Abstract: In this paper, the dynamic characteristics of a threelobe
journal bearing lubricated with micropolar fluids are determined
by the linear stability theory. Lubricating oil containing additives and
contaminants is modelled as micropolar fluid. The modified
Reynolds equation is obtained using the micropolar lubrication theory
.The finite difference technique has been used to determine the
solution of the modified Reynolds equation. The dynamic
characteristics in terms of stiffness, damping coefficients, the critical
mass and whirl ratio are determined for various values of size of
material characteristic length and the coupling number. The
computed results show that the three-lobe bearing lubricated with
micropolar fluid exhibits better stability compared with that
lubricated with Newtonian fluid. According to the results obtained,
the effect of the parameter micropolar fluid is remarkable on the
dynamic characteristics and stability of the three-lobe bearing.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: The paper presents a plastic analysis procedure based
on the energy balance concept for performance based seismic retrofit
of multi-story multi-bay masonry infilled reinforced concrete (R/C)
frames with a ‘soft’ ground story using passive energy dissipation
(PED) devices with the objective of achieving a target performance
level of the retrofitted R/C frame for a given seismic hazard level at
the building site. The proposed energy based plastic analysis
procedure was employed for developing performance based design
(PBD) formulations for PED devices for a simulated application in
seismic retrofit of existing frame structures designed in compliance
with the prevalent standard codes of practice. The PBD formulations
developed for PED devices were implemented for simulated seismic
retrofit of a representative code-compliant masonry infilled R/C
frame with a ‘soft’ ground story using friction dampers as the PED
device. Non-linear dynamic analyses of the retrofitted masonry
infilled R/C frames is performed to investigate the efficacy and
accuracy of the proposed energy based plastic analysis procedure in
achieving the target performance level under design level
earthquakes. Results of non-linear dynamic analyses demonstrate that
the maximum inter-story drifts in the masonry infilled R/C frames
with a ‘soft’ ground story that is retrofitted with the friction dampers
designed using the proposed PBD formulations are controlled within
the target drifts under near-field as well far-field earthquakes.
Abstract: In this paper, Fuzzy C-Means clustering with
Expectation Maximization-Gaussian Mixture Model based hybrid
modeling algorithm is proposed for Continuous Tamil Speech
Recognition. The speech sentences from various speakers are used
for training and testing phase and objective measures are between the
proposed and existing Continuous Speech Recognition algorithms.
From the simulated results, it is observed that the proposed algorithm
improves the recognition accuracy and F-measure up to 3% as
compared to that of the existing algorithms for the speech signal from
various speakers. In addition, it reduces the Word Error Rate, Error
Rate and Error up to 4% as compared to that of the existing
algorithms. In all aspects, the proposed hybrid modeling for Tamil
speech recognition provides the significant improvements for speechto-
text conversion in various applications.
Abstract: This paper investigates the joint effect of the
interconnected (n,k)-star network topology and Multi-Agent
automated control on restoration and reconfiguration of power
systems. With the increasing trend in development in Multi-Agent
control technologies applied to power system reconfiguration
in presence of faulty components or nodes. Fault tolerance is
becoming an important challenge in the design processes of the
distributed power system topology. Since the reconfiguration of a
power system is performed by agent communication, the (n,k)-star
interconnected network topology is studied and modeled in this
paper to optimize the process of power reconfiguration. In this paper,
we discuss the recently proposed (n,k)-star topology and examine its
properties and advantages as compared to the traditional multi-bus
power topologies. We design and simulate the topology model for
distributed power system test cases. A related lemma based on the
fault tolerance and conditional diagnosability properties is presented
and proved both theoretically and practically. The conclusion is
reached that (n,k)-star topology model has measurable advantages
compared to standard bus power systems while exhibiting fault
tolerance properties in power restoration, as well as showing
efficiency when applied to power system route discovery.
Abstract: The inspection of underneath vehicle system has been
given significant attention by governments after the threat of
terrorism become more prevalent. New technologies such as mobile
robots and computer vision are led to have more secure environment.
This paper proposed that a mobile robot like Aria robot can be used
to search and inspect the bombs under parking a lot vehicle. This
robot is using fuzzy logic and subsumption algorithms to control the
robot that movies underneath the vehicle. An OpenCV library and
laser Hokuyo are added to Aria robot to complete the experiment for
under vehicle inspection. This experiment was conducted at the
indoor environment to demonstrate the efficiency of our methods to
search objects and control the robot movements under vehicle. We
got excellent results not only by controlling the robot movement but
also inspecting object by the robot camera at same time. This success
allowed us to know the requirement to construct a new cost effective
robot with more functionality.
Abstract: Ontologies offer a means for representing and sharing
information in many domains, particularly in complex domains. For
example, it can be used for representing and sharing information
of System Requirement Specification (SRS) of complex systems
like the SRS of ERTMS/ETCS written in natural language. Since
this system is a real-time and critical system, generic ontologies,
such as OWL and generic ERTMS ontologies provide minimal
support for modeling temporal information omnipresent in these SRS
documents. To support the modeling of temporal information, one
of the challenges is to enable representation of dynamic features
evolving in time within a generic ontology with a minimal redesign
of it. The separation of temporal information from other information
can help to predict system runtime operation and to properly design
and implement them. In addition, it is helpful to provide a reasoning
and querying techniques to reason and query temporal information
represented in the ontology in order to detect potential temporal
inconsistencies. To address this challenge, we propose a lightweight
3-layer temporal Quality of Service (QoS) ontology for representing,
reasoning and querying over temporal and non-temporal information
in a complex domain ontology. Representing QoS entities in separated
layers can clarify the distinction between the non QoS entities
and the QoS entities in an ontology. The upper generic layer of
the proposed ontology provides an intuitive knowledge of domain
components, specially ERTMS/ETCS components. The separation of
the intermediate QoS layer from the lower QoS layer allows us to
focus on specific QoS Characteristics, such as temporal or integrity
characteristics. In this paper, we focus on temporal information that
can be used to predict system runtime operation. To evaluate our
approach, an example of the proposed domain ontology for handover
operation, as well as a reasoning rule over temporal relations in this
domain-specific ontology, are presented.
Abstract: In wireless communication, space-time block code (STBC), cyclic delay diversity (CDD) and space-time cyclic delay diversity (STCDD)are used as the spatial diversity schemes and have been widely studied for the reliablecommunication. If these schemes are used, the communication system can obtain the improved performance. However,the quality of the system is degraded when the distance between a source and a destination is distant in wireless communication system. In this paper, the cooperative transmission scheme using two sources is proposed and improves the performance of the wireless communication system.
Abstract: Brown seaweeds are abundant in Portuguese coastline
and represent an almost unexploited marine economic resource. One
of the most common species, easily available for harvesting in the
northwest coast, is Saccorhiza polyschides grows in the lowest shore
and costal rocky reefs. It is almost exclusively used by local farmers
as natural fertilizer, but contains a substantial amount of valuable
compounds, particularly alginates, natural biopolymers of high
interest for many industrial applications.
Alginates are natural polysaccharides present in cell walls of
brown seaweed, highly biocompatible, with particular properties that
make them of high interest for the food, biotechnology, cosmetics
and pharmaceutical industries. Conventional extraction processes are
based on thermal treatment. They are lengthy and consume high
amounts of energy and solvents. In recent years, microwave-assisted
extraction (MAE) has shown enormous potential to overcome major
drawbacks that outcome from conventional plant material extraction
(thermal and/or solvent based) techniques, being also successfully
applied to the extraction of agar, fucoidans and alginates. In the
present study, acid pretreatment of brown seaweed Saccorhiza
polyschides for subsequent microwave-assisted extraction (MAE) of
alginate was optimized. Seaweeds were collected in Northwest
Portuguese coastal waters of the Atlantic Ocean between May and
August, 2014. Experimental design was used to assess the effect of
temperature and acid pretreatment time in alginate extraction.
Response surface methodology allowed the determination of the
optimum MAE conditions: 40 mL of HCl 0.1 M per g of dried
seaweed with constant stirring at 20ºC during 14h. Optimal acid
pretreatment conditions have enhanced significantly MAE of
alginates from Saccorhiza polyschides, thus contributing for the
development of a viable, more environmental friendly alternative to
conventional processes.
Abstract: The objective of meta-analysis is to combine results
from several independent studies in order to create generalization
and provide evidence base for decision making. But recent studies
show that the magnitude of effect size estimates reported in many
areas of research significantly changed over time and this can
impair the results and conclusions of meta-analysis. A number of
sequential methods have been proposed for monitoring the effect
size estimates in meta-analysis. However they are based on statistical
theory applicable only to fixed effect model (FEM) of meta-analysis.
For random-effects model (REM), the analysis incorporates the
heterogeneity variance, τ 2 and its estimation create complications.
In this paper we study the use of a truncated CUSUM-type test with
asymptotically valid critical values for sequential monitoring in REM.
Simulation results show that the test does not control the Type I error
well, and is not recommended. Further work required to derive an
appropriate test in this important area of applications.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.
Abstract: Map is a powerful and convenient tool in helping us to
navigate to different places, but the use of indirect devices often
makes its usage cumbersome. This study intends to propose a new
map navigation dialogue that uses hand gesture. A set of dialogue
was developed from users’ perspective to provide users complete
freedom for panning, zooming, rotate, tilt and find direction
operations. A participatory design experiment was involved here
where one hand gesture and two hand gesture dialogues had been
analysed in the forms of hand gestures to develop a set of usable
dialogues. The major finding was that users prefer one-hand gesture
compared to two-hand gesture in map navigation.
Abstract: Nanocrystalline powders of the lead-free piezoelectric
material, tantalum-substituted potassium sodium niobate
(K0.5Na0.5)(Nb0.9Ta0.1)O3 (KNNT), were produced using a Retsch
PM100 planetary ball mill by setting the milling time to 15h, 20h,
25h, 30h, 35h and 40h, at a fixed speed of 250rpm. The average
particle size of the milled powders was found to decrease from 12nm
to 3nm as the milling time increases from 15h to 25h, which is in
agreement with the existing theoretical model. An anomalous
increase to 98nm and then a drop to 3nm in the particle size were
observed as the milling time further increases to 30h and 40h
respectively. Various sizes of these starting KNNT powders were
used to investigate the effect of milling time on the microstructure,
dielectric properties, phase transitions and piezoelectric properties of
the resulting KNNT ceramics. The particle size of starting KNNT
was somewhat proportional to the grain size. As the milling time
increases from 15h to 25h, the resulting ceramics exhibit
enhancement in the values of relative density from 94.8% to 95.8%,
room temperature dielectric constant (εRT) from 878 to 1213, and
piezoelectric charge coefficient (d33) from 108pC/N to 128pC/N. For
this range of ceramic samples, grain size refinement suppresses the
maximum dielectric constant (εmax), shifts the Curie temperature (Tc)
to a lower temperature and the orthorhombic-tetragonal phase
transition (Tot) to a higher temperature. Further increase of milling
time from 25h to 40h produces a gradual degradation in the values of
relative density, εRT, and d33 of the resulting ceramics.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.
Abstract: Recommendation systems are widely used in
e-commerce applications. The engine of a current recommendation
system recommends items to a particular user based on user
preferences and previous high ratings. Various recommendation
schemes such as collaborative filtering and content-based approaches
are used to build a recommendation system. Most of current
recommendation systems were developed to fit a certain domain such
as books, articles, and movies. We propose1 a hybrid framework
recommendation system to be applied on two dimensional spaces
(User × Item) with a large number of Users and a small number
of Items. Moreover, our proposed framework makes use of both
favorite and non-favorite items of a particular user. The proposed
framework is built upon the integration of association rules mining
and the content-based approach. The results of experiments show
that our proposed framework can provide accurate recommendations
to users.
Abstract: Creating a database scheme is essentially a manual
process. From a requirement specification the information contained
within has to be analyzed and reduced into a set of tables, attributes
and relationships. This is a time consuming process that has to go
through several stages before an acceptable database schema is
achieved. The purpose of this paper is to implement a Natural
Language Processing (NLP) based tool to produce a relational
database from a requirement specification. The Stanford CoreNLP
version 3.3.1 and the Java programming were used to implement the
proposed model. The outcome of this study indicates that a first draft
of a relational database schema can be extracted from a requirement
specification by using NLP tools and techniques with minimum user
intervention. Therefore this method is a step forward in finding a
solution that requires little or no user intervention.
Abstract: Floods play a key role in landform evolution of an
area. This process is likely to alter the topography of the earth’s
surface. The present study area, Kota Bharu is very prone to floods
extends from upstream of Kelantan River near Kemubu to the
downstream area near Kuala Besar. These flood events which occur
every year in the study area exhibit a strong bearing on river
morphological set-up. In the present study, three satellite imageries of
different time periods have been used to manifest the post-flood
landform changes. The pre-processing of the images such as subset,
geometric corrections and atmospheric corrections were carried-out
using ENVI 4.5 followed by the analysis processes. Twenty sets of
cross sections were plotted using software Erdas 9.2, ERDAS and
ArcGis 10 for the all three images. The results show a significant
change in the length of the cross section which suggest that the
geomorphological processes play a key role in carving and shaping
the river banks during the floods.
Abstract: Animal fats (camel, sheep, goat, rabbit and chicken)
and vegetable oils (corn, sunflower, palm oil and olive oil) were
substituted with different proportions (1, 5, 10 and 20%) of lard.
Fatty acid composition in TG and 2-MG were determined using
lipase hydrolysis and gas chromatography before and after
adulteration. Results indicated that, genuine lard had a high
proportion (60.97%) of the total palmitic acid at 2-MG. However, it
was 8.70%, 16.40%, 11.38%, 10.57%, 29.97 and 8.97% for camel,
beef, sheep, goat, rabbit and chicken, respectively. It could be noticed
also the position-2-MG is mostly occupied by unsaturated fatty acids
among all tested fats except lard. Vegetable oils (corn, sunflower,
palm oil and olive oil) revealed that the levels of palmitic acid
esterifies at 2-MG position was 6.84, 1.43, 9.86 and 1.70%,
respectively. It could be observed also the studied oils had a higher
level of unsaturated fatty acids in the same position, compared with
animal fats under investigation. Moreover, palmitic acid esterifies at
2-MG and PAEF increased gradually as the substituted levels
increased among all tested fat and oil samples. Statistical analysis
showed that the PAEF correlated well with lard level. The detection
of lard in some commercial processed foods (5 French fries, 4 Butter
fats, 5 processed meat and 6 candy samples) was carried out. Results
revealed that 2 samples of French fries and 4 samples of processed
meat contained lard due to their higher PAEF, while butter fat and
candy were free of lard.
Abstract: Today’s modern interconnected power system is
highly complex in nature. In this, one of the most important
requirements during the operation of the electric power system is the
reliability and security. Power and frequency oscillation damping
mechanism improve the reliability. Because of power system
stabilizer (PSS) low speed response against of major fault such as
three phase short circuit, FACTs devise that can control the network
condition in very fast time, are becoming popular. But FACTs
capability can be seen in a major fault present when nonlinear models
of FACTs devise and power system equipment are applied. To realize
this aim, the model of multi-machine power system with FACTs
controller is developed in MATLAB/SIMULINK using Sim Power
System (SPS) blockiest. Among the FACTs device, Static
synchronous series compensator (SSSC) due to high speed changes
its reactance characteristic inductive to capacitive, is effective power
flow controller. Tuning process of controller parameter can be
performed using different method. But Genetic Algorithm (GA)
ability tends to use it in controller parameter tuning process. In this
paper firstly POD controller is used to power oscillation damping.
But in this station, frequency oscillation dos not has proper damping
situation. So FOD controller that is tuned using GA is using that
cause to damp out frequency oscillation properly and power
oscillation damping has suitable situation.
Abstract: This paper proposes a new technique to design a
fixed-structure robust loop shaping controller for the pneumatic
servosystem. In this paper, a new method based on a particle swarm
optimization (PSO) algorithm for tuning the weighting function
parameters to design an H∞ controller is presented. The PSO
algorithm is used to minimize the infinity norm of the transfer
function of the nominal closed loop system to obtain the optimal
parameters of the weighting functions. The optimal stability margin is
used as an objective in PSO for selecting the optimal weighting
parameters; it is shown that the proposed method can simplify the
design procedure of H∞ control to obtain optimal robust controller for
pneumatic servosystem. In addition, the order of the proposed
controller is much lower than that of the conventional robust loop
shaping controller, making it easy to implement in practical works.
Also two-degree-of-freedom (2DOF) control design procedure is
proposed to improve tracking performance in the face of noise and
disturbance. Result of simulations demonstrates the advantages of the
proposed controller in terms of simple structure and robustness
against plant perturbations and disturbances.