Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: This paper describes various stages of design and prototyping of a modular robot for use in various industrial applications. The major goal of current research has been to design and make different robotic joints at low cost capable of being assembled together in any given order for achieving various robot configurations. Five different types of joins were designed and manufactured where extensive research has been carried out on the design of each joint in order to achieve optimal strength, size, modularity, and price. This paper presents various stages of research and development undertaken to engineer these joints that include material selection, manufacturing, and strength analysis. The outcome of this research addresses the birth of a new generation of modular industrial robots with a wider range of applications and greater efficiency.
Abstract: In this paper, the finite-time stabilization of a class of multi-state time delay of fractional-order system is proposed. First, we define finite-time stability with the fractional-order system. Second, by using Generalized Gronwall's approach and the methods of the inequality, we get some conditions of finite-time stability for the fractional system with multi-state delay. Finally, a numerical example is given to illustrate the result.
Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: Machine-understandable data when strongly
interlinked constitutes the basis for the SemanticWeb. Annotating
web documents is one of the major techniques for creating metadata
on the Web. Annotating websitexs defines the containing data in a
form which is suitable for interpretation by machines. In this paper,
we present a better and improved approach than previous [1] to
annotate the texts of the websites depends on the knowledge base.
Abstract: The service sector continues to grow and the percentage
of GDP accounted for by service industries keeps increasing. The
growth and importance of service to an economy is not just a
phenomenon of advanced economies, service is now a majority of the
world gross domestic products. However, the performance evaluation
process of new service development problems generally involves
uncertain and imprecise data. This paper presents a 2-tuple fuzzy
linguistic computing approach to dealing with heterogeneous
information and information loss problems while the processes of
subjective evaluation integration. The proposed method based on group
decision-making scenario to assist business managers in measuring
performance of new service development manipulates the
heterogeneity integration processes and avoids the information loss
effectively.
Abstract: Time delay in bilateral teleoperation system was
introduced as a sufficient reason to make the system unstable or
certainly degrade the system performance. In this paper, simulations
and experimental results of implementing p-like control scheme,
under different ranges of variable time delay, will be presented to
verify a certain criteria, which guarantee the system stability and
position tracking. The system consists of two Phantom premium 1.5A
devices. One of them acts as a master and the other acts as a slave.
The study includes deriving the Phantom kinematic and dynamic
model, establishing the link between the two Phantoms over
Simulink in Matlab, and verifying the stability criteria with
simulations and real experiments.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: These This paper looks into frameworks which aim at
furthering the discussion of the role of regenerative design practices
in a city-s historic core and the tool of urban design to achieve urban
revitalization on the island of Cyprus. It also examines the region-s
demographic mix, the effectiveness of its governmental coordination
and the strategies of adaptive reuse and strategic investments in older
areas with existing infrastructure. The two main prongs of
investigation will consider the effect of the existing and proposed
changes in the physical infrastructure and fabric of the city, as well as
the catalytic effect of sustainable urban design practices. Through this
process, the work hopes to integrate the contained potential within
the existing historic core and the contributions and participation of
the migrant and immigrant populations to the local economy. It also
examines ways in which this coupling of factors can bring to the front
the positive effects of this combined effort on an otherwise sluggish
local redevelopment effort. The data for this study is being collected
and organized as part of ongoing urban design and development
student workshop efforts in urban planning and design education.
The work is presented in graphic form and includes data collected
from interviews with study area organizations and the community at
large. Planning work is also based on best practices initiated by the
staff of the Nicosia Master Plan task force, which coordinates holistic
planning efforts for the historic center of the city of Nicosia.
Abstract: As current business environment is demanding a
constant adaptation of companies, the planning and strategic
management should be an ongoing and natural process in all kind of
organizations. The use of management and monitoring strategic
performance tools such as the Balanced Scorecard (BSC) have been
popular; even to Small and Medium-sized Enterprises. This paper
aims to investigate whether the BSC is being used in monitoring the
performance of small businesses, particularly in small fuel retailers
companies, which are competing in co-branding; and if not, it aims to
identify its strategic orientation in order to recommend a possible
strategy map for those managers that are willing to adopt this model
as an alternative to traditional ones for organizational performance
evaluation, which often focus only on evaluation of the
organizational financial performance.
Abstract: In this paper we propose a method for vision systems
to consistently represent functional dependencies between different
visual routines along with relational short- and long-term knowledge
about the world. Here the visual routines are bound to visual properties
of objects stored in the memory of the system. Furthermore,
the functional dependencies between the visual routines are seen
as a graph also belonging to the object-s structure. This graph is
parsed in the course of acquiring a visual property of an object to
automatically resolve the dependencies of the bound visual routines.
Using this representation, the system is able to dynamically rearrange
the processing order while keeping its functionality. Additionally, the
system is able to estimate the overall computational costs of a certain
action. We will also show that the system can efficiently use that
structure to incorporate already acquired knowledge and thus reduce
the computational demand.
Abstract: The paper is concerned with developing stochastic delay mechanisms for efficient multicast protocols and for smooth mobile handover processes which are capable of preserving a given Quality of Service (QoS). In both applications the participating entities (receiver nodes or subscribers) sample a stochastic timer and generate load after a random delay. In this way, the load on the networking resources is evenly distributed which helps to maintain QoS communication. The optimal timer distributions have been sought in different p.d.f. families (e.g. exponential, power law and radial basis function) and the optimal parameter have been found in a recursive manner. Detailed simulations have demonstrated the improvement in performance both in the case of multicast and mobile handover applications.
Abstract: Breastfeeding is an important concept in the maternal life of a woman. In this paper, we focus on exclusive breastfeeding. Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. This type of breastfeeding is very important during the first six months because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in Mauritius, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we give an overview of exclusive breastfeeding in Mauritius and the factors influencing it. We further analyze the local practices of exclusive breastfeeding using the Generalized Poisson regression model and the negative-binomial model since the data are over-dispersed.
Abstract: The main purpose of this research was to analyze Socio-Cultural obstacles of disseminating of nanotechnology in Iran's agricultural section. One hundred twenty eight out of a total of 190 researchers with different levels of expertise in and familiarity with nanotechnology were randomly selected and questionnaires completed by them. Face validity have been done by expert's suggestion and correction, reliability by using Cronbakh-Alpha formula. The results of a factor analysis showed variation for different factors. For cultural factors 19/475 percent, for management 13/139 percent, information factor 11/277 percent, production factor 9/703 percent, social factor 9/267 percent, and for attitude factor it became 8/947 percent. Also results indicated that socio-cultural factors were the most important obstacle for nanotechnology dissemination in agricultural section in Iran.
Abstract: The original idea for a feature film may come from a
writer, director or a producer. Director is the person responsible for
the creative aspects, both interpretive and technical, of a motion
picture production in a film. Director may be shot discussing his
project with his or her cowriters, members of production staff, and
producer, and director may be shown selecting locales or
constructing sets. All these activities provide, of course, ways of
externalizing director-s ideas about the film. A director sometimes
pushes both the film image and techniques of narration to new artistic
limits, but main responsibility of director is take the spectator to an
original opinion in his philosophical approach. Director tries to find
an artistic angle in every scene and change screenplay into an
effective story and sets his film on a spiritual and philosophical base.