Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.
Abstract: This paper describes a novel sensor device, a pressure
pulse wave meter, which uses a bidirectional condenser microphone.
The microphone work as a microphone as well as a sensor with high
gain over a wide frequency range; they are also highly reliable and
economic. Currently aging is becoming a serious social issue in Japan causing
increased medical expenses in the country. Hence, it is important for
elderly citizens to check health condition at home, and to care the
health conditions through daily monitoring. Given this circumstances,
we developed a novel pressure pulse wave meter based on a
bidirectional condenser microphone: this device is used as a measuring
instrument of health conditions.
Abstract: In this paper, we explore the macroeconomic effects
of the European Single Market on Austria by simulating the
McKibbin-Sachs Global Model. Global interdependences and the
impact of long-run effects on short-run adjustments are taken into
account. We study the sensitivity of the results with respect to
different assumptions concerning monetary and fiscal policies for the
countries and regions of the world economy. The consequences of
different assumptions about budgetary policies in Austria are also
investigated. The simulation results are contrasted with ex-post
evaluations of the actual impact of Austria’s membership in the
Single Market. As a result, it can be concluded that the Austrian
participation in the European Single Market entails considerable
long-run gains for the Austrian economy with nearly no adverse sideeffects
on any macroeconomic target variable.
Abstract: In this study, the signal of brain electrical activities of
the sixteen students selected from the Department of Electrical and
Energy at Usak University have been recorded during a lecturer
performed happiness emotions for the first group and anger emotions
for the second group in different time while the groups were in the
classroom separately. The attention and meditation data extracted
from the recorded signals have been analyzed and evaluated toward
the teacher’s specific emotion states simultaneously. Attention levels
of students who are under influence of happiness emotions of the
lecturer have a positive trend and attention levels of students who are
under influence of anger emotions of the lecturer have a negative
trend. The meditation or mental relaxation levels of students who are
under influence of happiness emotions of the lecturer are 34.3%
higher comparing with the mental relaxation levels of students who
are under influence of anger emotions of the lecturer.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: The goal of this experiment is to evaluate the
effectiveness of different leachate pre-treatment options in terms of
COD and ammonia removal. This research focused on the evaluation
of physical-chemical methods for pre-treatment of leachate that
would be effective and rapid in order to satisfy the requirements of
the sewer discharge by-laws. The four pre-treatment options
evaluated were: air stripping, chemical coagulation, electrocoagulation
and advanced oxidation with sodium ferrate. Chemical
coagulation reported the best COD removal rate at 43%, compared to
18% for both air stripping and electro-coagulation, and 20% for
oxidation with sodium ferrate. On the other hand, air stripping was
far superior to the other treatment options in terms of ammonia
removal with 86%. Oxidation with sodium ferrate reached only 16%,
while chemical coagulation and electro-coagulation removed less
than 10%. When combined, air stripping and chemical coagulation
removed up to 50% COD and 85% ammonia.
Abstract: The environmental, cultural, social, and technological
changes have led higher education institutes to question their
traditional roles. Many declarations and frameworks highlight the
importance of fulfilling social responsibility of higher education
institutes. The study aims at developing a framework of university
social responsibility and sustainability (USR&S) with focus on South
Valley University (SVU) as a case study of Egyptian Universities.
The study used meetings with 12 vice deans of community services
and environmental affairs on social responsibility and environmental
issues. The proposed framework integrates social responsibility with
strategic management through the establishment and maintenance of
the vision, mission, values, goals and management systems;
elaboration of policies; provision of actions; evaluation of services
and development of social collaboration with stakeholders to meet
current and future needs of the community and environment. The
framework links between different stakeholders internally and
externally using communication and reporting tools. The results show
that SVU integrates social responsibility and sustainability in its
strategic plans. It has policies and actions however fragmented and
lack of appropriate structure and budgeting. The proposed framework
could be valuable for researchers and decision makers of the
Egyptian Universities. The study proposed recommendations and
highlighted building on the results and conducting future research.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: This paper presents the design, development and
evaluation of an application prototype developed to support
tuberculosis (TB) patients’ treatment adherence. The system makes
use of graphics and voice reminders as opposed to text messaging to
encourage patients to follow their medication routine. To evaluate the
effect of the prototype applications, participants were given mobile
phones on which the reminder system was installed. Thirty-eight
people, including TB health workers and patients from Zanzibar,
Tanzania, participated in the evaluation exercises. The results
indicate that the participants found the mobile image-based
application is useful to support TB treatment. All participants
understood and interpreted the intended meaning of every image
correctly. The study findings revealed that the use of a mobile visualbased
application may have potential benefit to support TB patients
(both literate and illiterate) in their treatment processes.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: The main objective of this study was to assess the
seasonal variation of atmospheric polycyclic aromatic hydrocarbon
(PAH) concentrations associated with PM10 in an urban site of Győr,
Hungary. A total of 112 PM10 aerosol samples were collected in the
years of 2012 and 2013 and analyzed for PAHs by gas
chromatography method. The total PAH concentrations (sum of the
concentrations of 19 individual PAH compounds) ranged from 0.19
to 70.16 ng/m3 with the mean value of 12.29 ng/m3. Higher
concentrations of both total PAHs and benzo[a]pyrene (BaP) were
detected in samples collected in the heating seasons. Using BaPequivalent
potency index on the carcinogenic PAH concentration
data, the local population appears to be exposed to significantly
higher cancer risk in the heating seasons. However, the comparison
of the BaP and total PAH concentrations observed for Győr with
other cities it was found that the PAH levels in Győr generally
corresponded to the EU average.
Abstract: Neural activity in the human brain starts from the
early stages of prenatal development. This activity or signals
generated by the brain are electrical in nature and represent not only
the brain function but also the status of the whole body. At the
present moment, three methods can record functional and
physiological changes within the brain with high temporal resolution
of neuronal interactions at the network level: the
electroencephalogram (EEG), the magnet oencephalogram (MEG),
and functional magnetic resonance imaging (fMRI); each of these has
advantages and shortcomings. EEG recording with a large number of
electrodes is now feasible in clinical practice. Multichannel EEG
recorded from the scalp surface provides very valuable but indirect
information about the source distribution. However, deep electrode
measurements yield more reliable information about the source
locations intracranial recordings and scalp EEG are used with the
source imaging techniques to determine the locations and strengths of
the epileptic activity. As a source localization method, Low
Resolution Electro-Magnetic Tomography (LORETA) is solved for
the realistic geometry based on both forward methods, the Boundary
Element Method (BEM) and the Finite Difference Method (FDM). In
this paper, we review the findings EEG- LORETA about epilepsy.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.