Abstract: A feasibility study for the design and construction of a
pilot plant for the extraction of castor oil in South Africa was
conducted. The study emphasized the four critical aspects of project
feasibility analysis, namely technical, financial, market and
managerial aspects. The technical aspect involved research on
existing oil extraction technologies, namely: mechanical pressing and
solvent extraction, as well as assessment of the proposed production
site for both short and long term viability of the project. The site is
on the outskirts of Nkomazi village in the Mpumalanga province,
where connections for water and electricity are currently underway,
potential raw material supply proves to be reliable since the province
is known for its commercial farming. The managerial aspect was
evaluated based on the fact that the current producer of castor oil will
be fully involved in the project while receiving training and technical
assistance from Sasol Technology, the TSC and SEDA. Market and
financial aspects were evaluated and the project was considered
financially viable with a Net Present Value (NPV) of R2 731 687 and
an Internal Rate of Return (IRR) of 18% at an annual interest rate of
10.5%. The payback time is 6years for analysis over the first 10
years with a net income of R1 971 000 in the first year. The project
was thus found to be feasible with high chance of success while
contributing to socio-economic development. It was recommended
for lab tests to be conducted to establish process kinetics that would
be used in the initial design of the plant.
Abstract: Isobaric and cooling zone of iron ore reactor have been
simulated. In this paper, heat and mass transfer equation are
formulated to perform the temperature and concentration of gas and
solid phase respectively. Temperature profile for isobaric zone is
simulated on the range temperature of 873-1163K while cooling zone
is simulated on the range temperature of 733-1139K. The simulation
results have a good agreement with the plant data. Total carbon
formation in the isobaric zone is only 30% of total carbon contained in
the sponge iron product. The formation of Fe3C in isobaric zone
reduces metallization degree up to 0.58% whereas reduction of
metallization degree in cooling zone up to 1.139%. The decreasing of
sponge iron temperature in the isobaric and cooling zone is around 300
K and 600 K respectively.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: Data mining can be called as a technique to extract
information from data. It is the process of obtaining hidden
information and then turning it into qualified knowledge by statistical
and artificial intelligence technique. One of its application areas is
medical area to form decision support systems for diagnosis just by
inventing meaningful information from given medical data. In this
study a decision support system for diagnosis of illness that make use
of data mining and three different artificial intelligence classifier
algorithms namely Multilayer Perceptron, Naive Bayes Classifier and
J.48. Pima Indian dataset of UCI Machine Learning Repository was
used. This dataset includes urinary and blood test results of 768
patients. These test results consist of 8 different feature vectors.
Obtained classifying results were compared with the previous studies.
The suggestions for future studies were presented.
Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: The intrusion detection problem has been frequently studied, but intrusion detection methods are often based on a single point of view, which always limits the results. In this paper, we introduce a new intrusion detection model based on the combination of different current methods. First we use a notion of distance to unify the different methods. Second we combine these methods using the Pearson correlation coefficients, which measure the relationship between two methods, and we obtain a combined distance. If the combined distance is greater than a predetermined threshold, an intrusion is detected. We have implemented and tested the combination model with two different public data sets: the data set of masquerade detection collected by Schonlau & al., and the data set of program behaviors from the University of New Mexico. The results of the experiments prove that the combination model has better performances.
Abstract: In this paper, fully developed flow and heat transfer of
viscoelastic materials in curved ducts with square cross section under
constant heat flux have been investigated. Here, staggered mesh is
used as computational grids and flow and heat transfer parameters
have been allocated in this mesh with marker and cell method.
Numerical solution of governing equations has being performed with
FTCS finite difference method. Furthermore, Criminale-Eriksen-
Filbey (CEF) constitutive equation has being used as viscoelastic
model. CEF constitutive equation is a suitable model for studying
steady shear flow of viscoelastic materials which is able to model
both effects of the first and second normal stress differences. Here, it
is shown that the first and second normal stresses differences have
noticeable and inverse effect on secondary flows intensity and mean
Nusselt number which is the main novelty of current research.
Abstract: Modeling of the distributed systems allows us to
represent the whole its functionality. The working system instance
rarely fulfils the whole functionality represented by model; usually
some parts of this functionality should be accessible periodically.
The reporting system based on the Data Warehouse concept seams to
be an intuitive example of the system that some of its functionality is
required only from time to time. Analyzing an enterprise risk
associated with the periodical change of the system functionality, we
should consider not only the inaccessibility of the components
(object) but also their functions (methods), and the impact of such a
situation on the system functionality from the business point of view.
In the paper we suggest that the risk attributes should be estimated
from risk attributes specified at the requirements level (Use Case in
the UML model) on the base of the information about the structure of
the model (presented at other levels of the UML model). We argue
that it is desirable to consider the influence of periodical changes in
requirements on the enterprise risk estimation. Finally, the
proposition of such a solution basing on the UML system model is
presented.
Abstract: In the effort to reduce water consumption for resorts,
more water conservation practices need to be implemented. Hence
water audits need to be performed to obtain a baseline of water
consumption, before planning water conservation practices. In this
study, a water audit framework specifically for resorts was created,
and the audit was performed on two resorts: Resort A in Langkawi,
Malaysia; and Resort B in Miri, Malaysia. From the audit, the total
daily water consumption for Resorts A and B were estimated to be
180m3 and 330 m3 respectively, while the actual water consumption
(based on water meter readings) were 175 m3 and 325 m3. This
suggests that the audit framework is reasonably accurate and may be
used to account for most of the water consumption sources in a
resort. The daily water consumption per guest is about 500 litres. The
water consumption of both resorts is poorly rated compared with
established benchmarks. Water conservation measures were
suggested for both resorts.
Abstract: Flow through micro and mini channels requires relatively
high driving pressure due to the large fluid pressure drop
through these channels. Consequently the forces acting on the walls of
the channel due to the fluid pressure are also large. Due to these forces
there are displacement fields set up in the solid substrate containing
the channels. If the movement of the substrate is constrained at some
points, then stress fields are established in the substrate. On the other
hand, if the deformation of the channel shape is sufficiently large
then its effect on the fluid flow is important to be calculated. Such
coupled fluid-solid systems form a class of problems known as fluidstructure
interactions. In the present work a co-located finite volume
discretization procedure on unstructured meshes is described for
solving fluid-structure interaction type of problems. A linear elastic
solid is assumed for which the effect of the channel deformation
on the flow is neglected. Thus the governing equations for the
fluid and the solid are decoupled and are solved separately. The
procedure is validated by solving two benchmark problems, one from
fluid mechanics and another from solid mechanics. A fluid-structure
interaction problem of flow through a U-shaped channel embedded
in a plate is solved.
Abstract: Wireless sensor networks have been used in wide
areas of application and become an attractive area for researchers in
recent years. Because of the limited energy storage capability of
sensor nodes, Energy consumption is one of the most challenging
aspects of these networks and different strategies and protocols deals
with this area. This paper presents general methods for designing low
power wireless sensor network. Different sources of energy
consumptions in these networks are discussed here and techniques for
alleviating the consumption of energy are presented.
Abstract: A predictive clustering hybrid regression (pCHR)
approach was developed and evaluated using dataset from H2-
producing sucrose-based bioreactor operated for 15 months. The aim
was to model and predict the H2-production rate using information
available about envirome and metabolome of the bioprocess. Selforganizing
maps (SOM) and Sammon map were used to visualize the
dataset and to identify main metabolic patterns and clusters in
bioprocess data. Three metabolic clusters: acetate coupled with other
metabolites, butyrate only, and transition phases were detected. The
developed pCHR model combines principles of k-means clustering,
kNN classification and regression techniques. The model performed
well in modeling and predicting the H2-production rate with mean
square error values of 0.0014 and 0.0032, respectively.
Abstract: The cables in a nuclear power plant are designed to be
used for about 40 years in safe operation environment. However, the
heat and radiation in the nuclear power plant causes the rapid
performance deterioration of cables in nuclear vessels and heat
exchangers, which requires cable lifetime estimation. The most
accurate method of estimating the cable lifetime is to evaluate the
cables in a laboratory. However, removing cables while the plant is
operating is not allowed because of its safety and cost. In this paper, a
robot system to estimate the cable lifetime in nuclear power plants is
developed and tested. The developed robot system can calculate a
modulus value to estimate the cable lifetime even when the nuclear
power plant is in operation.
Abstract: Semisolid metal processing uses solid–liquid slurries
containing fine and globular solid particles uniformly distributed in a
liquid matrix, which can be handled as a solid and flow like a liquid.
In the recent years, many methods have been introduced for the
production of semisolid slurries since it is scientifically sound and
industrially viable with such preferred microstructures called
thixotropic microstructures as feedstock materials. One such process
that needs very low equipment investment and running costs is the
cooling slope. In this research by using a mechanical stirrer slurry
maker constructed by the authors, the effects of mechanical stirring
parameters such as: stirring time, stirring temperature and stirring
Speed on micro-structure and mechanical properties of A360
aluminum alloy in semi-solid forming, are investigated. It is
determined that mold temperature and holding time of part in
temperature of 580ºC have a great effect on micro-structure and
mechanical properties(stirring temperature of 585ºC, stirring time of
20 minutes and stirring speed of 425 RPM). By optimizing the
forming parameters, dendrite microstructure changes to globular and
mechanical properties improves. This is because of breaking and
globularzing dendrites of primary α-AL.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: Forecasting the values of the indicators, which
characterize the effectiveness of performance of organizations is of
great importance for their successful development. Such forecasting
is necessary in order to assess the current state and to foresee future
developments, so that measures to improve the organization-s
activity could be undertaken in time. The article presents an
overview of the applied mathematical and statistical methods for
developing forecasts. Special attention is paid to artificial neural
networks as a forecasting tool. Their strengths and weaknesses are
analyzed and a synopsis is made of the application of artificial neural
networks in the field of forecasting of the values of different
education efficiency indicators. A method of evaluation of the
activity of universities using the Balanced Scorecard is proposed and
Key Performance Indicators for assessment of e-learning are
selected. Resulting indicators for the evaluation of efficiency of the
activity are proposed. An artificial neural network is constructed and
applied in the forecasting of the values of indicators for e-learning
efficiency on the basis of the KPI values.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.