Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: In the present paper the results of a numerical study are presented, numerical models were developed to simulate the behaviour of vertical massive dikes. The proposed models were developed according to the geometry, boundary conditions, loading conditions and initial conditions of a physical model taken as reference. The results obtained were compared to the experimental data. As far as the overall behaviour, the displacements and the failure mechanisms of the dikes is concerned, the numerical results were in good agreement with the experimental results, which clearly indicates a good quality of numerical modelling. The validated numerical models were used in a parametric study were the displacements and failure mechanisms were fully investigated. Out of the results obtained, some conclusions and recommendations related to the design of massive dikes are proposed.
Abstract: The group invariant solution for Prandtl-s boundary layer equations for an incompressible fluid governing the flow in radial free, wall and liquid jets having finite fluid velocity at the orifice are investigated. For each jet a symmetry is associated with the conserved vector that was used to derive the conserved quantity for the jet elsewhere. This symmetry is then used to construct the group invariant solution for the third-order partial differential equation for the stream function. The general form of the group invariant solution for radial jet flows is derived. The general form of group invariant solution and the general form of the similarity solution which was obtained elsewhere are the same.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms is formulated and investigated. By employing the delay differential inequality and inequality technique developed by Xu et al., some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms are obtained. In particular, the estimate of the exponential convergence rate is also provided, which depends on system parameters, diffusion effect and impulsive disturbed intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.
Abstract: Implementation of response surface methodology (RSM) was employed to study the effects of two factor (rubber clearance and round per minute) in brown rice peeling machine of The optimal BROKENS yield (19.02, average of three repeats),.The optimized composition derived from RSM regression was analyzed using Regression analysis and Analysis of Variance (ANOVA). At a significant level α = 0.05, the values of Regression coefficient, R 2 (adj)were 97.35 % and standard deviation were 1.09513. The independent variables are initial rubber clearance, and round per minute parameters namely. The investigating responses are final rubber clearance, and round per minute (RPM). The restriction of the optimization is the designated.
Abstract: This paper presents an exact pruning algorithm with
adaptive pruning interval for general dynamic neural networks
(GDNN). GDNNs are artificial neural networks with internal dynamics.
All layers have feedback connections with time delays to the
same and to all other layers. The structure of the plant is unknown, so
the identification process is started with a larger network architecture
than necessary. During parameter optimization with the Levenberg-
Marquardt (LM) algorithm irrelevant weights of the dynamic neural
network are deleted in order to find a model for the plant as
simple as possible. The weights to be pruned are found by direct
evaluation of the training data within a sliding time window. The
influence of pruning on the identification system depends on the
network architecture at pruning time and the selected weight to be
deleted. As the architecture of the model is changed drastically during
the identification and pruning process, it is suggested to adapt the
pruning interval online. Two system identification examples show
the architecture selection ability of the proposed pruning approach.
Abstract: Today, node-disjoint routing becomes inessential
technique in communication of packets among various nodes in
networks. Meanwhile AODV (Ad Hoc On-demand Multipath
Distance Vector) creates single-path route between a pair of source
and destination nodes. Some researches has done so far to make
multipath node-disjoint routing based on AODV protocol. But
however their overhead and end-to-end delay are relatively high,
while the detail of their code is not available too. This paper proposes
a new approach of multipath node-disjoint routing based on AODV
protocol. Then the algorithm of analytical model is presented. The
extensive results of this algorithm will be presented in the next paper.
Abstract: Biomechanical properties of infantile aorta in vitro in
cases of different standard anastomoses: end-to-end (ETE), extended
anastomosis end-to-end (EETE) and subclavian flap aortoplasty
(SFA) used for surgical correction of coarctation were analyzed to
detect the influence of the method on the biomechanics of infantile
aorta and possible changes in haemodinamics. 10 specimens of native
aorta, 3 specimens with ETE, 4 EEET and 3 SFA were investigated.
The experiments showed a non-linear relationship between stress and
strain in the infantile aorta, the modulus of elasticity of the aortic wall
increased with the increase of inner pressure. In the case of
anastomosis end-to-end the modulus was almost constant, relevant to
the modulus of elasticity of the aorta with the inner pressure 100-120
mmHg. The anastomoses EETE and SFA showed elastic properties
closer to native aorta, the stiffness of ETE did not change with the
changes in inner pressure.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: In this paper, Economic Order Quantity (EOQ) based model for non-instantaneous Weibull distribution deteriorating items with power demand pattern is presented. In this model, the holding cost per unit of the item per unit time is assumed to be an increasing linear function of time spent in storage. Here the retailer is allowed a trade-credit offer by the supplier to buy more items. Also in this model, shortages are allowed and partially backlogged. The backlogging rate is dependent on the waiting time for the next replenishment. This model aids in minimizing the total inventory cost by finding the optimal time interval and finding the optimal order quantity. The optimal solution of the model is illustrated with the help of numerical examples. Finally sensitivity analysis and graphical representations are given to demonstrate the model.
Abstract: Tea is a widely consumed beverage that contains many components. Caffeine belongs to this group of components called alkaloids contain nitrogen. In this study caffeine contents of three types of Turkish teas are determined by using extraction method. After condensation process, residue of caffeine and oil are obtained with evaporation. The oil which is in the residue is removed by hot water. Extraction process performed by using chloroform and the crude caffeine is obtained. From the results of experiments, caffeine contents are found in black tea, green tea and earl grey tea as 3.57±0.43%, 3.11±0.02%, 4.29±0.27%, respectively. Caffeine contents which are found in 1, 5 and 10 cups of tea are calculated. Furthermore, the daily intake of caffeine from black teas that affects human health is investigated.
Abstract: A parametric study of a mixed-compression
supersonic inlet is performed and reported. The effects of inlet Mach
Numbers, varying from 4 to 10, and angle of attack, varying from 0
to 10, are reported for a constant inlet dynamic pressure. The paper
looked at the variations of mass flow rates through the inlet, gain in
entropy through the inlet, and the angles of the external oblique
shocks. The mass flow rates were found to decrease monotonically
with Mach numbers and increase with angle of attacks. On the other
hand the entropy gain through the inlet increased with increasing
Mach number and angle of attack. The variation in static pressure
was found to be identical from the inlet throat to the exit for Mach
number values higher than 6.
Abstract: A strategy is implemented to find the improved configuration design of an existing aircraft structure by executing topology and shape optimizations. Structural analysis of the Initial Design Space is performed in ANSYS under the loads pertinent to operating and ground conditions. By using the FEA results and data, an initial optimized layout configuration is attained by exploiting nonparametric topology optimization in TOSCA software. Topological optimized surfaces are then smoothened and imported in ANSYS to develop the geometrical features. Nodes at the critical locations of resulting voids are selected for sketching rough profiles. Rough profiles are further refined and CAD feasible geometric features are generated. The modified model is then analyzed under the same loadings and constraints as defined for topology optimization. Shape at the peak stress concentration areas are further optimized by exploiting the shape optimization in TOSCA.shape module. The harmonized stressed model with the modified surfaces is then imported in CATIA to develop the final design.
Abstract: This paper proposes a new procedure for analyzing means-end chain data in marketing research. Most commonly the collected data is summarized in the Hierarchical Value Map (HVM) illustrating the main attribute-consequence-value linkages. This paper argues that traditionally constructed HVM may give an erroneous impression of the results of a means-end study. To justify the arguments, an alternative procedure to (1) determine the dominant attribute-consequence-value linkages and (2) construct HVM in a precise manner is presented. The current approach makes a contribution to means-end analysis, allowing marketers to address a set of marketing problems, such as advertising strategy.
Abstract: Scolothrips longicornis Priesner is one of the
important predators of tetranychid mites with a wide distribution
throughout Iran. Life table and population growth parameters of S.
longicornis feeding on two-spotted spider mite, Tetranychus
turkestani Ugarov & Nikolski were investigated under laboratory
condition (26±1ºC, 65±5% R.H. and 16L: 8D). To carry of these
experiments, S. longicornis collections reared on cowpea infested
with T. turkestani were prepared. The eggs with less than 24 hours
old were selected and reared. The emerged larvae feeding directly on
cowpea leaf discs which were infested with T. turkestani. Thirty
females of S. longicornis with 24 hours age were selected and
released on infested leaf discs. They replaced daily to a new leaf disc
and the laying eggs have counted. The experiment continued till the
last thrips had died. The result showed that the mean age mortality of
the adult female thrips were between 21-25 days which is nearly
equal life expectancy (ex) at the time of adult eclosion. Parameters
related to reproductive table including gross reproductive rate, net
reproductive rate, intrinsic rate of natural increase and finite rate of
increase were 48.91, 37.63, 0.26 and 2.3, respectively. Mean age per
female/day, mean fertile egg per female/day, gross hatch rate, mean
net age fertility, mean net age fecundity, net fertility rate and net
fecundity rate were 2.23, 1.76, 0.87, 13.87, 14.26, 69.1 and 78.5,
respectively. Sex ratio of offspring also recorded daily. The highest
sex ratio for females was 0.88 in first day of oviposition. The sex
ratio decreased gradually and reached under 0.46 after the day 26 and
the oviposition rate declined. Then it seems that maintenance of
rearing culture of predatory thrips for mass rearing later than 26 days
after egg-laying commence is not profitable.
Abstract: Research in distributed artificial intelligence and multiagent systems consider how a set of distributed entities can interact and coordinate their actions in order to solve a given problem. In this paper an overview of this concept and its evolution is presented particularly its application in the design of intelligent tutoring systems. An intelligent tutor based on the concept of agent and centered specifically on the design of a pedagogue agent is illustrated. Our work has two goals: the first one concerns the architecture aspect and the design of a tutor using multiagent approach. The second one deals particularly with the design of a part of a tutor system: the pedagogue agent.
Abstract: Land shortage for burials is one of many issues that emerge out of accelerated urban growth in most developing Asian cities, including Kuala Lumpur. Despite actions taken by the federal government and local authorities in addressing this issue, there is no strategic solution being formulated. Apart from making provisions for land to be developed as new cemeteries, the future plan is merely to allocate reserve land to accommodate the increasing demands of burial grounds around the city. This paper examines problems that arise from the traditional practices of Malay funerary as well as an insight to current urban practices in managing Muslim burial spaces around Kuala Lumpur metropolitan region. This paper will also provide some solutions through design approach that can be applied to counter the existing issues.
Abstract: In this paper, a novel adaptive fuzzy sliding mode
control method is proposed for the robust tracking control of robotic
manipulators. The proposed controller possesses the advantages of
adaptive control, fuzzy control, and sliding mode control. First, system
stability and robustness are guaranteed based on the sliding mode
control. Further, fuzzy rules are developed incorporating with
adaptation law to alleviate the input chattering effectively. Stability of
the control system is proven by using the Lyapunov method. An
application to a three-degree-of-freedom robotic manipulator is
carried out. Accurate trajectory tracking as well as robustness is
achieved. Input chattering is greatly eliminated.