Abstract: Stormwater wetlands have been mainly designed in an
empirical approach for water quality improvement, with little
quantitative understanding of the internal microbial processes. This
study investigated into heterotrophic bacterial production rate,
heterotrophic bacterial mineralization percentage, and algal biomass
in hypertrophic and eutrophic surface flow stormwater wetlands.
Compared to a nearby wood leachate treatment wetland, the
stormwater wetlands had much higher chlorophyll-a concentrations.
The eutrophic stormwater wetland had improved water quality,
whereas the hypertrophic stormwater wetland had degraded water
quality. Heterotrophic bacterial activities in water were limited in the
stormwater wetlands due to competition of algal growth for nutrients.
The relative contribution of biofilms to the overall heterotrophic
activities was higher in the stormwater wetlands than that in the wood
leachate treatment wetland.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: In this paper a data miner based on the learning
automata is proposed and is called LA-miner. The LA-miner extracts
classification rules from data sets automatically. The proposed
algorithm is established based on the function optimization using
learning automata. The experimental results on three benchmarks
indicate that the performance of the proposed LA-miner is
comparable with (sometimes better than) the Ant-miner (a data miner
algorithm based on the Ant Colony optimization algorithm) and CNZ
(a well-known data mining algorithm for classification).
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: This paper presents a VLSI design approach of a highspeed
and real-time 2-D Discrete Wavelet Transform computing. The
proposed architecture, based on new and fast convolution approach,
reduces the hardware complexity in addition to reduce the critical
path to the multiplier delay. Furthermore, an advanced twodimensional
(2-D) discrete wavelet transform (DWT)
implementation, with an efficient memory area, is designed to
produce one output in every clock cycle. As a result, a very highspeed
is attained. The system is verified, using JPEG2000
coefficients filters, on Xilinx Virtex-II Field Programmable Gate
Array (FPGA) device without accessing any external memory. The
resulting computing rate is up to 270 M samples/s and the (9,7) 2-D
wavelet filter uses only 18 kb of memory (16 kb of first-in-first-out
memory) with 256×256 image size. In this way, the developed design
requests reduced memory and provide very high-speed processing as
well as high PSNR quality.
Abstract: This study deals with the phenomena of reflection and transmission (refraction) of qSV-waves, for an incident of quasi transverse vertically waves, at a plane interface of two semi-infinite piezoelectric elastic media under the influence of the initial stresses. The relations governing the reflection and transmission coefficients of these reflected waves for various suitable boundary conditions are derived. We have shown analytically that reflection and transmission coefficients of (qP) and (qSV) waves depend upon the angle of incidence, the parameters of electric potential, the material constants of the medium as will as the initial stresses presented in the media. The numerical calculations of the reflection and transmission amplitude ratios for different values of initial stresses have been carried out by computer for different materials as examples and the results are given in the form of graphs. Finally, some of particular cases are considered.
Abstract: In an open real-time system environment, the coexistence of different kinds of real-time and non real-time applications makes the system scheduling mechanism face new requirements and challenges. One two-level scheduling scheme of the open real-time systems is introduced, and points out that hard and soft real-time applications are scheduled non-distinctively as the same type real-time applications, the Quality of Service (QoS) cannot be guaranteed. It has two flaws: The first, it can not differentiate scheduling priorities of hard and soft real-time applications, that is to say, it neglects characteristic differences between hard real-time applications and soft ones, so it does not suit a more complex real-time environment. The second, the worst case execution time of soft real-time applications cannot be predicted exactly, so it is not worth while to cost much spending in order to assure all soft real-time applications not to miss their deadlines, and doing that may cause resource wasting. In order to solve this problem, a novel two-level real-time scheduling mechanism (including scheduling profile and scheduling algorithm) which adds the process of dealing with soft real-time applications is proposed. Finally, we verify real-time scheduling mechanism from two aspects of theory and experiment. The results indicate that our scheduling mechanism can achieve the following objectives. (1) It can reflect the difference of priority when scheduling hard and soft real-time applications. (2) It can ensure schedulability of hard real-time applications, that is, their rate of missing deadline is 0. (3) The overall rate of missing deadline of soft real-time applications can be less than 1. (4) The deadline of a non-real-time application is not set, whereas the scheduling algorithm that server 0 S uses can avoid the “starvation" of jobs and increase QOS. By doing that, our scheduling mechanism is more compatible with different types of applications and it will be applied more widely.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: Object: Review recent publications of patient safety
culture to investigate the relationship between leadership behavior,
safety culture, and safety performance in the healthcare industry.
Method: This study is a cross-sectional study, 350 questionnaires were
mailed to hospital workers with 195 valid responses obtained, and a
55.7% valid response rate. Confirmatory factor analysis (CFA) was
carried out to test the factor structure and determine if the composite
reliability was significant with a factor loading of >0.5, resulting in an
acceptable model fit. Results: Through the analysis of One-way
ANOVA, the results showed that physicians significantly have more
negative patient safety culture perceptions and safety performance
perceptions than non- physicians. Conclusions: The path analysis
results show that leadership behavior affects safety culture and safety
performance in the health care industry. Safety performance was
affected and improved with contingency leadership and a positive
patient safety organization culture. The study suggests improving
safety performance by providing a well-managed system that
includes: consideration of leadership, hospital worker training
courses, and a solid safety reporting system.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The Automatic Speech Recognition (ASR) applied to
Arabic language is a challenging task. This is mainly related to the
language specificities which make the researchers facing multiple
difficulties such as the insufficient linguistic resources and the very
limited number of available transcribed Arabic speech corpora. In
this paper, we are interested in the development of a HMM-based
ASR system for Standard Arabic (SA) language. Our fundamental
research goal is to select the most appropriate acoustic parameters
describing each audio frame, acoustic models and speech recognition
unit. To achieve this purpose, we analyze the effect of varying frame
windowing (size and period), acoustic parameter number resulting
from features extraction methods traditionally used in ASR, speech
recognition unit, Gaussian number per HMM state and number of
embedded re-estimations of the Baum-Welch Algorithm. To evaluate
the proposed ASR system, a multi-speaker SA connected-digits
corpus is collected, transcribed and used throughout all experiments.
A further evaluation is conducted on a speaker-independent continue
SA speech corpus. The phonemes recognition rate is 94.02% which is
relatively high when comparing it with another ASR system
evaluated on the same corpus.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: In the paper, based on stochastic analysis theory and Lyapunov functional method, we discuss the mean square stability of impulsive stochastic delay differential equations with markovian switching and poisson jumps, and the sufficient conditions of mean square stability have been obtained. One example illustrates the main results. Furthermore, some well-known results are improved and generalized in the remarks.
Abstract: In this paper, we construct and implement a new
Steganography algorithm based on learning system to hide a large
amount of information into color BMP image. We have used adaptive
image filtering and adaptive non-uniform image segmentation with
bits replacement on the appropriate pixels. These pixels are selected
randomly rather than sequentially by using new concept defined by
main cases with sub cases for each byte in one pixel. According to
the steps of design, we have been concluded 16 main cases with their
sub cases that covere all aspects of the input information into color
bitmap image. High security layers have been proposed through four
layers of security to make it difficult to break the encryption of the
input information and confuse steganalysis too. Learning system has
been introduces at the fourth layer of security through neural
network. This layer is used to increase the difficulties of the statistical
attacks. Our results against statistical and visual attacks are discussed
before and after using the learning system and we make comparison
with the previous Steganography algorithm. We show that our
algorithm can embed efficiently a large amount of information that
has been reached to 75% of the image size (replace 18 bits for each
pixel as a maximum) with high quality of the output.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: Real-time embedded systems should benefit from
component-based software engineering to handle complexity and
deal with dependability. In these systems, applications should not
only be logically correct but also behave within time windows.
However, in the current component based software engineering
approaches, a few of component models handles time properties in
a manner that allows efficient analysis and checking at the
architectural level. In this paper, we present a meta-model for
component-based software description that integrates timing
issues. To achieve a complete functional model of software
components, our meta-model focuses on four functional aspects:
interface, static behavior, dynamic behavior, and interaction
protocol. With each aspect we have explicitly associated a time
model. Such a time model can be used to check a component-s
design against certain properties and to compute the timing
properties of component assemblies.
Abstract: One of the most used assumptions in logic programming
and deductive databases is the so-called Closed World Assumption
(CWA), according to which the atoms that cannot be inferred
from the programs are considered to be false (i.e. a pessimistic
assumption). One of the most successful semantics of conventional
logic programs based on the CWA is the well-founded semantics.
However, the CWA is not applicable in all circumstances when
information is handled. That is, the well-founded semantics, if
conventionally defined, would behave inadequately in different cases.
The solution we adopt in this paper is to extend the well-founded
semantics in order for it to be based also on other assumptions. The
basis of (default) negative information in the well-founded semantics
is given by the so-called unfounded sets. We extend this concept
by considering optimistic, pessimistic, skeptical and paraconsistent
assumptions, used to complete missing information from a program.
Our semantics, called extended well-founded semantics, expresses
also imperfect information considered to be missing/incomplete,
uncertain and/or inconsistent, by using bilattices as multivalued
logics. We provide a method of computing the extended well-founded
semantics and show that Kripke-Kleene semantics is captured by
considering a skeptical assumption. We show also that the complexity
of the computation of our semantics is polynomial time.
Abstract: In this paper, the problem of estimating the optimal
radio capacity of a single-cell spread spectrum (SS) multiple-inputmultiple-
output (MIMO) system operating in a Rayleigh fading environment
is examined. The optimisation between the radio capacity
and the theoretically achievable average channel capacity (in the
sense of information theory) per user of a MIMO single-cell SS system
operating in a Rayleigh fading environment is presented. Then,
the spectral efficiency is estimated in terms of the achievable average
channel capacity per user, during the operation over a broadcast
time-varying link, and leads to a simple novel-closed form expression
for the optimal radio capacity value based on the maximization
of the achieved spectral efficiency. Numerical results are presented to
illustrate the proposed analysis.
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.