Abstract: The world demand for potable water is
increasing every day with growing population. Desalination
using solar energy is suitable for potable water production
from brackish and seawater. In this paper, we present a
theoretical study of solar distillation in a single basin under
the open environmental conditions of Chabahar-Iran. The still
has a base area of 2000mm×500mm with a glass cover
inclined at 25° in order to obtain extra solar energy. We model
the still and conduct its energy balance equations under minor
assumptions. We computed the temperatures of glass cover,
seawater interface, moist air and bottom using numerical
method. The investigation addressed the following: The still
productivity, distilled water salinity and still performance in
terms of the still efficiency. Calculated still productivity in
July was higher than December. So in this paper, we show
that still productivity is directly functioning of solar radiation.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: The financial crisis has decreased the opportunities of
small businesses to acquire financing through conventional financial
actors, such as commercial banks. This credit constraint is partly the
reason for the emergence of new alternatives of financing, in addition
to the spreading opportunities for communication and secure
financial transfer through Internet. One of the most interesting venues
for finance is termed “crowdfunding". As the term suggests
crowdfunding is an appeal to prospective customers and investors to
form a crowd that will finance projects that otherwise would find it
hard to generate support through the most common financial actors.
Crowdfunding is in this paper divided into different models; the
threshold model, the microfinance model, the micro loan model and
the equity model. All these models add to the financial possibilities of
emerging entrepreneurs.
Abstract: The paper presents the modeling of nonlinear
longitudinal aerodynamics using flight data of Hansa-3 aircraft at
high angles of attack near stall. The Kirchhoff-s quasi-steady stall
model has been used to incorporate nonlinear aerodynamic effects in
the aerodynamic model used to estimate the parameters, thereby,
making the aerodynamic model nonlinear. The Maximum Likelihood
method has been applied to the flight data (at high angles of attack)
for the estimation of parameters (aerodynamic and stall
characteristics) using the nonlinear aerodynamic model. To improve
the accuracy level of the estimates, an approach of fixing the strong
parameters has also been presented.
Abstract: In today-s turbulent environment, companies are faced with two principal challenges. On the one hand, it is necessary to produce ever more cost-effectively to remain competitive. On the other hand, factories need to be transformable in order to manage unpredictable changes in the corporate environment. To deal with these different challenges, companies use the philosophy of lean production in the first case, in the second case the philosophy of transformability. To a certain extent these two approaches follow different directions. This can cause conflicts when designing factories. Therefore, the Institute of Production Systems and Logistics (IFA) of the Leibniz University of Hanover has developed a procedure to allow companies to evaluate and design their factories with respect to the requirements of both philosophies.
Abstract: The paper considered the construction of BIBDs using potential Lotto Designs (LDs) earlier derived from qualifying parent BIBDs. The study utilized Li’s condition pr t−1 ( t−1 2 ) + pr− pr t−1 (t−1) 2 < ( p 2 ) λ, to determine the qualification of a parent BIBD (v, b, r, k, λ) as LD (n, k, p, t) constrained on v ≥ k, v ≥ p, t ≤ min{k, p} and then considered the case k = t since t is the smallest number of tickets that can guarantee a win in a lottery. The (15, 140, 28, 3, 4) and (7, 7, 3, 3, 1) BIBDs were selected as parent BIBDs to illustrate the procedure. These BIBDs yielded three potential LDs each. Each of the LDs was completely generated and their properties studied. The three LDs from the (15, 140, 28, 3, 4) produced (9, 84, 28, 3, 7), (10, 120, 36, 3, 8) and (11, 165, 45, 3, 9) BIBDs while those from the (7, 7, 3, 3, 1) produced the (5, 10, 6, 3, 3), (6, 20, 10, 3, 4) and (7, 35, 15, 3, 5) BIBDs. The produced BIBDs follow the generalization (v + 1, b + r + λ + 1, r +λ+1, k, λ+1) where (v, b, r, k, λ) are the parameters of the (9, 84, 28, 3, 7) and (5, 10, 6, 3, 3) BIBDs. All the BIBDs produced are unreduced designs.
Abstract: The emergence of mobile application services and App
Store has led to the explosive growth of user innovation, which users
voluntarily contribute to. User innovation communities where end
users freely reveal innovative ideas and needs with other community
members are becoming increasingly influential in this area. However,
user-s ideas in user innovation community are not enough to be new
service opportunity, because some of them can already developed as
existing services in App Store. Moreover, the existing services similar
to new service opportunity can be significant references to apply
analogy to develop service concept. In response, this research
proposes Case-Based Reasoning approach to matching the user needs
and existing services, identifying unmet opportunistic user needs, and
retrieving similar services with opportunity. Due to its intuitive and
transparent algorithm, users related to App Store innovation
communities can easily employ Case-Based Reasoning based
approach to their innovation.
Abstract: Background: This investigated the mental health of the elderly survivors six months, ten months and two years after the “5.12 Wenchuan" earthquake. Methods: Two hundred and thirty-two physically healthy older survivors from earthquake-affected Mianyang County were interviewed. The measures included the Revised Impact of Event Scale (IES-R, Chinese version, for PTSD) and a Chinese Mental Health Inventory for the Elderly (MHIE). A repeated measures ANOVA test was used for statistical analysis. Results: The follow-up group had a statistically significant lower IES-R score and lower MHIE score than the initial group ten months after the earthquake. Two years later, the score of IES-R in follow-up group were still lower than that of non-follow-up group, but no differences were significant on the score of MHIE between groups. Furthermore, a negative relationship was found between scores of IES-R and MHIE. Conclusion: The earthquake has had a persistent negative impact on older survivors- mental health within the two-year period and that although the PTSD level declined significantly with time, it did not disappear completely.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: By employing BS (Base Station) cooperation we can
increase substantially the spectral efficiency and capacity of cellular
systems. The signals received at each BS are sent to a central unit that
performs the separation of the different MT (Mobile Terminal) using
the same physical channel. However, we need accurate sampling and
quantization of those signals so as to reduce the backhaul
communication requirements.
In this paper we consider the optimization of the quantizers for BS
cooperation systems. Four different quantizer types are analyzed and
optimized to allow better SQNR (Signal-to-Quantization Noise
Ratio) and BER (Bit Error Rate) performance.
Abstract: The position and momentum space information entropies
of hydrogen atom are exactly evaluated. Using isospectral
Hamiltonian approach, a family of isospectral potentials is constructed having same energy eigenvalues as that of the original potential. The information entropy content is obtained in position
space as well as in momentum space. It is shown that the information
entropy content in each level can be re-arranged as a function of deformation parameter.
Abstract: Intellectual capital reporting becomes critical at
universities, mainly due to the fact that knowledge is the main output
as well as input in these institutions. In addition, universities have
continuous external demands for greater information and
transparency about the use of public funds, and are increasingly
provided with greater autonomy regarding their organization,
management, and budget allocation. This situation requires new
management and reporting systems. The purpose of the present study
is to provide a model for intellectual capital report in Spanish
universities. To this end, a questionnaire was sent to every member of
the Social Councils of Spanish public universities in order to identify
which intangible elements university stakeholders demand most. Our
proposal for an intellectual capital report aims to act as a guide to
help the Spanish universities on the road to the presentation of
information on intellectual capital which can assist stakeholders to
make the right decisions.
Abstract: An empirical study of web applications that use
software frameworks is presented here. The analysis is based on two
approaches. In the first, developers using such frameworks are
required, based on their experience, to assign weights to parameters
such as database connection. In the second approach, a performance
testing tool, OpenSTA, is used to compute start time and other such
measures. From such an analysis, it is concluded that open source
software is superior to proprietary software. The motivation behind
this research is to examine ways in which a quantitative assessment
can be made of software in general and frameworks in particular.
Concepts such as metrics and architectural styles are discussed along
with previously published research.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: The most important parameter in transformers life
expectancy is the hot-spot temperature level which accelerates the
rate of aging of the insulation. The aim of this paper is to present
thermal models for transformers loaded at prefabricated MV/LV
transformer substations and outdoor situations. The hot-spot
temperature of transformers is studied using their top-oil temperature
rise models. The thermal models proposed for hot-spot and top-oil
temperatures of different operating situations are compared. Since the
thermal transfer is different for indoor and outdoor transformers
considering their operating conditions, their hot-spot thermal models
differ from each other. The proposed thermal models are verified by
the results obtained from the experiments carried out on a typical
1600 kVA, 30 /0.4 kV, ONAN transformer for both indoor and
outdoor situations.
Abstract: Median filter is widely used to remove impulse noise
without blurring sharp edges. However, when noise level increased,
or with thin edges, median filter may work poorly. This paper
proposes a new filter, which will detect edges along four possible
directions, and then replace noise corrupted pixel with estimated
noise-free edge median value. Simulations show that the proposed
multi-stage directional median filter can provide excellent
performance of suppressing impulse noise in all situations.
Abstract: The Muslim faith requires individuals to fast between
the hours of sunrise and sunset during the month of Ramadan. Our
recent work has concentrated on some of the changes that take place
during the daytime when fasting. A questionnaire was developed to
assess subjective estimates of physical, mental and social activities,
and fatigue. Four days were studied: in the weeks before and after
Ramadan (control days) and during the first and last weeks of
Ramadan (experimental days). On each of these four days, this
questionnaire was given several times during the daytime and once
after the fast had been broken and just before individuals retired at
night.
During Ramadan, daytime mental, physical and social activities
all decreased below control values but then increased to abovecontrol
values in the evening. The desires to perform physical and
mental activities showed very similar patterns. That is, individuals
tried to conserve energy during the daytime in preparation for the
evenings when they ate and drank, often with friends. During
Ramadan also, individuals were more fatigued in the daytime and
napped more often than on control days. This extra fatigue probably
reflected decreased sleep, individuals often having risen earlier
(before sunrise, to prepare for fasting) and retired later (to enable
recovery from the fast).
Some physiological measures and objective measures of
performance (including the response to a bout of exercise) have also
been investigated. Urine osmolality fell during the daytime on
control days as subjects drank, but rose in Ramadan to reach values
at sunset indicative of dehydration. Exercise performance was also
compromised, particularly late in the afternoon when the fast had
lasted several hours. Self-chosen exercise work-rates fell and a set
amount of exercise felt more arduous. There were also changes in
heart rate and lactate accumulation in the blood, indicative of greater
cardiovascular and metabolic stress caused by the exercise in
subjects who had been fasting. Daytime fasting in Ramadan produces
widespread effects which probably reflect combined effects of sleep
loss and restrictions to intakes of water and food.
Abstract: In this paper, we study a class of serially concatenated block codes (SCBC) based on matrix interleavers, to be employed in fixed wireless communication systems. The performances of SCBC¬coded systems are investigated under various interleaver dimensions. Numerical results reveal that the matrix interleaver could be a competitive candidate over conventional block interleaver for frame lengths of 200 bits; hence, the SCBC coding based on matrix interleaver is a promising technique to be employed for speech transmission applications in many international standards such as pan-European Global System for Mobile communications (GSM), Digital Cellular Systems (DCS) 1800, and Joint Detection Code Division Multiple Access (JD-CDMA) mobile radio systems, where the speech frame contains around 200 bits.
Abstract: This paper proposed a novel model for short term load
forecast (STLF) in the electricity market. The prior electricity
demand data are treated as time series. The model is composed of
several neural networks whose data are processed using a wavelet
technique. The model is created in the form of a simulation program
written with MATLAB. The load data are treated as time series data.
They are decomposed into several wavelet coefficient series using
the wavelet transform technique known as Non-decimated Wavelet
Transform (NWT). The reason for using this technique is the belief
in the possibility of extracting hidden patterns from the time series
data. The wavelet coefficient series are used to train the neural
networks (NNs) and used as the inputs to the NNs for electricity load
prediction. The Scale Conjugate Gradient (SCG) algorithm is used as
the learning algorithm for the NNs. To get the final forecast data, the
outputs from the NNs are recombined using the same wavelet
technique. The model was evaluated with the electricity load data of
Electronic Engineering Department in Mandalay Technological
University in Myanmar. The simulation results showed that the
model was capable of producing a reasonable forecasting accuracy in
STLF.
Abstract: Some meta-schedulers query the information system of individual supercomputers in order to submit jobs to the least busy supercomputer on a computational Grid. However, this information can become outdated by the time a job starts due to changes in scheduling priorities. The MSR scheme is based on Multiple Simultaneous Requests and can take advantage of opportunities resulting from these priorities changes. This paper presents the SWARM meta-scheduler, which can speed up the execution of large sets of tasks by minimizing the job queuing time through the submission of multiple requests. Performance tests have shown that this new meta-scheduler is faster than an implementation of the MSR scheme and the gLite meta-scheduler. SWARM has been used through the GridQTL project beta-testing portal during the past year. Statistics are provided for this usage and demonstrate its capacity to achieve reliably a substantial reduction of the execution time in production conditions.