Abstract: Doubly fed induction machines DFIM are used
mainly for wind energy conversion in MW power plants. This paper
presents a new strategy of field oriented control ,it is based on the
principle of a double flux orientation of stator and rotor at the same
time. Therefore, the orthogonality created between the two oriented
fluxes, which must be strictly observed, leads to generate a linear and
decoupled control with an optimal torque. The obtained simulation
results show the feasibility and the effectiveness of the suggested
method.
Abstract: This paper discusses a systematic design of a Σ-Δ fractional-N Phase-Locked Loop based on HDL behavioral modeling. The proposed design consists in describing the mixed behavior of this PLL architecture starting from the specifications of each building block. The HDL models of critical PLL blocks have been described in VHDL-AMS to predict the different specifications of the PLL. The effect of different noise sources has been efficiently introduced to study the PLL system performances. The obtained results are compared with transistor-level simulations to validate the effectiveness of the proposed models for wireless applications in the frequency range around 2.45 GHz.
Abstract: Article 5(3) of the Brussels I Regulation provides that a person domiciled in a Member State may be sued in another Member State in matters relating to tort, delict or quasi-delict, in the courts for the place where the harmful events occurred or may occur. For a number of years Article 5 (3) of the Brussels I Regulation has been at the centre of the debate regarding the intellectual property rights infringement over the Internet. Nothing has been done to adapt the provisions relating to non-internet cases of infringement of intellectual property rights to the context of the Internet. The author’s findings indicate that in the case of intellectual property rights infringement on the Internet, the plaintiff has the option to sue either: the court of the Member State of the event giving rise to the damage: where the publisher of the newspaper is established; the court of the Member State where the damage occurred: where defamatory article is distributed. However, it must be admitted that whilst infringement over the Internet has some similarity to multi-State defamation by means of newspapers, the position is not entirely analogous due to the cross-border nature of the Internet. A simple example which may appropriately illustrate its contentious nature is a defamatory statement published on a website accessible in different Member States, and available in different languages. Therefore, we need to answer the question: how these traditional jurisdictional rules apply in the case of intellectual property rights infringement over the Internet? Should these traditional jurisdictional rules be modified?
Abstract: In this paper, a second order autoregressive (AR)
model is proposed to discriminate alcoholics using single trial
gamma band Visual Evoked Potential (VEP) signals using 3 different
classifiers: Simplified Fuzzy ARTMAP (SFA) neural network (NN),
Multilayer-perceptron-backpropagation (MLP-BP) NN and Linear
Discriminant (LD). Electroencephalogram (EEG) signals were
recorded from alcoholic and control subjects during the presentation
of visuals from Snodgrass and Vanderwart picture set. Single trial
VEP signals were extracted from EEG signals using Elliptic filtering
in the gamma band spectral range. A second order AR model was
used as gamma band VEP exhibits pseudo-periodic behaviour and
second order AR is optimal to represent this behaviour. This
circumvents the requirement of having to use some criteria to choose
the correct order. The averaged discrimination errors of 2.6%, 2.8%
and 11.9% were given by LD, MLP-BP and SFA classifiers. The
high LD discrimination results show the validity of the proposed
method to discriminate between alcoholic subjects.
Abstract: In recent years, global warming has become a
worldwide problem. The reduction of carbon dioxide emissions is a
top priority for many companies in the manufacturing industry. In the
automobile industry as well, the reduction of carbon dioxide emissions
is one of the most important issues. Technology to reduce the weight
of automotive parts improves the fuel economy of automobiles, and is
an important technology for reducing carbon dioxide. Also, even if
this weight reduction technology is applied to electric automobiles
rather than gasoline automobiles, reducing energy consumption
remains an important issue. Plastic processing of hollow pipes is one
important technology for realizing the weight reduction of automotive
parts. Ohashi et al. [1],[2] present an example of research on pipe
formation in which a process was carried out to enlarge a pipe
diameter using a lost core, achieving the suppression of wall thickness
reduction and greater pipe expansion than hydroforming.
In this study, we investigated a method to increase the wall
thickness of a pipe through pipe compression using planetary rolls.
The establishment of a technology whereby the wall thickness of a
pipe can be controlled without buckling the pipe is an important
technology for the weight reduction of products. Using the finite
element analysis method, we predicted that it would be possible to
increase the compression of an aluminum pipe with a 3mm wall
thickness by approximately 20%, and wall thickness by approximately
20% by pressing the hollow pipe with planetary rolls.
Abstract: Nowadays there is a growing environmental concern
and the business communities have slowly started recognising
environmental protection and sustainable utilization of natural
resources into their marketing strategies. This paper discusses the
various Ecolabeling and Certification Systems developed world
over to regulate and introduce Fair Trade in Ornamental Fish
Industry. Ecolabeling and green certification are considered as part
of these strategies implemented partly out of compulsion from the
National and International Regulatory Bodies and Environmental
Movements. All the major markets of ornamental fishes like
European Union, USA and Japan have started putting restrictions on
the trade to impose ecolabeling as a non tariff barrier like the one
imposed on seafood and aqua cultured products. A review was done
on the available Ecolabeling and Green Certification Schemes
available at local, national and international levels for fisheries
including aquaculture and ornamental fish trade and to examine the
success and constraints faced by these schemes during its
implementation. The primary downside of certification is the
multiplicity of ecolabels and cost incurred by applicants for
certification, costs which may in turn be passed on to consumers.
The studies reveal serious inadequacies in a number of ecolabels
and cast doubt on their overall contribution to effective fisheries
management and sustainability. The paper also discusses the
inititive taken in India to develop guidelines for Green Certification
of Fresh water ornamental fishes.
Abstract: A cross-sectional study was carried out to determine the prevalence, species characterization and associated risk factors with Eimeria (E.) in sheep of district Toba Tek Singh from April, 2009 to March, 2010. Of the total 486 faecal samples examined for Eimeria, 209 (43%) were found infected with five species of Eimeria. Amongst the identified species of Eimeria, E. ovinoidalis was the commonest one (48.32%), followed in order by E. ahsata, E. intricata, E. parva and E. faurei with prevalence of 45.45, 28.71, 24.40 and 19.14 percent respectively. Peak prevalence was observed in August. Wet season (rainy and post-rainy) was found to be favourable for Eimeria infection. Lambs had significantly higher prevalence (P < 0.05) of Eimeria than adults. Similarly higher prevalence of Eimeria was observed in female as compared to male. Among management and husbandry practices; watering system, housing system, floor type and herd size strongly influenced the prevalence of Eimeria. Coccidiosis was more prevalent in closed housing system, non-cemented floor type, pond watered animals and larger herds (P < 0.05) as compared to open housing system, partially cemented floor type, tap watered animals and smaller herds respectively. Feeding system, breed and body condition of animals were not found as risk factors (P>0.05) influencing prevalence of Eimeria.
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: Malaria is a serious, acute and chronic relapsing
infection to humans. It is characterized by periodic attacks of chills,
fever, nausea, vomiting, back pain, increased sweating anemia,
splenomegaly (enlargement of the spleen) and often-fatal
complications.The malaria disease is caused by the multiplication of
protozoa parasite of the genus Plasmodium. Malaria in humans is due
to 4 types of malaria parasites such that Plasmodium falciparum,
Plasmodium vivax, Plasmodium malariae and Plasmodium ovale.
P.vivax malaria differs from P. falciparum malaria in that a person
suffering from P. vivax malaria can experience relapses of the
disease. Between the relapses, the malaria parasite will remain
dormant in the liver of the patient, leading to the patient being
classified as being in the dormant class. A mathematical model for
the transmission of P. vivax is developed in which the human
population is divided into four classes, the susceptible, the infected,
the dormant and the recovered. In this paper, we formulate the
dynamical model of P. vivax malaria to see the distribution of this
disease at the district level.
Abstract: New Zealand-s product markets experienced a surge in
import competition beginning from the late 1970-s when its
government began to promote a policy of more open markets. This
study considers how the trade liberalization aspect of the policy may
have influenced unionization and union-organizing success. For
describing the trade liberalization, a model shows how the removal of
import tariffs can lead to countervailing influences upon the union
membership of a domestic firm. The evidence supports the prediction
that union membership has been decreased rather than increased. In
the context of debates concerning globalization, it can be said that the
power of unions has been diminished.
Abstract: Middle-gate is located in Hasankeyf, Batman dating
back to 1800 BC and is one of the important historical structures in
Turkey. The ancient structure has suffered major structural cracks
due to aging as well as lateral pressure of a cracked rock which is
predicted to be about 100 tons. The existing support system was
found to be inadequate to support the load especially after a recent
rock fall in the close vicinity. Concerns were increased since the
existing support system that is integral with a damaged and cracked
gate wall needed to be replaced by a new support system. The
replacement process must be carefully monitored by crackmeters and
control mechanisms should be integrated to prevent cracks to expand
while the same crack width needs to be maintained after the
operation. The control system and actions taken during the
intervention are explained in this paper.
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: Protein subchloroplast locations are correlated with its
functions. In contrast to the large amount of available protein
sequences, the information of their locations and functions is less
known. The experiment works for identification of protein locations
and functions are costly and time consuming. The accurate prediction
of protein subchloroplast locations can accelerate the study of
functions of proteins in chloroplast. This study proposes a Random
Forest based method, ChloroRF, to predict protein subchloroplast
locations using interpretable physicochemical properties. In addition
to high prediction accuracy, the ChloroRF is able to select important
physicochemical properties. The important physicochemical
properties are also analyzed to provide insights into the underlying
mechanism.
Abstract: This paper is concerned with exponential stability and stabilization of switched linear systems with interval time-varying delays. The time delay is any continuous function belonging to a given interval, in which the lower bound of delay is not restricted to zero. By constructing a suitable augmented Lyapunov-Krasovskii functional combined with Leibniz-Newton-s formula, a switching rule for the exponential stability and stabilization of switched linear systems with interval time-varying delays and new delay-dependent sufficient conditions for the exponential stability and stabilization of the systems are first established in terms of LMIs. Numerical examples are included to illustrate the effectiveness of the results.
Abstract: This paper addresses the problem of how one can
improve the performance of a non-optimal filter. First the theoretical question on dynamical representation for a given time correlated
random process is studied. It will be demonstrated that for a wide class of random processes, having a canonical form, there exists
a dynamical system equivalent in the sense that its output has the
same covariance function. It is shown that the dynamical approach is more effective for simulating and estimating a Markov and non-
Markovian random processes, computationally is less demanding,
especially with increasing of the dimension of simulated processes.
Numerical examples and estimation problems in low dimensional
systems are given to illustrate the advantages of the approach. A very useful application of the proposed approach is shown for the
problem of state estimation in very high dimensional systems. Here a modified filter for data assimilation in an oceanic numerical model
is presented which is proved to be very efficient due to introducing
a simple Markovian structure for the output prediction error process
and adaptive tuning some parameters of the Markov equation.
Abstract: In this work, propagation of uncertainty during calibration
process of TRANUS, an integrated land use and transport model
(ILUTM), has been investigated. It has also been examined, through a
sensitivity analysis, which input parameters affect the variation of the
outputs the most. Moreover, a probabilistic verification methodology
of calibration process, which equates the observed and calculated
production, has been proposed. The model chosen as an application is
the model of the city of Grenoble, France. For sensitivity analysis and
uncertainty propagation, Monte Carlo method was employed, and a
statistical hypothesis test was used for verification. The parameters of
the induced demand function in TRANUS, were assumed as uncertain
in the present case. It was found that, if during calibration, TRANUS
converges, then with a high probability the calibration process is
verified. Moreover, a weak correlation was found between the inputs
and the outputs of the calibration process. The total effect of the
inputs on outputs was investigated, and the output variation was found
to be dictated by only a few input parameters.
Abstract: Surveillance system is widely used in the traffic
monitoring. The deployment of cameras is moving toward a
ubiquitous camera (UbiCam) environment. In our previous study, a
novel service, called GPS-VT, was firstly proposed by incorporating
global positioning system (GPS) and visual tracking techniques for
the UbiCam environment. The first prototype is called GODTA
(GPS-based Moving Object Detection and Tracking Approach). For a
moving person carried GPS-enabled mobile device, he can be
tracking when he enters the field-of-view (FOV) of a camera
according to his real-time GPS coordinate. In this paper, GPS-VT
service is applied to the tracking of vehicles. The moving speed of a
vehicle is much faster than a person. It means that the time passing
through the FOV is much shorter than that of a person. Besides, the
update interval of GPS coordinate is once per second, it is
asynchronous with the frame rate of the real-time image. The above
asynchronous is worsen by the network transmission delay. These
factors are the main challenging to fulfill GPS-VT service on a
vehicle.In order to overcome the influence of the above factors, a
back-propagation neural network (BPNN) is used to predict the
possible lane before the vehicle enters the FOV of a camera. Then, a
template matching technique is used for the visual tracking of a target
vehicle. The experimental result shows that the target vehicle can be
located and tracking successfully. The success location rate of the
implemented prototype is higher than that of the previous GODTA.
Abstract: The groundwater is one of the main sources for
sustainability in the United Arab Emirates (UAE). Intensive
developments in Al-Ain area lead to increase water demand, which
consequently reduced the overall groundwater quantity in major
aquifers. However, in certain residential areas within Al-Ain, it has
been noticed that the groundwater level is rising, for example in
Sha-ab Al Askher area. The reasons for the groundwater rising
phenomenon are yet to be investigated. In this work, twenty four
seismic refraction profiles have been carried out along the study
pilot area; as well as field measurement of the groundwater level in
a number of available water wells in the area. The processed
seismic data indicated the deepest and shallowest groundwater
levels are 15m and 2.3 meters respectively. This result is greatly
consistent with the proper field measurement of the groundwater
level. The minimum detected value may be referred to perched
subsurface water which may be associated to the infiltration from
the surrounding water bodies such as lakes, and elevated farms. The
maximum values indicate the accurate groundwater level within the
study area. The findings of this work may be considered as a
preliminary help to the decision makers.
Abstract: As a security mechanism, authorization is to provide access control to the system resources according to the polices and rules specified by the security strategies. Either by update or in the initial specification, conflicts in authorization is an issue needs to be solved. In this paper, we propose a new approach to solve conflict by using prioritized logic programs and discuss the uniqueness of its answer set. Addressing conflict resolution from logic programming viewpoint and the uniqueness analysis of the answer set provide a novel, efficient approach for authorization conflict resolution.
Abstract: Metal matrix composites have been increasingly used
as materials for components in automotive and aerospace industries
because of their improved properties compared with non-reinforced
alloys. During machining the selection of appropriate machining
parameters to produce job for desired surface roughness is of great
concern considering the economy of manufacturing process. In this
study, a surface roughness prediction model using fuzzy logic is
developed for end milling of Al-SiCp metal matrix composite
component using carbide end mill cutter. The surface roughness is
modeled as a function of spindle speed (N), feed rate (f), depth of cut
(d) and the SiCp percentage (S). The predicted values surface
roughness is compared with experimental result. The model predicts
average percentage error as 4.56% and mean square error as 0.0729.
It is observed that surface roughness is most influenced by feed rate,
spindle speed and SiC percentage. Depth of cut has least influence.