcon controller for force feedback
mechanism. Experimental setup allows user to change forward
kinematics algorithms to achieve the best-desired movement of the
XYZ stage and forceps. This project combines haptic technology
with surgical robot to provide sense of touch to the user controlling
forceps through machine-computer interface.
Abstract: Meeting the growth in demand for digital services
such as social media, telecommunications, and business and cloud
services requires large scale data centres, which has led to an increase
in their end use energy demand. Generally, over 30% of data centre
power is consumed by the necessary cooling overhead. Thus energy
can be reduced by improving the cooling efficiency. Air and liquid
can both be used as cooling media for the data centre. Traditional
data centre cooling systems use air, however liquid is recognised as a
promising method that can handle the more densely packed data
centres. Liquid cooling can be classified into three methods; rack heat
exchanger, on-chip heat exchanger and full immersion of the
microelectronics. This study quantifies the improvements of heat
transfer specifically for the case of immersed microelectronics by
varying the CPU and heat sink location. Immersion of the server is
achieved by filling the gap between the microelectronics and a water
jacket with a dielectric liquid which convects the heat from the CPU
to the water jacket on the opposite side. Heat transfer is governed by
two physical mechanisms, which is natural convection for the fixed
enclosure filled with dielectric liquid and forced convection for the
water that is pumped through the water jacket. The model in this
study is validated with published numerical and experimental work
and shows good agreement with previous work. The results show that
the heat transfer performance and Nusselt number (Nu) is improved
by 89% by placing the CPU and heat sink on the bottom of the
microelectronics enclosure.
Abstract: Content Based Image Retrieval (CBIR) coupled with
Case Based Reasoning (CBR) is a paradigm that is becoming
increasingly popular in the diagnosis and therapy planning of medical
ailments utilizing the digital content of medical images. This paper
presents a survey of some of the promising approaches used in the
detection of abnormalities in retina images as well in
mammographic screening and detection of regions of interest
in MRI scans of the brain. We also describe our proposed
algorithm to detect hard exudates in fundus images of the
retina of Diabetic Retinopathy patients.
Abstract: This study investigated some results of the use of
digital art tools by junior school children in order to discover if these
tools could promote artistic ability and creativity. The study considers
the ease of use and usefulness of the tools as well as how to assess
artwork produced by digital means. As the use of these tools is a
relatively new development in Art education, this study may help
educators in their choice of which tools to use and when to use them.
The study also aims to present a model for the assessment of
students’ artistic development and creativity by studying their artistic
activity. This model can help in determining differences in students’
creative ability and could be useful both for teachers, as a means of
assessing digital artwork, and for students, by providing the
motivation to use the tools to their fullest extent. Sixteen students
aged nine to ten years old were observed and recorded while they
used the digital drawing tools. The study found that, according to the
students’ own statements, it was not the ease of use but the successful
effects the tools provided which motivated the children to use them.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: Modelling of the earth's surface and evaluation of
urban environment, with 3D models, is an important research topic.
New stereo capabilities of high resolution optical satellites images,
such as the tri-stereo mode of Pleiades, combined with new image
matching algorithms, are now available and can be applied in urban
area analysis. In addition, photogrammetry software packages gained
new, more efficient matching algorithms, such as SGM, as well as
improved filters to deal with shadow areas, can achieve more dense
and more precise results.
This paper describes a comparison between 3D data extracted
from tri-stereo and dual stereo satellite images, combined with pixel
based matching and Wallis filter. The aim was to improve the
accuracy of 3D models especially in urban areas, in order to assess if
satellite images are appropriate for a rapid evaluation of urban
environments.
The results showed that 3D models achieved by Pleiades tri-stereo
outperformed, both in terms of accuracy and detail, the result
obtained from a Geo-eye pair. The assessment was made with
reference digital surface models derived from high resolution aerial
photography. This could mean that tri-stereo images can be
successfully used for the proposed urban change analyses.
Abstract: The use of technology in the classroom is an issue that
is constantly evolving. Digital age students learn differently than their
teachers did, so now the teacher should be constantly evolving their
methods and teaching techniques to be more in touch with the
student. In this paper a case study presents how were used some of
these technologies by accompanying a classroom course, this in order
to provide students with a different and innovative experience as their
teacher usually presented the activities to develop. As students
worked in the various activities, they increased their digital skills by
employing unknown tools that helped them in their professional
training. The twenty-first century teacher should consider the use of
Information and Communication Technologies in the classroom
thinking in skills that students of the digital age should possess. It
also takes a brief look at the history of distance education and it is
also highlighted the importance of integrating technology as part of
the student's training.
Abstract: This article is to review and understand the new
generation of students to understand their expectations and attitudes.
There are a group of students on school projects, creative work,
educational software and digital signal source, the use of social
networking tools to communicate with friends and a part in the
competition. Today's students have been described as the new
millennium students. They use information and communication
technology in a more creative and innovative at home than at school,
because the information and communication technologies for
different purposes, in the home, usually occur in school. They
collaborate and communicate more effectively when they are at
home. Most children enter school, they will bring about how to use
information and communication technologies, some basic skills and
some tips on how to use information and communication technology
will provide a more advanced than most of the school's expectations.
Many teachers can help students, however, still a lot of work,
"tradition", without a computer, and did not see the "new social
computing networks describe young people to learn and new ways of
working life in the future", in the education system of the benefits of
using a computer.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.