Abstract: This paper analyses the torsional efforts in gas turbine-generator shafts caused by high speed automatic reclosing of transmission lines. This issue is especially important for cases of three phase short circuit and unsuccessful reclosure of lines in the vicinity of the thermal plant. The analysis was carried out for the thermal plant TERMOPERNAMBUCO located on Northeast region of Brazil. It is shown that stress level caused by lines unsuccessful reclosing can be several times higher than terminal three-phase short circuit. Simulations were carried out with detailed shaft torsional model provided by machine manufacturer and with the “Alternative Transient Program – ATP" program [1]. Unsuccessful three phase reclosing for selected lines in the area closed to the plant indicated most critical cases. Also, reclosing first the terminal next to the gas turbine gererator will lead also to the most critical condition. Considering that the values of transient torques are very sensible to the instant of reclosing, simulation of unsuccessful reclosing with statistics ATP switch were carried out for determination of most critical transient torques for each section of the generator turbine shaft.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.
Abstract: Mixed Model Production is the practice of assembling
several distinct and different models of a product on the same
assembly line without changeovers and then sequencing those models
in a way that smoothes the demand for upstream components. In this
paper, we consider an objective function which minimizes total
stoppage time and total idle time and it is presented sequence
dependent set up time. Many studies have been done on the mixed
model assembly lines. But in this paper we specifically focused on
reducing the idle times. This is possible through various help policies.
For improving the solutions, some cases developed and about 40 tests
problem was considered. We use scatter search for optimization and
for showing the efficiency of our algorithm, experimental results
shows behavior of method. Scatter search and help policies can
produce high quality answers, so it has been used in this paper.
Abstract: Heuristics-based search methodologies normally
work on searching a problem space of possible solutions toward
finding a “satisfactory" solution based on “hints" estimated from the
problem-specific knowledge. Research communities use different
types of methodologies. Unfortunately, most of the times, these hints
are immature and can lead toward hindering these methodologies by
a premature convergence. This is due to a decrease of diversity in
search space that leads to a total implosion and ultimately fitness
stagnation of the population. In this paper, a novel Decision Maturity
framework (DMF) is introduced as a solution to this problem. The
framework simply improves the decision on the direction of the
search by materializing hints enough before using them. Ideas from
this framework are injected into the particle swarm optimization
methodology. Results were obtained under both static and dynamic
environment. The results show that decision maturity prevents
premature converges to a high degree.
Abstract: The usual method of river flow diversion involves construction of tunnels and cofferdams. Given the fact that the cost of diversion works could be as high as 10-20% of the total dam construction cost, due attention should be paid to optimum design of the diversion works. The cost of diversion works depends, on factors, such as: the tunnel dimensions and the intended tunneling support measures during and after excavation; quality and characterizes of the rock through which the tunnel should be excavated; the dimensions of the upstream (and downstream) cofferdams; and the magnitude of river flood the system is designed to divert. In this paper by use of the cost of unit prices for tunnel excavation, tunnel lining, tunnel support (rock bolt + shotcrete) and cofferdam fill the cost function was determined. The function is then minimized by the aid of PSO Algorithm (particle swarm optimization). It is found that the optimum diameter and the total diversion cost are directly related to the river flood discharge (Q). It has also shown that in addition to optimum diameter design discharge (Q), river length, tunnel length, is mainly a function of the ratios (not the absolute values) of the unit prices and does not depend on the overall price levels in the respective country. The results of optimization use in some of the case study lead us to significant changes in the cost.
Abstract: Via a large scale cross-sectional study among Japanese white color workers, the authors aimed to elucidate: (1) the distributions of Sense of Coherence (SOC), which reflect stress coping abilities, (2) the distributions of Life experience; (3) and the association between SOC and Life experience. Anonymous self-administered questionnaires were sent to 15,891 in 2001 and 21,922 in 2011 employees at educational and research institutions in Tsukuba Research Park City. A total of 5,868 (36.9%) and 9,528 (43.5%) respectively workers completed and returned the questionnaire; 5,715 and 9,515 respectively workers without missing data were analyzed. SOC scale scores differed by gender, age, and other demographic features in both study years. Among the life experiences, workers who have got over parenting or management position were higher SOC scale scores adjusted by gender and age. The life experiences that workers have got over could develop their stronger SOC in their life course.
Abstract: Sexual behavior and semen charactertistics were
evaluated in young male Boer goats in tropical condition during time
period of September to November 2009. The animal was let to have
adaptation for five months after importation from Australian climate.
A total of 20 bucks were observed for sexual behavior and ability of
semen production. Out of this number, 4 faild to libido and 3
produced poor semen. The remaing 13 animals were divided into
three groups according to the ages (11-13, 15-16 and 18-25 months).
Sexual behavior consisting response time to female teaser,
ejaculation time, fixing strenght to female and erection status were
normaly observer in 13 bucks, and there was no significant difference
between age groups. Semen characteristics from 13 bucks were in
normal quality in the volume, sperm mass motility, individual
motility, percentage of live- and abnormal sperm. We concluded that
is possible to collect semen of Boer goats during the period of
September to November under tropical condition. Collection during
other time period should be analyzed.
Abstract: This paper propose the robust character segmentation method for license plate with topological transform such as twist,rotation. The first step of the proposed method is to find a candidate region for character and license plate. The character or license plate
must be appeared as closed loop in the edge image. In the case of
detecting candidate for character region, the evaluation of detected
region is using topological relationship between each character. When
this method decides license plate candidate region, character features
in the region with binarization are used. After binarization for the detected candidate region, each character region is decided again. In
this step, each character region is fitted more than previous step. In the
next step, the method checks other character regions with different
scale near the detected character regions, because most license plates
have license numbers with some meaningful characters around them.
The method uses perspective projection for geometrical normalization.
If there is topological distortion in the character region, the method
projects the region on a template which is defined as standard license
plate using perspective projection. In this step, the method is able to
separate each number region and small meaningful characters. The
evaluation results are tested with a number of test images.
Abstract: Optimal selection of electrical insulations in electrical
machinery insures reliability during operation. From the insulation
studies of view for electrical machines, stator is the most important
part. This fact reveals the requirement for inspection of the electrical
machine insulation along with the electro-thermal stresses. In the
first step of the study, a part of the whole structure of machine in
which covers the general characteristics of the machine is chosen,
then based on the electromagnetic analysis (finite element method),
the machine operation is simulated. In the simulation results, the
temperature distribution of the total structure is presented
simultaneously by using electro-thermal analysis. The results of
electro-thermal analysis can be used for designing an optimal cooling
system. In order to design, review and comparing the cooling
systems, four wiring structures in the slots of Stator are presented.
The structures are compared to each other in terms of electrical,
thermal distribution and remaining life of insulation by using Finite
Element analysis. According to the steps of the study, an optimization
algorithm has been presented for selection of appropriate structure.
Abstract: This study proposes a hybrid minimal repair policy
which combines periodic maintenance policy with age-based maintenance policy for a serial production system. Parameters of such policy are defined as and which indicate as hybrid minimal
repair time and planned preventive maintenance time
respectively . Under this hybrid policy, the system is
repaired minimally if it fails during , . A perfect repair is
conducted on the first failure after at any machines. At the same time, we take opportunity to advance the preventive maintenance of
other machines simultaneously. If the system is still operating
properly up to , then the preventive maintenance is carried out as its
predetermined schedule. For a given , we obtain the optimal value which minimizes the expected cost per time unit. Numerical
example is presented to illustrate the properties of the optimal solution.
Abstract: Recently, the issue of machine condition monitoring
and fault diagnosis as a part of maintenance system became global
due to the potential advantages to be gained from reduced
maintenance costs, improved productivity and increased machine
availability. The aim of this work is to investigate the effectiveness
of a new fault diagnosis method based on power spectral density
(PSD) of vibration signals in combination with decision trees and
fuzzy inference system (FIS). To this end, a series of studies was
conducted on an external gear hydraulic pump. After a test under
normal condition, a number of different machine defect conditions
were introduced for three working levels of pump speed (1000, 1500,
and 2000 rpm), corresponding to (i) Journal-bearing with inner face
wear (BIFW), (ii) Gear with tooth face wear (GTFW), and (iii)
Journal-bearing with inner face wear plus Gear with tooth face wear
(B&GW). The features of PSD values of vibration signal were
extracted using descriptive statistical parameters. J48 algorithm is
used as a feature selection procedure to select pertinent features from
data set. The output of J48 algorithm was employed to produce the
crisp if-then rule and membership function sets. The structure of FIS
classifier was then defined based on the crisp sets. In order to
evaluate the proposed PSD-J48-FIS model, the data sets obtained
from vibration signals of the pump were used. Results showed that
the total classification accuracy for 1000, 1500, and 2000 rpm
conditions were 96.42%, 100%, and 96.42% respectively. The results
indicate that the combined PSD-J48-FIS model has the potential for
fault diagnosis of hydraulic pumps.
Abstract: The approaches to make an agent generate intelligent actions in the AI field might be roughly categorized into two ways–the classical planning and situated action system. It is well known that each system have its own strength and weakness. However, each system also has its own application field. In particular, most of situated action systems do not directly deal with the logical problem. This paper first briefly mentions the novel action generator to situatedly extract a set of actions, which is likely to help to achieve the goal at the current situation in the relaxed logical space. After performing the action set, the agent should recognize the situation for deciding the next likely action set. However, since the extracted action is an approximation of the action which helps to achieve the goal, the agent could be caught into the deadlock of the problem. This paper proposes the newly developed hybrid architecture to solve the problem, which combines the novel situated action generator with the conventional planner. The empirical result in some planning domains shows that the quality of the resultant path to the goal is mostly acceptable as well as deriving the fast response time, and suggests the correlation between the structure of problems and the organization of each system which generates the action.
Abstract: Potassium monopersulfate has been decomposed in aqueous solution in the presence of Co(II). The process has been simulated by means of a mechanism based on elementary reactions. Rate constants have been taken from literature reports or, alternatively, assimilated to analogous reactions occurring in Fenton's chemistry. Several operating conditions have been successfully applied.
Abstract: Culinary culture differences can cause health
problems for international tourists in Thailand. This paper drew upon
data collected from an international tourist survey conducted in
Bangkok, Thailand during summer of 2012. Summer is the period
that a variety food safety issues and incidents are often publicized in
Thailand. The survey targeted European Union tourists- concerns
toward a variety of food safety issues that they encountered during
their trip in Thailand. A total of 400 respondents were elicited as data
input for t-test, and one way ANOVA test. The findings revealed an
astonishing result that up to 46.5 percent of respondents were sick at
least one time or more in Thailand. However, the majority of
respondents trusted that the Thai hotel and Thai restaurants would
ensure food safety, but they did not trust street vendors to ensure food
safety. The level of food safety concern can be ranked from most
concern to least concern by using the value of mean scores as
follows: 1) artificial coloring, 2) use of preservatives, 3) antibiotics,
4) growth hormones, 5) chemical residues, and 6) bacterial
contamination. The overall mean score for level of concerns was
3.493 with standard deviation of 1.677 which did not indicate a very
high level of concern. In addition, the result for t-test and one way
ANOVA test revealed that there was not much effect from the
demographic differences to level of food safety concerns.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: One of the vital developmental tasks that an
individual faces during adolescence is choosing a career. Arriving at
a career decision is difficult and anxious for many adolescents in the
tertiary level. The main purpose of this study is to determine the
factors relating to career indecision among freshmen college students
as basis for the formulation of a comprehensive career counseling
program for the psychological well-being of freshmen university
students. The subjects were purposively selected. The Slovin-s
formula was used in determining the sample size, using a 0.05
margin of error in getting the total number of samples per college and
per major. The researcher made use of descriptive correlational study
in determining significant factors relating to career indecision.
Multiple Regression Analysis indicated that career thoughts, career
decisions and vocational identity as factors related to career
indecision.
Abstract: This paper examines and compares several of the most common real time methods. These methods are CORE, YSM, MASCOT, JSD, DARTS, RTSAD, ADARTS, CODARTS, HOOD, HRT-HOOD, ROOM, UML, UML-RT. The methods are compared using attributes like i) usability, ii) compositionality and iii) proper RT notations available. Finally some comparison results are given and discussed.