Abstract: In this study free vibration analysis of aluminum
honeycomb sandwich structures were carried out experimentally and
numerically. The natural frequencies and mode shapes of sandwich
structures fabricated with different configurations for clamped-free
boundary condition were determined. The effects of lower and upper
face sheet thickness, the core material thickness, cell diameter, cell
angle and foil thickness on the vibration characteristics were
examined. The numerical studies were performed with ANSYS
package. While the sandwich structures were modeled in ANSYS the
continuum model was used. Later, the numerical results were
compared with the experimental findings.
Abstract: This paper proposed the comparison made between
Multi-Carrier Pulse Width Modulation, Sinusoidal Pulse Width
Modulation and Selective Harmonic Elimination Pulse Width
Modulation technique for minimization of Total Harmonic Distortion
in Cascaded H-Bridge Multi-Level Inverter. In Multicarrier Pulse
Width Modulation method by using Alternate Position of Disposition
scheme for switching pulse generation to Multi-Level Inverter.
Another carrier based approach; Sinusoidal Pulse Width Modulation
method is also implemented to define the switching pulse generation
system in the multi-level inverter. In Selective Harmonic Elimination
method using Genetic Algorithm and Particle Swarm Optimization
algorithm for define the required switching angles to eliminate low
order harmonics from the inverter output voltage waveform and
reduce the total harmonic distortion value. So, the results validate that
the Selective Harmonic Elimination Pulse Width Modulation method
does capably eliminate a great number of precise harmonics and
minimize the Total Harmonic Distortion value in output voltage
waveform in compared with Multi-Carrier Pulse Width Modulation
method, Sinusoidal Pulse Width Modulation method. In this paper,
comparison of simulation results shows that the Selective Harmonic
Elimination method can attain optimal harmonic minimization
solution better than Multi-Carrier Pulse Width Modulation method,
Sinusoidal Pulse Width Modulation method.
Abstract: This paper represents the results of experimental work to investigate the suitability of a waste material (WM) for soft soil stabilisation. In addition, the effect of particle size distribution (PSD) of the waste material on its performance as a soil stabiliser was investigated. The WM used in this study is produced from the incineration processes in domestic energy power plant and it is available in two different grades of fineness (coarse waste material (CWM) and fine waste material (FWM)). An intermediate plasticity silty clayey soil with medium organic matter content has been used in this study. The suitability of the CWM and FWM to improve the physical and engineering properties of the selected soil was evaluated dependant on the results obtained from the consistency limits, compaction characteristics (optimum moisture content (OMC) and maximum dry density (MDD)); along with the unconfined compressive strength test (UCS). Different percentages of CWM were added to the soft soil (3, 6, 9, 12 and 15%) to produce various admixtures. Then the UCS test was carried out on specimens under different curing periods (zero, 7, 14, and 28 days) to find the optimum percentage of CWM. The optimum and other two percentages (either side of the optimum content) were used for FWM to evaluate the effect of the fineness of the WM on UCS of the stabilised soil. Results indicated that both types of the WM used in this study improved the physical properties of the soft soil where the index of plasticity (IP) was decreased significantly. IP was decreased from 21 to 13.64 and 13.10 with 12% of CWM and 15% of FWM respectively. The results of the unconfined compressive strength test indicated that 12% of CWM was the optimum and this percentage developed the UCS value from 202kPa to 500kPa for 28 days cured samples, which is equal, approximately 2.5 times the UCS value for untreated soil. Moreover, this percentage provided 1.4 times the value of UCS for stabilized soil-CWA by using FWM which recorded just under 700kPa after 28 days curing.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: The crude methanol extracts of five indigenous vegetables namely, Amarathus tricolor, Basella rubra L., Chochurus olitorius L., Ipomea batatas, and Momordica chuchinensis L., were examined for their phytochemical profile and antioxidant activity using 1,1-diphenyl-2-picrylhydrazyl (DPPH) free radical. The values for DPPH radical scavenging activity ranged from 7.6-89.53% with B. rubra and I. batatas having the lowest and highest values, respectively. The total flavonoid content of all five indigenous vegetables ranged from 74.65-277.3 mg quercetin equivalent per gram of dried vegetable material while the total phenolic content ranged from 1.93-6.15 mg gallic acid equivalent per gram dried material. Phytochemical screening revealed the presence of steroids, flavonoids, saponins, tannins, carbohydrates and reducing sugars, which may also be associated with the antioxidant activity shown by these indigenous vegetables.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: STRIM (Statistical Test Rule Induction Method) has been proposed as a method to effectively induct if-then rules from the decision table which is considered as a sample set obtained from the population of interest. Its usefulness has been confirmed by simulation experiments specifying rules in advance, and by comparison with conventional methods. However, scope for future development remains before STRIM can be applied to the analysis of real-world data sets. The first requirement is to determine the size of the dataset needed for inducting true rules, since finding statistically significant rules is the core of the method. The second is to examine the capacity of rule induction from datasets with contaminated attribute values created by missing data and noise, since real-world datasets usually contain such contaminated data. This paper examines the first problem theoretically, in connection with the rule length. The second problem is then examined in a simulation experiment, utilizing the critical size of dataset derived from the first step. The experimental results show that STRIM is highly robust in the analysis of datasets with contaminated attribute values, and hence is applicable to real-world data
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.
Abstract: The main objective of this study was to assess the
annual concentration and seasonal variation of benzo(a)pyrene (BaP)
associated with PM10 in an urban site of Győr and in a rural site of
Sarród in the sampling period of 2008–2012. A total of 280 PM10
aerosol samples were collected in each sampling site and analyzed for
BaP by gas chromatography method. The BaP concentrations ranged
from undetected to 8 ng/m3 with the mean value of 1.01 ng/m3 in the
sampling site of Győr, and from undetected to 4.07 ng/m3 with the
mean value of 0.52 ng/m3 in the sampling site of Sarród, respectively.
Relatively higher concentrations of BaP were detected in samples
collected in both sampling sites in the heating seasons compared with
non-heating periods. The annual mean BaP concentrations were
comparable with the published data of different other Hungarian
sites.
Abstract: In present study, it was aimed to determine potential
agricultural lands (PALs) in Gokceada (Imroz) Island of Canakkale
province, Turkey. Seven-band Landsat 8 OLI images acquired on
July 12 and August 13, 2013, and their 14-band combination image
were used to identify current Land Use Land Cover (LULC) status.
Principal Component Analysis (PCA) was applied to three Landsat
datasets in order to reduce the correlation between the bands. A total
of six Original and PCA images were classified using supervised
classification method to obtain the LULC maps including 6 main
classes (“Forest”, “Agriculture”, “Water Surface”, “Residential Area-
Bare Soil”, “Reforestation” and “Other”). Accuracy assessment was
performed by checking the accuracy of 120 randomized points for
each LULC maps. The best overall accuracy and Kappa statistic
values (90.83%, 0.8791% respectively) were found for PCA images
which were generated from 14-bands combined images called 3-
B/JA.
Digital Elevation Model (DEM) with 15 m spatial resolution
(ASTER) was used to consider topographical characteristics. Soil
properties were obtained by digitizing 1:25000 scaled soil maps of
Rural Services Directorate General. Potential Agricultural Lands
(PALs) were determined using Geographic information Systems
(GIS). Procedure was applied considering that “Other” class of
LULC map may be used for agricultural purposes in the future
properties. Overlaying analysis was conducted using Slope (S), Land
Use Capability Class (LUCC), Other Soil Properties (OSP) and Land
Use Capability Sub-Class (SUBC) properties.
A total of 901.62 ha areas within “Other” class (15798.2 ha) of
LULC map were determined as PALs. These lands were ranked as
“Very Suitable”, “Suitable”, “Moderate Suitable” and “Low
Suitable”. It was determined that the 8.03 ha were classified as “Very
Suitable” while 18.59 ha as suitable and 11.44 ha as “Moderate
Suitable” for PALs. In addition, 756.56 ha were found to be “Low
Suitable”. The results obtained from this preliminary study can serve
as basis for further studies.
Abstract: The flow duration curve (FDC) is an informative
method that represents the flow regime’s properties for a river basin.
Therefore, the FDC is widely used for water resource projects such as
hydropower, water supply, irrigation and water quality management.
The primary purpose of this study is to obtain synthetic daily flow
duration curves for Çoruh Basin, Turkey. For this aim, we firstly
developed univariate auto-regressive moving average (ARMA)
models for daily flows of 9 stations located in Çoruh basin and then
these models were used to generate 100 synthetic flow series each
having same size as historical series. Secondly, flow duration curves
of each synthetic series were drawn and the flow values exceeded 10,
50 and 95% of the time and 95% confidence limit of these flows were
calculated. As a result, flood, mean and low flows potential of Çoruh
basin will comprehensively be represented.
Abstract: To construct the lumped spring-mass model
considering the occupants for the offset frontal crash, the SISAME
software and the NHTSA test data were used. The data on 56 kph 40%
offset frontal vehicle to deformable barrier crash test of a MY2007
Mazda 6 4-door sedan were obtained from NHTSA test database. The
overall behaviors of B-pillar and engine of simulation models agreed
very well with the test data. The trends of accelerations at the driver
and passenger head were similar but big differences in peak values.
The differences of peak values caused the large errors of the HIC36
and 3 ms chest g’s. To predict well the behaviors of dummies, the
spring-mass model for the offset frontal crash needs to be improved.
Abstract: Designing cost-efficient, secure network protocols for
Wireless Sensor Networks (WSNs) is a challenging problem because
sensors are resource-limited wireless devices. Security services such
as authentication and improved pairwise key establishment are
critical to high efficient networks with sensor nodes. For sensor
nodes to correspond securely with each other efficiently, usage of
cryptographic techniques is necessary. In this paper, two key
predistribution schemes that enable a mobile sink to establish a
secure data-communication link, on the fly, with any sensor nodes.
The intermediate nodes along the path to the sink are able to verify
the authenticity and integrity of the incoming packets using a
predicted value of the key generated by the sender’s essential power.
The proposed schemes are based on the pairwise key with the mobile
sink, our analytical results clearly show that our schemes perform
better in terms of network resilience to node capture than existing
schemes if used in wireless sensor networks with mobile sinks.
Abstract: Under active stress conditions, a rigid cantilever
retaining wall tends to rotate about a pivot point located within the
embedded depth of the wall. For purely granular and cohesive soils, a
methodology was previously reported called minimization of moment
ratio to determine the location of the pivot point of rotation. The
usage of this new methodology is to estimate the rotational stability
safety factor. Moreover, the degree of improvement required in a
backfill to get a desired safety factor can be estimated by the concept
of the shear strength demand. In this article, the accuracy of this
method for another type of cantilever walls called Contiguous Bored
Pile (CBP) retaining wall is evaluated by using physical modeling
technique. Based on observations, the results of moment ratio
minimization method are in good agreement with the results of the
carried out physical modeling.
Abstract: This paper presents an approach for the classification of
an unstructured format description for identification of file formats.
The main contribution of this work is the employment of data mining
techniques to support file format selection with just the unstructured
text description that comprises the most important format features for
a particular organisation. Subsequently, the file format indentification
method employs file format classifier and associated configurations to
support digital preservation experts with an estimation of required file
format. Our goal is to make use of a format specification knowledge
base aggregated from a different Web sources in order to select file
format for a particular institution. Using the naive Bayes method,
the decision support system recommends to an expert, the file format
for his institution. The proposed methods facilitate the selection of
file format and the quality of a digital preservation process. The
presented approach is meant to facilitate decision making for the
preservation of digital content in libraries and archives using domain
expert knowledge and specifications of file formats. To facilitate
decision-making, the aggregated information about the file formats is
presented as a file format vocabulary that comprises most common
terms that are characteristic for all researched formats. The goal is to
suggest a particular file format based on this vocabulary for analysis
by an expert. The sample file format calculation and the calculation
results including probabilities are presented in the evaluation section.
Abstract: This research aims to develop an algorithm to
generate a schedule of multiple cranes that will maximize load
throughputs in anodizing operation. The algorithm proposed utilizes
an enumerative strategy to search for constant time between
successive loads and crane covering range over baths. The computer
program developed is able to generate a near-optimal crane schedule
within reasonable times, i.e. within 10 minutes. Its results are
compared with existing solutions from an aluminum extrusion
industry. The program can be used to generate crane schedules for
mixed products, thus allowing mixed-model line balancing to
improve overall cycle times.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: A pilot field study was conducted at the Jagjeetpur
Municipal Sewage treatment plant situated in the Haridwar town in
Uttarakhand state, India. The objectives of the present study were to
study the effect of treated wastewater on the production of various
paddy varieties (Sharbati, PR-114, PB-1, Menaka, PB1121 and PB
1509) and the emission of GHG gases (CO2, CH4 and N2O) as
compared to the same varieties grown in the control plots irrigated
with fresh water. Of late, the concept of water footprint assessment
has emerged, which explains enumeration of various types of water
footprints of an agricultural entity from its production to processing
stages. Paddy, the most water demanding staple crop of Uttarakhand
state, displayed a high green water footprint value of 2474.12 m3/
Ton. Most of the wastewater irrigated varieties displayed up to 6%
increase in production, except Menaka and PB-1121, which showed a
reduction in production (6% and 3% respectively), due to pest and
insect infestation. The treated wastewater was observed to be rich in
Nitrogen (55.94 mg/ml Nitrate), Phosphorus (54.24 mg/ml) and
Potassium (9.78 mg/ml), thus rejuvenating the soil quality and not
requiring any external nutritional supplements. A Percentage increase
of GHG gases of irrigation with treated municipal wastewater as
compared to control plots was observed as 0.4% - 8.6% (CH4), 1.1%
- 9.2% (CO2), and 0.07% - 5.8% (N2O). The variety, Sharbati,
displayed maximum production (5.5 ton/ha) and emerged as the most
resistant variety against pests and insects. The emission values of
CH4, CO2 and N2O were 729.31 mg/m2/d, 322.10 mg/m2/d and
400.21 mg/m2/d in water stagnant condition.
This study highlighted a successful possibility of reuse of
wastewater for non-potable purposes offering the potential for
exploiting this resource that can replace or reduce the existing use of
fresh water sources in agriculture sector.