Abstract: This paper applied factor conditions from Porter’s
Diamond Model (1990) to understand the various challenges facing
the AMISA. Factor conditions highlighted in Porter’s model are
grouped into two groups namely, basic and advance factors. Two
AMISA associations representing over 10 000 employees were
interviewed. The largest Clothing, Textiles and Leather (CTL)
apparel retail group was also interviewed with a government
department implementing the industrialization policy were
interviewed. The paper points out that AMISA have basic factor conditions
necessary for competitive advantage in the apparel industries.
However advance factor creation has proven to be a challenge for
AMISA, Higher Education Institutions (HEIs) and government. Poor
infrastructural maintenance has contributed to high manufacturing
costs and poor quick response technologies. The use of Porter’s
Factor Conditions as a tool to analyze the sector’s competitive
advantage challenges and opportunities has increased knowledge
regarding factors that limit the AMISA’s competitiveness. It is
therefore argued that other studies on Porter’s Diamond model
factors like Demand conditions, Firm strategy, structure and rivalry
and Related and supporting industries can be used to analyze the
situation of the AMISA for the purposes of improving competitive
advantage.
Abstract: Drying is a phenomenon that accompanies the
hardening of hydraulic materials. This study is concerned the
modelling of drying shrinkage of the hydraulic materials and the
prediction of the rate of spontaneous deformations of hydraulic
materials during hardening. The model developed takes consideration
of the main factors affecting drying shrinkage. There was agreement
between drying shrinkage predicted by the developed model and
experimental results. In last we show that developed model describe
the evolution of the drying shrinkage of high performances concretes
correctly.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.
Abstract: This paper presents the design process of a high
performance 3-phase 3.7 kW 2-pole line start permanent magnet
synchronous motor for pumping system. A method was proposed to
study the starting torque characteristics considering line start with
high inertia load. A d-q model including cage was built to study the
synchronization capability. Time-stepping finite element method
analysis was utilized to accurately predict the dynamic and transient
performance, efficiency, starting current, speed curve and etc.
Considering the load torque of pumps during starting stage, the rotor
bar was designed with minimum demagnetization of permanent
magnet caused by huge starting current.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: This paper introduces a boost converter with a new
active snubber cell. In this circuit, all of the semiconductor
components in the converter softly turns on and turns off with the
help of the active snubber cell. Compared to the other converters, the
proposed converter has advantages of size, number of components
and cost. The main feature of proposed converter is that the extra
voltage stresses do not occur on the main switches and main diodes.
Also, the current stress on the main switch is acceptable level.
Moreover, the proposed converter can operates under light load
conditions and wide input line voltage. In this study, the operating
principle of the proposed converter is presented and its operation is
verified with the Proteus simulation software for a 1 kW and 100 kHz
model.
Abstract: This article presents a vibration diagnostic method
designed for Permanent Magnets (PM) electrical machines–traction
motors and generators. Those machines are commonly used in traction
drives of electrical vehicles and small wind or water systems. The
described method is very innovative and unique. Specific structural
properties of machines excited by permanent magnets are used in this
method - electromotive force (EMF) generated due to vibrations. There
was analyzed number of publications, which describe vibration
diagnostic methods, and tests of electrical machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. This work presents field-circuit model,
results of static tests, results of calculations and simulations.
Abstract: This paper presents modeling and simulation of
flexible robot in an underwater environment. The underwater
environment completely contrasts with ground or space environment.
The robot in an underwater situation is subjected to various dynamic
forces like buoyancy forces, hydrostatic and hydrodynamic forces.
The underwater robot is modeled as Rayleigh beam. The developed
model further allows estimating the deflection of tip in two
directions. The complete dynamics of the underwater robot is
analyzed, which is the main focus of this investigation. The control of
robot trajectory is not discussed in this paper. Simulation is
performed using Symbol Shakti software.
Abstract: Application of biochar to arable soils represents a new
approach to restore soil health and quality. Many studies reported the
positive effect of biochar application on soil fertility and
development of soil microbial community. Moreover biochar may
affect the soil water retention, but this effect has not been sufficiently
described yet. Therefore this study deals with the influence of
biochar application on: microbial activities in soil, availability of
mineral nitrogen in soil for microorganisms, mineral nitrogen
retention and plant production. To demonstrate the effect of biochar
addition on the above parameters, the pot experiment was realized.
As a model crop, Lactuca sativa L. was used and cultivated from
December 10th 2014 till March 22th 2015 in climate chamber in
thoroughly homogenized arable soil with and without addition of
biochar. Five variants of experiment (V1 – V5) with different regime
of irrigation were prepared. Variants V1 – V2 were fertilized by
mineral nitrogen, V3 – V4 by biochar and V5 was a control. The
significant differences were found only in plant production and
mineral nitrogen retention. The highest content of mineral nitrogen
in soil was detected in V1 and V2, about 250 % in comparison with
the other variants. The positive effect of biochar application on soil
fertility, mineral nitrogen availability was not found. On the other
hand results of plant production indicate the possible positive effect
of biochar application on soil water retention.
Abstract: The current paper presents an extensive bottom-up
framework for assessing building sector-specific vulnerability to
climate change: energy supply and demand. The research focuses on
the application of downscaled seasonal models for estimating energy
performance of buildings in Greece. The ARW-WRF model has
been set-up and suitably parameterized to produce downscaled
climatological fields for Greece, forced by the output of the CFSv2
model. The outer domain, D01/Europe, included 345 x 345 cells of
horizontal resolution 20 x 20 km2 and the inner domain, D02/Greece,
comprised 180 x 180 cells of 5 x 5 km2 horizontal resolution. The
model run has been setup for a period with a forecast horizon of 6
months, storing outputs on a six hourly basis.
Abstract: Residential block construction of big cities in China
began in the 1950s, and four models had far-reaching influence on
modern residential block in its development process, including unit
compound and residential district in 1950s to 1980s, and gated
community and open community in 1990s to now. Based on analysis
of the four models’ fabric, the article takes residential blocks in
Hangzhou west area as an example and carries on the studies from
urban structure level and block spacial level, mainly including urban
road network, land use, community function, road organization, public
space and building fabric. At last, the article puts forward “Semi-open
Sub-community” strategy to improve the current fabric.
Abstract: High Order Thinking Skills (HOTS) are suggested
today as essential for the cognitive development of students and as
preparing them for real life skills. Teachers are encouraged to use
HOTS activities in the classroom to help their students develop
higher order skills and deep thinking. So it is essential to prepare preservice
teachers to write and use HOTS activities for their students.
This paper describes a model for integrating HOTS activities with
GeoGebra in pre-service teachers’ preparation. This model describes
four aspects of HOTS activities and working with them: activity
components, preparation procedure, strategies and processes used in
writing a HOTS activity and types of the HOTS activities. In
addition, the paper describes the pre-service teachers' difficulties in
preparing and working with HOTS activities, as well as their
perceptions regarding the use of these activities and GeoGebra in the
mathematics classroom. The paper also describes the contribution of
a HOTS activity to pupils' learning of mathematics, where this HOTS
activity was prepared and taught by one pre-service teacher.
Abstract: The output error of the globoidal cam mechanism can
be considered as a relevant indicator of mechanism performance,
because it determines kinematic and dynamical behavior of
mechanical transmission. Based on the differential geometry and the
rigid body transformations, the mathematical model of surface
geometry of the globoidal cam is established. Then we present the
analytical expression of the output error (including the transmission
error and the displacement error along the output axis) by considering
different manufacture and assembly errors. The effects of the center
distance error, the perpendicular error between input and output axes
and the rotational angle error of the globoidal cam on the output error
are systematically analyzed. A globoidal cam mechanism which is
widely used in automatic tool changer of CNC machines is applied for
illustration. Our results show that the perpendicular error and the
rotational angle error have little effects on the transmission error but
have great effects on the displacement error along the output axis. This
study plays an important role in the design, manufacture and assembly
of the globoidal cam mechanism.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: A robust sequential nonparametric method is proposed
for adaptation to background noise parameters for real-time. The
distribution of background noise was modelled like to Huber
contamination mixture. The method is designed to operate as an
adaptation-unit, which is included inside a detection subsystem of an
integrated multichannel monitoring system. The proposed method
guarantees the given size of a nonasymptotic confidence set for noise
parameters. Properties of the suggested method are rigorously
proved. The proposed algorithm has been successfully tested in real
conditions of a functioning C-OTDR monitoring system, which was
designed to monitor railways.
Abstract: This paper shows the general perceptions of Spanish
university stakeholders in relation to the university’s annual reports
and the adequacy and potential of intellectual capital reporting. To
this end, a questionnaire was designed and sent to every member of
the Social Councils of Spanish public universities. It was thought that
these participants would provide a good example of the attitude of
university stakeholders since they represent the different social
groups connected with universities. From the results of this study we
are in the position of confirming the need for universities to offer
information on intellectual capital in their accounting information
model.
Abstract: This paper presents an approach of on-line control of
the state of technosphere and environment objects based on the
integration of Data Warehouse, OLAP and Expert systems
technologies. It looks at the structure and content of data warehouse
that provides consolidation and storage of monitoring data. There is a
description of OLAP-models that provide a multidimensional
analysis of monitoring data and dynamic analysis of principal
parameters of controlled objects. The authors suggest some criteria of
emergency risk assessment using expert knowledge about danger
levels. It is demonstrated now some of the proposed solutions could
be adopted in territorial decision making support systems.
Operational control allows authorities to detect threat, prevent natural
and anthropogenic emergencies and ensure a comprehensive safety of
territory.