Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: Aurèsregion is one of the arid and semi-arid areas that
have suffered climate crises and overexploitation of natural resources
they have led to significant land degradation. The use of remote sensing data allowed us to analyze the land and
its spatiotemporal changes in the Aurès between 1987 and 2013, for
this work, we adopted a method of analysis based on the exploitation
of the images satellite Landsat TM 1987 and Landsat OLI 2013, from
the supervised classification likelihood coupled with field surveys of
the mission of May and September of 2013. Using ENVI EX software by the superposition of the ground cover
maps from 1987 and 2013, one can extract a spatial map change of
different land cover units. The results show that between 1987 and
2013 vegetation has suffered negative changes are the significant
degradation of forests and steppe rangelands, and sandy soils and
bare land recorded a considerable increase. The spatial change map land cover units between 1987 and 2013
allows us to understand the extensive or regressive orientation of
vegetation and soil, this map shows that dense forests give his place
to clear forests and steppe vegetation develops from a degraded forest
vegetation and bare, sandy soils earn big steppe surfaces that explain
its remarkable extension.
The analysis of remote sensing data highlights the profound
changes in our environment over time and quantitative monitoring of
the risk of desertification.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: This paper presents a state-of-the-art survey of the
operations research models developed for internal audit planning.
Two alternative approaches have been followed in the literature for
audit planning: (1) identifying the optimal audit frequency; and (2)
determining the optimal audit resource allocation. The first approach
identifies the elapsed time between two successive audits, which can
be presented as the optimal number of audits in a given planning
horizon, or the optimal number of transactions after which an audit
should be performed. It also includes the optimal audit schedule. The
second approach determines the optimal allocation of audit frequency
among all auditable units in the firm. In our review, we discuss both
the deterministic and probabilistic models developed for audit
planning. In addition, game theory models are reviewed to find the
optimal auditing strategy based on the interactions between the
auditors and the clients.
Abstract: Optic disk segmentation plays a key role in the mass
screening of individuals with diabetic retinopathy and glaucoma
ailments. An efficient hardware-based algorithm for optic disk
localization and segmentation would aid for developing an automated
retinal image analysis system for real time applications. Herein,
TMS320C6416DSK DSP board pixel intensity based fractal analysis
algorithm for an automatic localization and segmentation of the optic
disk is reported. The experiment has been performed on color and
fluorescent angiography retinal fundus images. Initially, the images
were pre-processed to reduce the noise and enhance the quality. The
retinal vascular tree of the image was then extracted using canny
edge detection technique. Finally, a pixel intensity based fractal
analysis is performed to segment the optic disk by tracing the origin
of the vascular tree. The proposed method is examined on three
publicly available data sets of the retinal image and also with the data
set obtained from an eye clinic. The average accuracy achieved is
96.2%. To the best of the knowledge, this is the first work reporting
the use of TMS320C6416DSK DSP board and pixel intensity based
fractal analysis algorithm for an automatic localization and
segmentation of the optic disk. This will pave the way for developing
devices for detection of retinal diseases in the future.
Abstract: This paper directs attention to the limitations of the
teacher-centered strategy in teaching. The aim of this study is to draw
more educational attention to learner-centered strategy in order to
shift the emphasis from the traditional concept of teaching to a new
concept in teaching. To begin bridging the traditional concept of
teaching and the new concept, the study will explore the new concept
of teaching to support teaching in Arab World generally and in Iraq
specifically. A qualitative case study orientation was used to collect
data in the form of classroom observations, interviews and field
notes. The teaching practices used by three university instructors are
investigated and according to the findings, some explanations and
recommendations are made.
Abstract: Background: The change in foot posture can possibly
generate changes in the pelvic alignment. There is still a lack of
evidence about the effects of bilateral and unilateral flatfoot on
possible changes in pelvic alignment. The purpose of this study was
to investigate the effect of flatfoot on the sagittal and frontal planes of
pelvic postures. Materials and Methods: 56 subjects, aged 18–40
years, were assigned into three groups: 20 healthy subjects, 19
subjects with bilateral flexible second-degree flat foot, and 17
subjects with unilateral flexible second-degree flat foot. 3D
assessment of the pelvis using the formetric-II device was used to
evaluate pelvic alignment in the frontal and sagittal planes by
measuring pelvic inclination and pelvic tilt angles. Results: ANOVA
test with LSD test were used for statistical analysis. Both Unilateral
and bilateral second degree flatfoot produced significant (P
Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.
Abstract: The article describes the effect of the replacement of
the used reference coordinate system in the georeferencing of an old
map of Europe. The map was georeferenced into three types of
projection – the equal-area conic (original cartographic projection),
cylindrical Plate Carrée and cylindrical Mercator map projection. The
map was georeferenced by means of the affine and the second-order
polynomial transformation. The resulting georeferenced raster
datasets from the Plate Carrée and Mercator projection were
projected into the equal-area conic projection by means of projection
equations. The output is the comparison of drawn graphics, the
magnitude of standard deviations for individual projections and types
of transformation.
Abstract: Single angle connections, which are bolted to the beam
web and the column flange, are studied to investigate their
moment-rotation behavior. Elastic–perfectly plastic material behavior
is assumed. ABAQUS software is used to analyze the nonlinear
behavior of a single angle connection. The identical geometric and
material conditions with Lipson’s test are used for verifying finite
element models. Since Kishi and Chen’s Power model and Lee and
Moon’s Log model are accurate only for a limited range of mechanism,
simpler and more accurate hyperbolic function models are proposed.
Abstract: The environmental, cultural, social, and technological
changes have led higher education institutes to question their
traditional roles. Many declarations and frameworks highlight the
importance of fulfilling social responsibility of higher education
institutes. The study aims at developing a framework of university
social responsibility and sustainability (USR&S) with focus on South
Valley University (SVU) as a case study of Egyptian Universities.
The study used meetings with 12 vice deans of community services
and environmental affairs on social responsibility and environmental
issues. The proposed framework integrates social responsibility with
strategic management through the establishment and maintenance of
the vision, mission, values, goals and management systems;
elaboration of policies; provision of actions; evaluation of services
and development of social collaboration with stakeholders to meet
current and future needs of the community and environment. The
framework links between different stakeholders internally and
externally using communication and reporting tools. The results show
that SVU integrates social responsibility and sustainability in its
strategic plans. It has policies and actions however fragmented and
lack of appropriate structure and budgeting. The proposed framework
could be valuable for researchers and decision makers of the
Egyptian Universities. The study proposed recommendations and
highlighted building on the results and conducting future research.
Abstract: Present work deals with the possible use of fertigation
in agriculture and its impact on the availability of mineral nitrogen
(Nmin) in topsoil and subsoil horizons. The aim of the present study is
to demonstrate the effect of the organic matter presence in fertigation
on microbial transformation and availability of mineral nitrogen
forms. The main investigation reason is the potential use of pretreated
waste water, as a source of organic carbon (Corg) and residual
nutrients (Nmin) for fertigation. Laboratory experiment has been
conducted to demonstrate the effect of the arable land fertilization
method on the Nmin availability in different depths of the soil with
the usage of model experimental containers filled with soil from
topsoil and podsoil horizons that were taken from the precise area.
Tufted hairgrass (Deschampsia caespitosa) has been chosen as a
model plant. The water source protection zone Brezova nad Svitavou
has been a research area where significant underground reservoirs of
drinking water of the highest quality are located. From the second
half of the last century local sources of drinking water show
nitrogenous compounds increase that get here almost only from
arable lands. Therefore, an attention of the following text focuses on
the fate of mineral nitrogen in the complex plant-soil. Research
results show that the fertigation application with Corg in a
combination with mineral fertilizer can reduce the amount of Nmin
leached from topsoil horizon of agricultural soils. In addition, some
plants biomass production reduces may occur.
Abstract: The study is in application and analysis of two tourism
management tools that can contribute to making public managers
decision: the Barometer of Tourism Sustainability (BTS) and the
Ecological Footprint (EF). The results have shown that BTS allows
you to have an integrated view of the tourism system, awakening to
the need for planning of appropriate actions so that it can achieve the
positive scale proposed (potentially sustainable). Already the
methodology of ecological tourism footprint is an important tool to
measure potential impacts generated by tourism to tourist reality.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: The growth of organic farming practices in the last
few decades is continuing to stimulate the international debate about
this alternative food market. As a part of a PhD project research
about embeddedness in Alternative Food Networks (AFNs), this
paper focuses on the promotional aspects of organic farms websites
from the Madrid region. As a theoretical tool, some knowledge
categories drawn on the geographic studies literature are used to
classify the many ideas expressed in the web pages. By analysing
texts and pictures of 30 websites, the study aims to question how and
to what extent actors from organic world communicate to the
potential customers their personal beliefs about farming practices,
products qualities, and ecological and social benefits. Moreover, the
paper raises the question of whether organic farming laws and
regulations lack of completeness about the social and cultural aspects
of food.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.