Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: The healthcare environment is generally perceived as
being information rich yet knowledge poor. However, there is a lack
of effective analysis tools to discover hidden relationships and trends
in data. In fact, valuable knowledge can be discovered from
application of data mining techniques in healthcare system. In this
study, a proficient methodology for the extraction of significant
patterns from the Coronary Heart Disease warehouses for heart
attack prediction, which unfortunately continues to be a leading cause
of mortality in the whole world, has been presented. For this purpose,
we propose to enumerate dynamically the optimal subsets of the
reduced features of high interest by using rough sets technique
associated to dynamic programming. Therefore, we propose to
validate the classification using Random Forest (RF) decision tree to
identify the risky heart disease cases. This work is based on a large
amount of data collected from several clinical institutions based on
the medical profile of patient. Moreover, the experts- knowledge in
this field has been taken into consideration in order to define the
disease, its risk factors, and to establish significant knowledge
relationships among the medical factors. A computer-aided system is
developed for this purpose based on a population of 525 adults. The
performance of the proposed model is analyzed and evaluated based
on set of benchmark techniques applied in this classification problem.
Abstract: Stable nonzero populations without random deaths
caused by the Verhulst factor (Verhulst-free) are a rarity. Majority
either grow without bounds or die of excessive harmful mutations.
To delay the accumulation of bad genes or diseases, a new
environmental parameter Γ is introduced in the simulation. Current
results demonstrate that stability may be achieved by setting Γ = 0.1.
These steady states approach a maximum size that scales inversely
with reproduction age.
Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: The design of Automatic Generation Control (AGC) system plays a vital role in automation of power system. This paper proposes Hybrid Neuro Fuzzy (HNF) approach for AGC of two-area interconnected reheat thermal power system with the consideration of Generation Rate Constraint (GRC). The advantage of proposed controller is that it can handle the system non-linearities and at the same time the proposed approach is faster than conventional controllers. The performance of HNF controller has been compared with that of both conventional Proportional Integral (PI) controller as well as Fuzzy Logic Controller (FLC) both in the absence and presence of Generation Rate Constraint (GRC). System performance is examined considering disturbance in each area of interconnected power system.
Abstract: Direct search methods are evolutionary algorithms used to solve optimization problems. (DS) methods do not require any information about the gradient of the objective function at hand while searching for an optimum solution. One of such methods is Pattern Search (PS) algorithm. This paper presents a new approach based on a constrained pattern search algorithm to solve a security constrained power system economic dispatch problem (SCED). Operation of power systems demands a high degree of security to keep the system satisfactorily operating when subjected to disturbances, while and at the same time it is required to pay attention to the economic aspects. Pattern recognition technique is used first to assess dynamic security. Linear classifiers that determine the stability of electric power system are presented and added to other system stability and operational constraints. The problem is formulated as a constrained optimization problem in a way that insures a secure-economic system operation. Pattern search method is then applied to solve the constrained optimization formulation. In particular, the method is tested using one system. Simulation results of the proposed approach are compared with those reported in literature. The outcome is very encouraging and proves that pattern search (PS) is very applicable for solving security constrained power system economic dispatch problem (SCED).
Abstract: This research investigates the use of digital technology
namely interactive multimedia in effective art education provided by
museum. Several multimedia experience examples created for art
education are study case subjected to assistance audiences- learning
within the context of existing theory in the field of interactive
multimedia.
Abstract: A numerical method is developed for simulating
the motion of particles with arbitrary shapes in an effectively
infinite or bounded viscous flow. The particle translational and
angular motions are numerically investigated using a fluid-structure
interaction (FSI) method based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (smoothing and
remeshing) in FLUENT ( ANSYS Inc., USA). Also, the effects of
arbitrary shapes on the dynamics are studied using the FSI method
which could be applied to the motions and deformations of a single
blood cell and multiple blood cells, and the primary thrombogenesis
caused by platelet aggregation. It is expected that, combined with a
sophisticated large-scale computational technique, the simulation
method will be useful for understanding the overall properties of blood
flow from blood cellular level (microscopic) to the resulting
rheological properties of blood as a mass (macroscopic).
Abstract: We see in the present day scenario that the Global
positioning system (GPS) has been an effective tool to track the
vehicle. However the adverse part of it is that it can only track a
vehicle-s position. Our present work provides a better platform to
track and disable a vehicle using wireless technology. In our system
we embed a microcomputer which monitors the series of automotive
systems like engine, fuel and braking system. The external USB
modem is connected with the microcomputer to provide 24 x 7
internet accesses. The microcomputer is synchronized with the
owner-s multimedia mobile by means of a software tool “REMOTE
DESKTOP". A unique username and password is provided to the
software tool, so that the owner can only access the microcomputer
through the internet on owner-s mobile. The key fact is that our
design is placed such that it is known only to the owner.
Abstract: In the present paper, active control system is used in
different heights of the building and the most effective part was
studied where the active control system is applied. The mathematical
model of the building is established in MATLAB and in order to
active control the system FLC method was used. Three different
locations of the building are chosen to apply active control system,
namely at the lowest story, the middle height of the building, and at
the highest point of the building with TMD system. The equation of
motion was written for high rise building and it was solved by statespace
method. Also passive control was used with Tuned Mass
Damper (TMD) at the top floor of the building to show the robustness
of FLC method when compared with passive control system.
Abstract: Knowledge is attributed to human whose problemsolving
behavior is subjective and complex. In today-s knowledge
economy, the need to manage knowledge produced by a community
of actors cannot be overemphasized. This is due to the fact that
actors possess some level of tacit knowledge which is generally
difficult to articulate. Problem-solving requires searching and sharing
of knowledge among a group of actors in a particular context.
Knowledge expressed within the context of a problem resolution
must be capitalized for future reuse. In this paper, an approach that
permits dynamic capitalization of relevant and reliable actors-
knowledge in solving decision problem following Economic
Intelligence process is proposed. Knowledge annotation method and
temporal attributes are used for handling the complexity in the
communication among actors and in contextualizing expressed
knowledge. A prototype is built to demonstrate the functionalities of
a collaborative Knowledge Management system based on this
approach. It is tested with sample cases and the result showed that
dynamic capitalization leads to knowledge validation hence
increasing reliability of captured knowledge for reuse. The system
can be adapted to various domains.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Modern managements of water distribution system
(WDS) need water quality models that are able to accurately predict
the dynamics of water quality variations within the distribution system
environment. Before water quality models can be applied to solve
system problems, they should be calibrated. Although former
researchers use GA solver to calibrate relative parameters, it is
difficult to apply on the large-scale or medium-scale real system for
long computational time. In this paper a new method is designed
which combines both macro and detailed model to optimize the water
quality parameters. This new combinational algorithm uses radial
basis function (RBF) metamodeling as a surrogate to be optimized for
the purpose of decreasing the times of time-consuming water quality
simulation and can realize rapidly the calibration of pipe wall reaction
coefficients of chlorine model of large-scaled WDS. After two cases
study this method is testified to be more efficient and promising, and
deserve to generalize in the future.
Abstract: Development of motor car safety devices has reduced
fatality rates in car accidents. Yet despite this increase in car safety,
neck injuries resulting from rear impact collisions, particularly at low
speed, remain a primary concern. In this study, FEA(Finite Element
Analysis) of seat was performed to evaluate neck injuries in rear
impact. And the FEA result was verified by comparison with the actual
test results. The dummy used in FE model and actual test is BioRID II
which is regarded suitable for rear impact collision analysis. A
threshold of the BioRID II neck injury indicators was also proposed to
upgrade seat performance in order to reduce whiplash injury. To
optimize the seat for a low-speed rear impact collision, a method was
proposed, which is multi-objective optimization idea using DOE
(Design of Experiments) results.
Abstract: Disordered function of maniphalanx and difficulty with
ambulation will occur insofar as a human has a failure in the spinal
marrow. Cervical spondylotic myelopathy as one of the myelopathy
emanates from not only external factors but also increased age. In
addition, the diacrisis is difficult since cervical spondylotic
myelopathy is evaluated by a doctor-s neurological remark and
imaging findings. As a quantitative method for measuring the degree
of disability, hand-operated triangle step test (for short, TST) has
formulated. In this research, a full automatic triangle step counter
apparatus is designed and developed to measure the degree of
disability in an accurate fashion according to the principle of TST. The
step counter apparatus whose shape is a low triangle pole displays the
number of stepping upon each corner. Furthermore, the apparatus has
two modes of operation. Namely, one is for measuring the degree of
disability and the other for rehabilitation exercise. In terms of
usefulness, clinical practice should be executed before too long.
Abstract: In this paper, we present user pattern learning
algorithm based MDSS (Medical Decision support system) under
ubiquitous. Most of researches are focus on hardware system, hospital
management and whole concept of ubiquitous environment even
though it is hard to implement. Our objective of this paper is to design
a MDSS framework. It helps to patient for medical treatment and
prevention of the high risk patient (COPD, heart disease, Diabetes).
This framework consist database, CAD (Computer Aided diagnosis
support system) and CAP (computer aided user vital sign prediction
system). It can be applied to develop user pattern learning algorithm
based MDSS for homecare and silver town service. Especially this
CAD has wise decision making competency. It compares current vital
sign with user-s normal condition pattern data. In addition, the CAP
computes user vital sign prediction using past data of the patient. The
novel approach is using neural network method, wireless vital sign
acquisition devices and personal computer DB system. An intelligent
agent based MDSS will help elder people and high risk patients to
prevent sudden death and disease, the physician to get the online
access to patients- data, the plan of medication service priority (e.g.
emergency case).
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of pulping problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified odified problem M-1 Ax= M-1b where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.