Abstract: Titanium dioxide coatings were deposited by utilizing
atmospheric plasma spraying (APS) system. The agglomerated nanopowder
and different spraying parameters were used to determine
their influences on the microstructure surface feature and photoabsorption
of the coatings. The microstructure of as-sprayed TiO2
coatings were characterized by scanning electron microscope (SEM).
Surface characteristics were investigated by Fourier Transform
Infrared (FT-IR). The photo absorption was determined by UV-VIS
spectrophotometer. It is found that the spray parameters have an
influence on the microstructure, surface feature and photo-absorption
of the TiO2 coatings.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: An Advance Driver Assistance System (ADAS) is a computer system on board a vehicle which is used to reduce the risk of vehicular accidents by monitoring factors relating to the driver, vehicle and environment and taking some action when a risk is identified. Much work has been done on assessing vehicle and environmental state but there is still comparatively little published work that tackles the problem of driver state. Visual attention is one such driver state. In fact, some researchers claim that lack of attention is the main cause of accidents as factors such as fatigue, alcohol or drug use, distraction and speeding all impair the driver-s capacity to pay attention to the vehicle and road conditions [1]. This seems to imply that the main cause of accidents is inappropriate driver behaviour in cases where the driver is not giving full attention while driving. The work presented in this paper proposes an ADAS system which uses an image based template matching algorithm to detect if a driver is failing to observe particular windscreen cells. This is achieved by dividing the windscreen into 24 uniform cells (4 rows of 6 columns) and matching video images of the driver-s left eye with eye-gesture templates drawn from images of the driver looking at the centre of each windscreen cell. The main contribution of this paper is to assess the accuracy of this approach using Receiver Operating Characteristic analysis. The results of our evaluation give a sensitivity value of 84.3% and a specificity value of 85.0% for the eye-gesture template approach indicating that it may be useful for driver point of regard determinations.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: This paper explores an application of an adaptive learning mechanism for robots based on the natural immune system. Most of the research carried out so far are based either on the innate or adaptive characteristics of the immune system, we present a combination of these to achieve behavior arbitration wherein a robot learns to detect vulnerable areas of a track and adapts to the required speed over such portions. The test bed comprises of two Lego robots deployed simultaneously on two predefined near concentric tracks with the outer robot capable of helping the inner one when it misaligns. The helper robot works in a damage-control mode by realigning itself to guide the other robot back onto its track. The panic-stricken robot records the conditions under which it was misaligned and learns to detect and adapt under similar conditions thereby making the overall system immune to such failures.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: This paper reports on a survey of state-of-the-art
application scenarios for smart office environments. Based on an
analysis of ongoing research activities and industry projects,
functionalities and services of future office systems are extracted. In
a second step, these results are used to identify the key characteristics
of emerging products.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: In this paper, FinFET devices are analyzed with
emphasis on sub-threshold leakage current control. This is achieved
through proper biasing of the back gate, and through the use of
asymmetric work functions for the four terminal FinFET devices. We
are also examining different configurations of multiplexers and XOR
gates using transistors of symmetric and asymmetric work functions.
Based on extensive characterization data for MUX circuits, our
proposed configuration using symmetric devices lead to leakage
current and delay improvements of 65% and 47% respectively
compared to results in the literature. For XOR gates, a 90%
improvement in the average leakage current is achieved by using
asymmetric devices. All simulations are based on a 25nm FinFET
technology using the University of Florida UFDG model.
Abstract: In the past 20 years the economy of the Czech
Republic has experienced substantial changes. In the 1990s the
development was affected by the transformation which sought to
establish the right conditions for privatization and creation of
elementary market relations. In the last decade the characteristic
elements such as private ownership and corresponding institutional
framework have been strengthened. This development was marked by
the accession of the Czech Republic to the EU. The Czech Republic
is striving to reduce the difference between its level of economic
development and the quality of institutional framework in
comparison with other developed countries. The process of finding
the adequate solutions has been hampered by the negative impact of
the world financial crisis on the Czech Republic and the standard of
living of its inhabitants. This contribution seeks to address the
question of whether and to which extent the economic development
of the transitive Czech economy is affected by the change in
behaviour of households and their tendency to consumption, i.e. in
the sense of reduction or increase in demand for goods and services.
It aims to verify whether the increasing trend of household
indebtedness and decreasing trend of saving pose a significant risk in
the Czech Republic. At a general level the analysis aims to contribute
to finding an answer to the question of whether the debt increase of
Czech households is connected to the risk of "eating through" the
borrowed money and whether Czech households risk falling into a
debt trap. In addition to household indebtedness risks in the Czech
Republic the analysis will focus on identification of specifics of the
transformation phase of the Czech economy in comparison with the
EU countries, or selected OECD countries.
Abstract: In this study, hydrogels consisted of polyvinyl alcohol,
propylene glycol and β-glucan were developed by radiation technique
for wound dressing. The prepared hydrogels were characterized by
examining of physical properties such as gel fraction and absorption
ratio. The gel fraction and absorption ratio were dependent on the
crosslinking density. On observing the wound healing of rat skin, the
resulting hydrogels accelerated the wound healing comparing to cotton
gauze. Therefore, the PVA/propylene glycol/β-glucan blended
hydrogels can greatly accelerate the healing without causing irritation.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: Mobile ad-hoc networks (MANETs) are a form of
wireless networks which do not require a base station for providing
network connectivity. Mobile ad-hoc networks have many
characteristics which distinguish them from other wireless networks
which make routing in such networks a challenging task. Cluster
based routing is one of the routing schemes for MANETs in which
various clusters of mobile nodes are formed with each cluster having
its own clusterhead which is responsible for routing among clusters.
In this paper we have proposed and implemented a distributed
weighted clustering algorithm for MANETs. This approach is based
on combined weight metric that takes into account several system
parameters like the node degree, transmission range, energy and
mobility of the nodes. We have evaluated the performance of
proposed scheme through simulation in various network situations.
Simulation results show that proposed scheme outperforms the
original distributed weighted clustering algorithm (DWCA).
Abstract: Currently is characterized production engineering
together with the integration of industrial automation and robotics
such very quick view of to manufacture the products. The production
range is continuously changing, expanding and producers have to be
flexible in this regard. It means that need to offer production
possibilities, which can respond to the quick change. Engineering
product development is focused on supporting CAD software, such
systems are mainly used for product design. That manufacturers are
competitive, it should be kept procured machines made available
capable of responding to output flexibility. In response to that
problem is the development of flexible manufacturing systems,
consisting of various automated systems. The integration of flexible
manufacturing systems and subunits together with product design and
of engineering is a possible solution for this issue. Integration is
possible through the implementation of CIM systems. Such a solution
and finding a hyphen between CAD and procurement system ICIM
3000 from Festo Co. is engaged in the research project and this
contribution. This can be designed the products in CAD systems and
watch the manufacturing process from order to shipping by the
development of methods and processes of integration, This can be
modeled in CAD systems products and watch the manufacturing
process from order to shipping to develop methods and processes of
integration, which will improve support for product design
parameters by monitoring of the production process, by creating of
programs for production using the CAD and therefore accelerates the
a total of process from design to implementation.
Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: The present study attempted to improve the Mercury
(Hg) sorption capacity of kanuma volcanic ash soil (KVAS) by
impregnating the cupper (Cu). Impregnation was executed by 1 and
5% Cu powder and sorption characterization of optimum Hg
removing Cu impregnated KVAS was performed under different
operational conditions, contact time, solution pH, sorbent dosage and
Hg concentration using the batch operation studies. The 1% Cu
impregnated KVAS pronounced optimum improvement (79%) in
removing Hg from water compare to control. The present
investigation determined the equilibrium state of maximum Hg
adsorption at 6 h contact period. The adsorption revealed a pH
dependent response and pH 3.5 showed maximum sorption capacity
of Hg. Freundlich isotherm model is well fitted with the experimental
data than that of Langmuir isotherm. It can be concluded that the Cu
impregnation improves the Hg sorption capacity of KVAS and 1%
Cu impregnated KVAS could be employed as cost-effective
adsorbent media for treating Hg contaminated water.
Abstract: This paper presents a research agenda on the SCOR
model adaptation. SCOR model is designated to measure supply
chain performance and logistics impact across the boundaries of
individual organizations. It is at its growing stage of its life cycle and
is enjoying the leverage of becoming the industry standard. The
SCOR model has been developed and used widely in developed
countries context. This research focuses on the SCOR model
adaptation for the manufacturing industry in developing countries.
With a necessary understanding of the characteristics, difficulties and
problems of the manufacturing industry in developing countries-
supply chain; consequently, we will try to designs an adapted model
with its building blocks: business process model, performance
measures and best practices.