Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: The majority of existing predictors for time series are
model-dependent and therefore require some prior knowledge for the
identification of complex systems, usually involving system
identification, extensive training, or online adaptation in the case of
time-varying systems. Additionally, since a time series is usually
generated by complex processes such as the stock market or other
chaotic systems, identification, modeling or the online updating of
parameters can be problematic. In this paper a model-free predictor
(MFP) for a time series produced by an unknown nonlinear system or
process is derived using tracking theory. An identical derivation of the
MFP using the property of the Newton form of the interpolating
polynomial is also presented. The MFP is able to accurately predict
future values of a time series, is stable, has few tuning parameters and
is desirable for engineering applications due to its simplicity, fast
prediction speed and extremely low computational load. The
performance of the proposed MFP is demonstrated using the
prediction of the Dow Jones Industrial Average stock index.
Abstract: This paper compares planning results of the electricity and water generation inventory up to year 2030 in the State of
Kuwait. Currently, the generation inventory consists of oil and gas fired technologies only. The planning study considers two main cases. The first case, Reference case, examines a generation inventory based on oil and gas fired generation technologies only.
The second case examines the inclusion of renewables as part of the generation inventory under two scenarios. In the first scenario, Ref-RE, renewable build-out is based on optimum economic performance
of overall generation system. Result shows that the optimum installed
renewable capacity with electric energy generation of 11% . In the second scenario, Ref-RE20, the renewable capacity build-out is
forced to provide 20% of electric energy by 2030. The respective energy systems costs of Reference, Ref-RE and Ref-RE20 case
scenarios reach US dollar 24, 10 and 14 billion annually in 2030.
Abstract: Rooted in the study of social functioning of space in architecture, Space Syntax (SS) and the more recent Network Pattern (NP) researches demonstrate the 'spatial structures' of city, i.e. the hierarchical patterns of streets, junctions and alley ends. Applying SS and NP models, planners can conceptualize the real city-s patterns. Although, both models yield the optimal path of the city their underpinning displays of the city-s spatial configuration differ. The Axial Map analyzes the topological non-distance-based connectivity structure, whereas, the Central-Node Map and the Shortcut-Path Map, in contrast, analyze the metrical distance-based structures. This research contrasts and combines them to understand various forms of city-s structures. It concludes that, while they reveal different spatial structures, Space Syntax and Network Pattern urban models support each the other. Combining together they simulate the global access and the locally compact structures namely the central nodes and the shortcuts for the city.
Abstract: This paper focuses on the use of project work as a
pretext for applying the conventions of writing, or the correctness of
mechanics, usage, and sentence formation, in a content-based class in
a Rajabhat University. Its aim was to explore to what extent the
student teachers’ academic achievement of the basic writing features
against the 70% attainment target after the use of project is. The
organization of work around an agreed theme in which the students
reproduce language provided by texts and instructors is expected to
enhance students’ correct writing conventions. The sample of the
study comprised of 38 fourth-year English major students. The data
was collected by means of achievement test and student writing
works. The scores in the summative achievement test were analyzed
by mean score, standard deviation, and percentage. It was found that
the student teachers do more achieve of practicing mechanics and
usage, and less in sentence formation. The students benefited from
the exposure to texts during conducting the project; however, their
automaticity of how and when to form phrases and clauses into
simple/complex sentences had room for improvement.
Abstract: In this study, direct numerical simulation for the bubble condensation in the subcooled boiling flow was performed. The main goal was to develop the CFD modeling for the bubble condensation and to evaluate the accuracy of the VOF model with the developed CFD modeling. CFD modeling for the bubble condensation was developed by modeling the source terms in the governing equations of VOF model using UDF. In the modeling, the amount of condensation was determined using the interfacial heat transfer coefficient obtained from the bubble velocity, liquid temperature and bubble diameter every time step. To evaluate the VOF model using the CFD modeling for the bubble condensation, CFD simulation results were compared with SNU experimental results such as bubble volume and shape, interfacial area, bubble diameter and bubble velocity. Simulation results predicted well the behavior of the actual condensing bubble. Therefore, it can be concluded that the VOF model using the CFD modeling for the bubble condensation will be a useful computational fluid dynamics tool for analyzing the behavior of the condensing bubble in a wide range of the subcooled boiling flow.
Abstract: Cyprus- offshore aquaculture industry has promising
prospects taking into account that Cyprus is an island. Its production
trend is increasing overtaking bigger countries such Greece and Italy.
However, current mooring systems seem to be under-performing
acting as obstacles for its future development. Furthermore, shallow
coastal waters scarcity due to competing industries dictates future
development to come by moving further from shore exposing fish
farms and subsequently mooring systems to harsher environmental
loadings. It is, therefore, of paramount importance to design mooring
systems based on engineering and scientific principles and leave
behind the present “trial and error" methods. This paper presents the
current state of Cyprus- offshore aquaculture industry and focuses of
its mooring designs by proposing a new methodology for designing
more reliable systems, hence ensuring its future.
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: A lot of recent research have spoken on the relation
between the increase of the homocysteinemia and some kinds of
cancer . For that, our study was based on the research of a possible
relation between the increase of the concentration of this amino-acid
in the plasma and the appearance of the disease of the Acute
Lymphoblastic Leukaemia in a part of Algerian children with Berber
origin in the East of Algeria . The study has done on 47 ill persons
with an average age of (09±06 ) years , with whom the disease has
diagnosed by blood and marrow examination in the hospital of blood
diseases in the CHU of Batna, and on 194 healthy witnesses of the
same age. The two groups were benefited by a dosage of the
concentration of the homocysteine vitamin B9 ,vitamin B12 , and
also of the study of special polymorphisms of indispensable enzymes
in the metabolism of this acid , and that by the use of the method (
Light cycler ) Real time PCR , on the following enzymes : MS (
C2756G ), MSR ( A66G ) ,MTHFR1 ( C677T ) and MTHFR2
(A1298C). The obtained results have revealed that the rate of the
homozygote muted genotype is the less frequent in the two groups ,
and that exist at list one genotype of each enzyme in the ill group and
in which the percentage exceed with remarkable way the same
genotype in the healthy group and we notice specially the muted
genotype GG of -the methionine synthetase-and the form TT of the
enzyme – methyline tetra hydrofolate reductase – We notice the
existence of considerable number of genotypes in the ill group lied
with characteristic increase of this Amino-acid ,and that for the
reduction of the biologic activity of these enzymes which become
inefficient in the transfer of the homocysteine into the methionine
and cause the diminution of the biologic activity of these enzymes
and with consequence the reduction of the percentage of methylic
radicals in the DNA of studied genes and that lead to the increase of
the activity and the capacity of transcription , and it-s so probably
that this last one is one of the factors of this disease especially if we
know that the specific check-up of vitamins is normal and similar in
the two groups , which ovoid the hypothesis of the reduction of
vitamins . We notice also that the heterozygote genotype is the less in
the sick category except the MTHFR2. Wild genotype is more
frequent in the witness group except MSR. Even these results are
partials; they open a new way in the genetic diagnosis of this
malicious disease which allow a precocious diagnosis and the use of
an effective and appropriated treatment in the same time.
Abstract: Facing the concern of the population to its environment and to climatic change, city planners are now considering the urban climate in their choices of planning. The urban climate, representing different urban morphologies across central Bangkok metropolitan area (BMA), are used to investigates the effects of both the composition and configuration of variables of urban morphology indicators on the summer diurnal range of urban climate, using correlation analyses and multiple linear regressions. Results show first indicate that approximately 92.6% of the variation in the average maximum daytime near-surface air temperature (Ta) was explained jointly by the two composition variables of urban morphology indicators including open space ratio (OSR) and floor area ratio (FAR). It has been possible to determine the membership of sample areas to the local climate zones (LCZs) using these urban morphology descriptors automatically computed with GIS and remote sensed data. Finally result found the temperature differences among zones of large separation, such as the city center could be respectively from 35.48±1.04ºC (Mean±S.D.) warmer than the outskirt of Bangkok on average for maximum daytime near surface temperature to 28.27±0.21ºC for extreme event and, can exceed as 8ºC. A spatially disaggregation of urban thermal responsiveness map would be helpful for several reasons. First, it would localize urban areas concerned by different climate behavior over summer daytime and be a good indicator of urban climate variability. Second, when overlaid with a land cover map, this map may contribute to identify possible urban management strategies to reduce heat wave effects in BMA.
Abstract: A macroscopic constitutive equation is developed for a high-density cellulose insulation material with emphasis on the outof- plane stress relaxation behavior. A hypothesis is proposed where the total stress is additively composed by an out-of-plane visco-elastic isotropic contribution and an in-plane elastic orthotropic response. The theory is validated against out-of-plane stress relaxation, compressive experiments and in-plane tensile hysteresis, respectively. For large scale finite element simulations, the presented model provides a balance between simplicity and capturing the materials constitutive behaviour.
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: Raw wood vinegar was purified by both standing and
filtering methods. Toxicity tests were conducted under laboratory
conditions by the topical application method (contact poison) and
feeding method (stomach poison). Larvicidal activities of wood
vinegar at four different concentrations (10, 15, 20, 25 and 30 %)
were studied against second instar larvae of housefly (Musca
domestica L.). Four replicates were maintained for all treatments and
controls. Larval mortality was recorded up to 96 hours and compared
with the larval survivability by two methods of larvicidal bioassay.
Percent pupation and percent adult emergence were observed in
treated M. domestica. The study revealed that the feeding method
gave higher efficiency compared with the topical application method.
Larval mortality increased with increasing concentration of wood
vinegar and the duration of exposure. No mortality was found in
treated M. domestica larvae at minimum 10% concentration of wood
vinegar through the experiments. The treated larvae were maintained
up to pupa and adult emergence. At 30% maximum concentration
larval duration was extended to 11 days in M. domestica for topical
application method and 9 days for feeding method. Similarly the
pupal durations were also increased with increased concentrations
(16 and 24 days for topical application method and feeding method
respectively at 30% concentration) of the treatments.
Abstract: In this paper, we propose a solution to the motion
control problem of a 2-link revolute manipulator arm. We require the
end-effector of the arm to move safely to its designated target in a
priori known workspace cluttered with fixed circular obstacles of
arbitrary position and sizes. Firstly a unique velocity algorithm is
used to move the end-effector to its target. Secondly, for obstacle
avoidance a turning angle is designed, which when incorporated into
the control laws ensures that the entire robot arm avoids any number
of fixed obstacles along its path enroute the target. The control laws
proposed in this paper also ensure that the equilibrium point of the
system is asymptotically stable. Computer simulations of the
proposed technique are presented.
Abstract: Operating rooms are important assets for hospitals as
they generate the largest revenue and, at the same time, produce the
largest cost for hospitals. The model presented in this paper helps
make capacity planning decisions on the combination of open
operating rooms (ORs) and estimated overtime to satisfy the
allocated OR time to each specialty. The model combines both
decisions on determining the amount of OR time to open and to
allocate to different surgical specialties. The decisions made are
based on OR costs, overutilization and underutilization costs, and
contribution margins from allocating OR time. The results show the
importance of having a good estimate of specialty usage of OR time
to determine the amount of needed capacity and highlighted the
tradeoff that the OR manager faces between opening more ORs
versus extending the working time of the ORs already in use.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: New theory for functionally graded (FG) shell based on expansion of the equations of elasticity for functionally graded materials (GFMs) into Legendre polynomials series has been developed. Stress and strain tensors, vectors of displacements, traction and body forces have been expanded into Legendre polynomials series in a thickness coordinate. In the same way functions that describe functionally graded relations has been also expanded. Thereby all equations of elasticity including Hook-s law have been transformed to corresponding equations for Fourier coefficients. Then system of differential equations in term of displacements and boundary conditions for Fourier coefficients has been obtained. Cases of the first and second approximations have been considered in more details. For obtained boundary-value problems solution finite element (FE) has been used of Numerical calculations have been done with Comsol Multiphysics and Matlab.