Abstract: Walking and sit to stand are activities carried out by
all the people many times during the day, but physical disabilities due
to age and diseases create needs of assistive devices to help elderly
people during their daily life. This study aims to study the different
types and mechanisms of the assistive devices. We will analyze the
limitations and the challenges faced by the researchers in this field.
We will introduce the Assistive Device developed at the Egypt-Japan
University of Science and Technology, named E-JUST Assistive
Device (EJAD). EJAD will be a low cost intelligent assistive device
to help elders in walking and sit-to-stand activities.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Abstract: In this paper smooth trajectories are computed in the Lie group SO(2, 1) as a motion planning problem by assigning a Frenet frame to the rigid body system to optimize the cost function of the elastic energy which is spent to track a timelike curve in Minkowski space. A method is proposed to solve a motion planning problem that minimize the integral of the square norm of Darboux vector of a timelike curve. This method uses the coordinate free Maximum Principle of Optimal control and results in the theory of integrable Hamiltonian systems. The presence of several conversed quantities inherent in these Hamiltonian systems aids in the explicit computation of the rigid body motions.
Abstract: The present study aimed to investigate whether
chlorophyll meter readings (SPAD) can be used as criterion of singleplant
selection in maize breeding. Experimentation was performed at
the ultra-low density of 0.74 plants/m2 in order the potential yield per
plant to be fully expressed. R-31 honeycomb experiments were
conducted in three different areas in Greece (Thessaloniki, Giannitsa
and Florina) using 30 inbred lines at well-watered and water-stressed
conditions during the 2012 growing season. The chlorophyll meter
readings had higher rates at dry conditions, except location of
Giannitsa where differences were not significant. Genotypes of
highest chlorophyll meter readings were consistent across areas,
emphasizing on the character’s stability. A positive correlation
between the chlorophyll meter readings and grain yield was
strengthening over time and culminated at the physiological maturity
stage. There was a clear sign that the chlorophyll meter readings has
the potential to be used for the selection of stress-adaptive genotypes
and may permit modern maize to be grown at wider range of
environments addressing the climate change scenarios.
Abstract: Because of the low maintenance and robustness induction motors have many applications in the industries. The speed control of induction motor is more important to achieve maximum torque and efficiency. Various speed control techniques like, Direct Torque Control, Sensorless Vector Control and Field Oriented Control are discussed in this paper. Soft computing technique – Fuzzy logic is applied in this paper for the speed control of induction motor to achieve maximum torque with minimum loss. The fuzzy logic controller is implemented using the Field Oriented Control technique as it provides better control of motor torque with high dynamic performance. The motor model is designed and membership functions are chosen according to the parameters of the motor model. The simulated design is tested using various tool boxes in MATLAB. The result concludes that the efficiency and reliability of the proposed speed controller is good.
Abstract: This paper deals with the combination of OSGi and
cloud computing. Both technologies are mainly placed in the field of
distributed computing. Therefore, it is discussed how different
approaches from different institutions work. In addition, the
approaches are compared to each other.
Abstract: This paper presents the methodology from machine
learning approaches for short-term rain forecasting system. Decision
Tree, Artificial Neural Network (ANN), and Support Vector Machine
(SVM) were applied to develop classification and prediction models
for rainfall forecasts. The goals of this presentation are to
demonstrate (1) how feature selection can be used to identify the
relationships between rainfall occurrences and other weather
conditions and (2) what models can be developed and deployed for
predicting the accurate rainfall estimates to support the decisions to
launch the cloud seeding operations in the northeastern part of
Thailand. Datasets collected during 2004-2006 from the
Chalermprakiat Royal Rain Making Research Center at Hua Hin,
Prachuap Khiri khan, the Chalermprakiat Royal Rain Making
Research Center at Pimai, Nakhon Ratchasima and Thai
Meteorological Department (TMD). A total of 179 records with 57
features was merged and matched by unique date. There are three
main parts in this work. Firstly, a decision tree induction algorithm
(C4.5) was used to classify the rain status into either rain or no-rain.
The overall accuracy of classification tree achieves 94.41% with the
five-fold cross validation. The C4.5 algorithm was also used to
classify the rain amount into three classes as no-rain (0-0.1 mm.),
few-rain (0.1- 10 mm.), and moderate-rain (>10 mm.) and the overall
accuracy of classification tree achieves 62.57%. Secondly, an ANN
was applied to predict the rainfall amount and the root mean square
error (RMSE) were used to measure the training and testing errors of
the ANN. It is found that the ANN yields a lower RMSE at 0.171 for
daily rainfall estimates, when compared to next-day and next-2-day
estimation. Thirdly, the ANN and SVM techniques were also used to
classify the rain amount into three classes as no-rain, few-rain, and
moderate-rain as above. The results achieved in 68.15% and 69.10%
of overall accuracy of same-day prediction for the ANN and SVM
models, respectively. The obtained results illustrated the comparison
of the predictive power of different methods for rainfall estimation.
Abstract: Cardiovascular diseases, principally atherosclerosis, are responsible for 30% of world deaths. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis.It is increasingly recognized that the initiation and progression of disease and the occurrence of clinical events is a complex interplay between the local biomechanical environment and the local vascular biology. The aim of this study is to investigate the flow behavior through a stenosed artery. A physical experiment was performed using an artery model and blood analogue fluid. An axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. The flow field was measured using particle image velocimetry (PIV). Spherical particles with 20μm diameter were seeded in a water-glycerol-NaCl mixture. Steady flow Reynolds numbers are 250. The area of interest is the region after the stenosis where the flow separation occurs. The velocity field was measured and the velocity gradient was investigated. There was high particle concentration in the recirculation zone. High velocity gradient formed immediately after the stenosis throat created a lift force that enhanced particle migration to the flow separation area.
Abstract: This research was conducted to determine responses
of chickpeas to drought in different periods (early period, late period,
no-irrigation, two times irrigation as control). The trial was made in
“Randomized Complete Block Design" with three replications on
2010 and 2011 years in Konya-Turkey. Genotypes were consisted
from 7 lines of ICARDA, 2 certified lines and 1 local population. The
results showed that; as means of years and genotypes, early period
stress showed highest (207.47 kg da-1) seed yield and it was followed
by control (202.33 kg da-1), late period (144.64 kg da-1) and normal
(106.93 kg da-1) stress applications. The genotypes were affected too
much by drought and, the lowest seed was taken from non-irrigated
plots. As the means of years and stress applications, the highest
(196.01 kg da-1) yield was taken from genotype 22255. The reason of
yield variation could be derived from different responses of
genotypes to drought.
Abstract: A preliminary evaluation of the urban land system is
presented in the article together with the instruments of land policy in
Serbia. The main reason for the analysis is demand for
definition of reform framework for urban land management in
Serbia in the period of transition towards market-led system. It
is concluded that due to the limitations of the current regulation it
will be impossible in the future to apply market principles in the
urban land policy (supply and demand of land, land capitalization,
investment efficiency, et al.). Based on the estimation that the urban
land system and land policy are key factors of competitiveness
between regions and towns in Serbia, it is necessary to initiate
changes in this field. There are indicated on an option of privatization
of urban public land and possible establishment of leasehold land. A
comparative analysis of the possibilities of the reform urban land
system in Serbia has been carried out in relation to two approaches of
market systems: (a) with dominant private ownership of urban land
(neo/liberal approach) and (b) with dominant public ownership of
urban land (system of leasehold)whose findings can be a basis for
further study of the new system in Serbia.. The attanied results are
part of studies matter for the making of Strategy of territorial
development of Serbia.
Abstract: Increasing demand on the performance of Subsea
Production Systems (SPS) suggests a need for more detailed
investigation of fluid behavior taking place in subsea equipment.
Complete CFD cool down analyses of subsea equipment are very
time demanding. The objective of this paper is to investigate a
Locked CFD approach, which enables significant reduction of the
computational time and at the same time maintains sufficient
accuracy during thermal cool down simulations. The result
comparison of a dead leg simulation using the Full CFD and the three
LCFD-methods confirms the validity of the locked flow field
assumption for the selected case. For the tested case the LCFD
simulation speed up by factor of 200 results in the absolute thermal
error of 0.5 °C (3% relative error), speed up by factor of 10 keeps the
LCFD results within 0.1 °C (0.5 % relative error) comparing to the
Full CFD.
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: Renewable and non-renewable resource constraints have been vast studied in theoretical fields of project scheduling problems. However, although cumulative resources are widespread in practical cases, the literature on project scheduling problems subject to these resources is scant. So in order to study this type of resources more, in this paper we use the framework of a resource constrained project scheduling problem (RCPSP) with finish-start precedence relations between activities and subject to the cumulative resources in addition to the renewable resources. We develop a branch and bound algorithm for this problem customizing precedence tree algorithm of RCPSP. We perform extensive experimental analysis on the algorithm to check its effectiveness and performance for solving different instances of the problem in question.
Abstract: A new nonlinear PID controller and its stability
analysis are presented in this paper. A nonlinear function is deduced
from the similarities between the control effort and the electric-field
effect of a capacitor. The conventional linear PID controller can be
modified into a nonlinear one by this function. To analyze the stability
of the nonlinear PID controlled system, an idea of energy equivalence
is adapted to avoid the conservativeness which is usually arisen from
some traditional theorems and Criterions. The energy equivalence is
naturally related with the conceptions of Passivity and T-Passivity. As
a result, an engineering guideline for the parameter design of the
nonlinear PID controller is obtained. An inverted pendulum system is
tested to verify the nonlinear PID control scheme.
Abstract: Controlled modification of appropriate sharpness for
nanotips is of paramount importance to develop novel materials and
functional devices at a nanometer resolution. Herein, we present a
reliable and unique strategy of laser irradiation enhanced
physicochemical etching to manufacture super sharp tungsten tips
with reproducible shape and dimension as well as high yields
(~80%). The corresponding morphology structure evolution of
tungsten tips and laser-tip interaction mechanisms were
systematically investigated and discussed using field emission
scanning electron microscope (SEM) and physical optics statistics
method with different fluences under 532 nm laser irradiation. This
work paves the way for exploring more accessible metallic tips
applications with tunable apex diameter and aspect ratio, and,
furthermore, facilitates the potential sharpening enhancement
technique for other materials used in a variety of nanoscale devices.
Abstract: This paper introduces an intelligent system, which can be applied in the monitoring of vehicle speed using a single camera. The ability of motion tracking is extremely useful in many automation problems and the solution to this problem will open up many future applications. One of the most common problems in our daily life is the speed detection of vehicles on a highway. In this paper, a novel technique is developed to track multiple moving objects with their speeds being estimated using a sequence of video frames. Field test has been conducted to capture real-life data and the processed results were presented. Multiple object problems and noisy in data are also considered. Implementing this system in real-time is straightforward. The proposal can accurately evaluate the position and the orientation of moving objects in real-time. The transformations and calibration between the 2D image and the actual road are also considered.
Abstract: This presentation reviews recent advances in superalloys and thermal barrier coating (TBC) for application in hot sections of energy-efficient gas-turbine engines. It has been reviewed that in the modern combined-cycle gas turbines (CCGT) applying single-crystal energy materials (SC superalloys) and thermal barrier coatings (TBC), and – in one design – closed-loop steam cooling, thermal efficiency can reach more than 60%. These technological advancements contribute to profitable and clean power generation with reduced emission. Alternatively, the use of advanced superalloys (e.g. GTD-111 superalloy, Allvac 718Plus superalloy) and advanced thermal barrier coatings (TBC) in modern gas-turbines has been shown to yield higher energy-efficiency in power generation.
Abstract: Emerging adulthood, between the ages of 18 and 25, as a new developmental stage extending from adolescence to young adulthood. According to Arnett [2004], there are experiments related to identity in three basic fields which are love, work and view of the world in emerging adulthood. When the literature related to identity is examined, it is seen that identity has been studied more with adolescent, and studies were concentrated on the relationship of identity with many demographic variables neglecting important variables such as marital status, parental status and SES. Thus, the main aim of this study is to determine whether identity statuses differenciate with marital status, parental status and SES. A total of 700 emerging adults participated in this study, and the mean age was 22,45 years [SD = 3.76]. The sample was made up of 347 female and 353 male. All participants in the study were students from colleges. Student responses to the Extended Version of the Objective Measure of Ego Identity Status [EOM-EIS-2] used to classify students into one of the four identity statuses. SPSS 15.00 program wasa used to analyse data. Percentage, frequency and X2 analysis were used in the analysis of data. When the findings of the study is viewed as a whole, the most frequently observed identity status in the group is found to be moratorium. Also, identity statuses differenciate with marital status, parental status and SES. Findings were discussed in the context of emerging adulthood.