Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: The paper focuses on the distance laboratory
organisation for training the electrical engineering staff and students
in the fields of electrical drive and power electronics. To support
online knowledge acquisition and professional enhancement, new
challenges in remote education based on an active learning approach
with self-assessment have been emerged by the authors. Following
the literature review and explanation of the improved assessment
methodology, the concept and technological basis of the labs
arrangement are presented. To decrease the gap between the distance
study of the up-to-date equipment and other educational activities in
electrical engineering, the improvements in the following-up the
learners’ progress and feedback composition are introduced. An
authoring methodology that helps to personalise knowledge
acquisition and enlarge Web-based possibilities is described.
Educational management based on self-assessment is discussed.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: Dietary cholesterol has elicited the most public
interest as it relates with coronary heart disease. Thus, humans have
been paying more attention to health, thereby reducing consumption
of cholesterol enriched food. Egg is considered as one of the major
sources of human dietary cholesterol. However, an alternative way to
reduce the potential cholesterolemic effect of eggs is to modify the
fatty acid composition of the yolk. The effect of palm oil (PO),
soybean oil (SO), sesame seed oil (SSO) and fish oil (FO)
supplementation in the diets of layers on egg yolk fatty acid,
cholesterol, egg production and egg quality parameters were
evaluated in a 42-day feeding trial. One hundred and five Isa Brown
laying hens of 34 weeks of age were randomly distributed into seven
groups of five replicates and three birds per replicate in a completely
randomized design. Seven corn-soybean basal diets (BD) were
formulated: BD+No oil (T1), BD+1.5% PO (T2), BD+1.5% SO (T3),
BD+1.5% SSO (T4), BD+1.5% FO (T5), BD+0.75% SO+0.75% FO
(T6) and BD+0.75% SSO+0.75% FO (T7). Five eggs were randomly
sampled at day 42 from each replicate to assay for the cholesterol,
fatty acid profile of egg yolk and egg quality assessment. Results
showed that there were no significant (P>0.05) differences observed
in production performance, egg cholesterol and egg quality
parameters except for yolk height, albumen height, yolk index, egg
shape index, haugh unit, and yolk colour. There were no significant
differences (P>0.05) observed in total cholesterol, high density
lipoprotein and low density lipoprotein levels of egg yolk across the
treatments. However, diets had effect (P
Abstract: Weak damping of low frequency oscillations is a frequent phenomenon in electrical power systems. These frequencies can be damped by power system stabilizers. Unified power flow controller (UPFC), as one of the most important FACTS devices, can be applied to increase the damping of power system oscillations and the more effect of this controller on increasing the damping of oscillations depends on its proper placement in power systems. In this paper, a technique based on controllability is proposed to select proper location of UPFC and the best input control signal in order to enhance damping of power oscillations. The effectiveness of the proposed technique is demonstrated in IEEE 9 bus power system.
Abstract: In this work, by replacing the traditional solid spokes with colloidal spokes, a vehicle wheel with a built-in suspension structure is proposed. Following the background and description of the wheel system, firstly, a vibration model of the wheel equipped with colloidal spokes is proposed, and based on such model the equivalent damping coefficients and spring constants are identified. Then, a modified model of a quarter-vehicle moving on a rough pavement is proposed in order to estimate the transmissibility of vibration from the road roughness to vehicle body. In the end, the optimal design of the colloidal spokes and the optimum number of colloidal spokes are decided in order to minimize the transmissibility of vibration, i.e., to maximize the ride comfort of the vehicle.
Abstract: This work aims to investigate the structure–property
relationship in ternary nanocomposites consisting of polypropylene
as the matrix, polyamide 66 as the minor phase and treated nanoclay
DELLITE 67G as the reinforcement. All PP/PA66/Nanoclay systems
with polypropylene grafted maleic anhydride PP-g-MAH as a
compatibilizer were prepared via melt compounding and
characterized in terms of nanoclay content. Morphological structure
was investigated by scanning electron microscopy. The rheological
behavior of the nanocomposites was determined by various methods,
viz melt flow index (MFI) and parallel plate rheological
measurements. The PP/PP-g-MAH/PA66 nanocomposites showed a homogeneous
morphology supporting the compatibility improvement between PP,
PA66, and nanoclay. SEM results revealed the formation of
nanocomposites as the nanoclay was intercalated and exfoliated. In
the ternary nanocomposites, the rheological behavior showed that, the
complex viscosity is increased with increasing the nanoclay. The results showed that the use of nanoclay affects the variations
of storage modulus (G′), loss modulus (G″) and the melt elasticity.
Abstract: We investigate the large scale of networks in the
context of network survivability under attack. We use appropriate
techniques to evaluate and the attacker-based- and the defenderbased-
network survivability. The attacker is unaware of the operated
links by the defender. Each attacked link has some pre-specified
probability to be disconnected. The defender choice is so that to
maximize the chance of successfully sending the flow to the
destination node. The attacker however will select the cut-set with
the highest chance to be disabled in order to partition the network.
Moreover, we extend the problem to the case of selecting the best p
paths to operate by the defender and the best k cut-sets to target by
the attacker, for arbitrary integers p,k>1. We investigate some
variations of the problem and suggest polynomial-time solutions.
Abstract: This paper presents the effects of mixing procedures
on mechanical properties of flyash-based geopolymer matrices
containing nanosilica (NS) at 0.5%, 1.0%, 2.0%, and 3.0% by weight.
Comparison is made with conventional mechanical dry-mixing of NS
with flyash and wet-mixing of NS in alkaline solutions. Physical and
mechanical properties are investigated using X-Ray Diffraction
(XRD) and Scanning Electron Microscope (SEM). Results show that
generally the addition of NS particles enhanced the microstructure
and improved flexural and compressive strengths of geopolymer
nanocomposites. However, samples, prepared using dry-mixing
approach, demonstrate better physical and mechanical properties
comparing to wet-mixing samples.
Abstract: One of prevailing modes of finance in emerging
Islamic banking system is Murabah’a. It means a financial dealing or
transaction in which seller tells cost of the goods to be sold to buyer.
Otherwise, the transaction would become invalid. In this mainstream,
import Murabah’a transaction is divergent in such a way that the cost
is not recognized and identified due to execution of import
transaction in foreign currency i.e. US Dollar and the next transaction
of Murabaha’a with the client is executed in local currency. Since this
transaction is executed in dual currency i.e. bank pays supplier in
foreign currency and executes Murabah’a with its client in local
currency and it is not allowed in according to Islamic Injunctions as
mentioned in hadith narrated by Hazrat Ibn-e-Umar (May Allah be
pleased with them) used to sell his camels with Dirhams and take
dinars instead and vice versa. Upon revealing before the Prophet
(Peace be upon him), he was advised that it must not be contingent in
the agreement and the ready rate would be applied and possession of
one of the consideration is compulsory. The solution in this regard is
that the import Murabah’a transaction should be in single currency
However, other currency can be paid in payment at the time of
payment in a very indispensable situation provided that ready rate
would be applied. Moreover, some of other solutions have also been
given in this regard.
Abstract: Low density polyethylene (LDPE) nanocomposites
with 3, 5 and 7 wt. % cobalt ferrite (CoFe2O4) nanopowder fabricated
with extrusion mixing and followed up by hot press to reach compact
samples. The transmission/reflection measurements were carried out
with a network analyzer in the frequency range of 8-12 GHz. By
increasing the percent of CoFe2O4 nanopowder, reflection loss (S11)
increases, while transferring loss (S21) decreases. Reflectivity (R)
calculations made using S11 and S21. Increase in percent of CoFe2O4
nanopowder up to 7 wt. % in composite leaded to higher reflectivity
amount, and revealed that increasing the percent of CoFe2O4
nanopowder up to 7 wt. % leads to further microwave absorption in
8-12 GHz range.
Abstract: Objective: Safety and efficacy of Ahmed glaucoma
valve implantation for the management of uveitis induced glaucoma
evaluated on the five dogs with uncontrollable glaucoma. Materials
and Methods: Ahmed Glaucoma Valve (AGV®; New World
Medical, Rancho Cucamonga, CA, USA) is a flow restrictive, nonobstructive
self-regulating valve system. Preoperative ocular
evaluation included direct ophthalmoscopy and measurement of the
intraocular pressure (IOP). The implant was examined and primed
prior to implantation. The selected site of the valve implantation was
the superior quadrant between the superior and lateral rectus muscles.
A fornix-based incision was made through the conjunectiva and
Tenon’s capsule. A pocket is formed by blunt dissection of Tenon’s
capsule from the episclera. The body of the implant was inserted into
the pocket with the leading edge of the device around 8-10 mm from
the limbus. Results: No post-operative complications were detected
in the operated eyes except a persistent corneal edema occupied the
upper half of the cornea in one case. Hyphaema was very mild and
seen only in two cases which resolved quickly two days after surgery.
Endoscopical evaluation for the operated eyes revealed a normal
ocular fundus with clearly visible optic papilla, tapetum and retinal
blood vessels. No evidence of hemorrhage, infection, adhesions or
retinal abnormalities was detected. Conclusion: Ahmed glaucoma
valve is safe and effective implant for treatment of uveitic glaucoma
in dogs.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: Despite the wide spread use of synthetic dyes, natural
dyes are still exploited and used to enhance its inherent aesthetic
qualities as a major material for beautification of the body. Centuries
before the discovery of synthetic dyes, natural dyes were the only
source of dye open to mankind. Dyes are extracted from plant -
leaves, roots and barks, insect secretions, and minerals. However,
research findings have made it clear that of all, plants- leaves, roots,
barks or flowers are the most explored and exploited in which henna
(Lawsonia innermis L.) is one of those plants. Experiment has also
shown that henna is used in body painting in conjunction with an
alkaline (Ammonium Sulphate) as a fixing agent. This of course
gives a clue that if colour derived from henna is properly
investigated, it may not only be used for body decoration but
possibly, may have affinity to fiber substrate. This paper investigates
the dyeing potentials – dye ability and fastness qualities of henna dye
extracts on cotton and linen fibers using mordants like ammonium
sulphate and other alkalis (hydrosulphate and caustic soda, potash,
common salt, potassium alum). Hot and cold water and ethanol
solvent were used in the extraction of the dye to investigate the most
effective method, dye ability, and fastness qualities of these extracts
under room temperature. The results of the experiment show that
cotton have a high rate of dye intake than other fiber. On a similar
note, the colours obtained depend most on the solvent used. In
conclusion, hot water extraction appears more effective. While the
colours obtained from ethanol and both cold hot methods of
extraction range from light to dark yellow, light green to army green
and to some extent shades of brown hues.
Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: The nutritional composition and hypoglycaemic effect
of crackers produced from blend of sprouted pigeon pea, unripe
plantain and brewers’ spent grain and fed to Alloxan induced diabetic
rat was investigated. Crackers were produced from different blends of
sprouted pigeon pea, unripe plantain and brewers’ spent grain. The
crackers were evaluated for proximate composition, amino acid
profile and antinutritional factors. Blood glucose levels of normal and
diabetic rats fed with the control sample and different formulations of
cracker were measured. The protein content of the samples were
significantly different (p
Abstract: This research work is an experimental study, through
development of an adhesive from Prosopis africana endosperm. The
prosopis seed for this work were obtained from Enugu State in the
South East part of Nigeria. The seeds were prepared by separating the
endosperm from the seed coat and cotyledon. Three methods were
used to separate them, which are acidic method, roasting method and
boiling method. 20g of seed were treated with different
concentrations (25, 40, 55, 70, and 85% w/w) at 100°C and constant
time (30 minutes), under continuous stirring with magnetic stirrer.
Also 20g of seed were treated with sulphuric acid of concentrations
40% w/w at 100°C with different time (10, 15, 20, 25, 30 minutes),
under continuous stirring with magnetic stirrer. Finally, 20g of seed
were treated with sulphuric acid of concentrations 40% w/w at
different temperature (20°C, 40°C, 60°C, 80°C, and 100°C) with
constant time (30 minutes), under continuous stirring with magnetic
stirrer. The whole endosperm extracted was adhesive. The physical
properties of the adhesive were determined (appearance, odour, taste,
solubility, pH, size, and binding strength). The percentage of the
adhesive yield makes the commercialization of the seed in Nigeria
possible and profitable. The very high viscosity attained at low
concentrations makes prosopis adhesive an excellent thickener in the
food industry.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.