Abstract: In communication networks where communication nodes are connected with finite capacity transmission links, the packet inter-arrival times are strongly correlated with the packet length and the link capacity (or the packet service time). Such correlation affects the system performance significantly, but little attention has been paid to this issue. In this paper, we propose a mathematical framework to study the impact of the correlation between the packet service times and the packet inter-arrival times on system performance. With our mathematical model, we analyze the system performance, e.g., the unfinished work of the system, and show that the correlation affects the system performance significantly. Some numerical examples are also provided.
Abstract: Three similar negative differential resistance (NDR)
profiles with both high peak to valley current density ratio (PVCDR)
value and high peak current density (PCD) value in unity resonant
tunneling electronic circuit (RTEC) element is developed in this paper.
The PCD values and valley current density (VCD) values of the three
NDR curves are all about 3.5 A and 0.8 A, respectively. All PV values
of NDR curves are 0.40 V, 0.82 V, and 1.35 V, respectively. The VV
values are 0.61 V, 1.07 V, and 1.69 V, respectively. All PVCDR
values reach about 4.4 in three NDR curves. The PCD value of 3.5 A
in triple PVCDR RTEC element is better than other resonant
tunneling devices (RTD) elements. The high PVCDR value is
concluded the lower VCD value about 0.8 A. The low VCD value is
achieved by suitable selection of resistors in triple PVCDR RTEC
element. The low PV value less than 1.35 V possesses low power
dispersion in triple PVCDR RTEC element. The designed multiple
value logical level (MVLL) system using triple PVCDR RTEC
element provides equidistant logical level. The logical levels of
MVLL system are about 0.2 V, 0.8 V, 1.5 V, and 2.2 V from low
voltage to high voltage and then 2.2 V, 1.3 V, 0.8 V, and 0.2 V from
high voltage back to low voltage in half cycle of sinusoid wave. The
output level of four levels MVLL system is represented in 0.3 V, 1.1 V,
1.7 V, and 2.6 V, which satisfies the NMP condition of traditional
two-bit system. The remarkable logical characteristic of improved
MVLL system with paralleled capacitor are with four significant
stable logical levels about 220 mV, 223 mV, 228 mV, and 230 mV.
The stability and articulation of logical levels of improved MVLL
system are outstanding. The average holding time of improved MVLL
system is approximately 0.14 μs. The holding time of improved
MVLL system is fourfold than of basic MVLL system. The function of
additional capacitor in the improved MVLL system is successfully
discovered.
Abstract: Ontology-based modelling of multi-formatted
software application content is a challenging area in content
management. When the number of software content unit is huge and
in continuous process of change, content change management is
important. The management of content in this context requires
targeted access and manipulation methods. We present a novel
approach to deal with model-driven content-centric information
systems and access to their content. At the core of our approach is an
ontology-based semantic annotation technique for diversely
formatted content that can improve the accuracy of access and
systems evolution. Domain ontologies represent domain-specific
concepts and conform to metamodels. Different ontologies - from
application domain ontologies to software ontologies - capture and
model the different properties and perspectives on a software content
unit. Interdependencies between domain ontologies, the artifacts and
the content are captured through a trace model. The annotation traces
are formalised and a graph-based system is selected for the
representation of the annotation traces.
Abstract: In this paper optimal capacitor placement problem has
been formulated in a restructured distribution network. In this
scenario the distribution network operator can consider reactive
energy also as a service that can be sold to transmission system. Thus
search for optimal location, size and number of capacitor banks with
the objective of loss reduction, maximum income from selling
reactive energy to transmission system and return on investment for
capacitors, has been performed. Results is influenced with economic
value of reactive energy, therefore problem has been solved for
various amounts of it. The implemented optimization technique is
genetic algorithm. For any value of reactive power economic value,
when reverse of investment index increase and change from zero or
negative values to positive values, the threshold value of selling
reactive power has been obtained. This increasing price of economic
parameter is reasonable until the network losses is less than loss
before compensation.
Abstract: Neoclassical and functionalist explanations of self
organization in multiagent systems have been criticized on several accounts including unrealistic explication of overadapted agents and
failure to resolve problems of externality. The paper outlines a more
elaborate and dynamic model that is capable of resolving these dilemmas. An illustrative example where behavioral diversity is
cobred in a repeated nonzero sum task via evolutionary computing is
presented.
Abstract: Micro power sources are required to be used in autonomous microelectromechanical system (MEMS). In this paper,
we designed and fabricated a three dimensional (3D) MEMS supercapacitor, which is consisting of conformal silicon
dioxide/titanium/polypyrrole (PPy) layers on silicon substrate. At first, ''through-structure'' was fabricated on the silicon substrate by high-aspect-ratio deep reactive ion etching (DRIE) method, which enlarges the available surface area significantly. Then the SiO2/Ti/PPy layers grew sequentially on the ³through-structure´. Finally, the supercapacitor was investigated by electrochemical methods.
Abstract: Fuel cell is an emerging technology in the field
of renewable energy sources which has the capacity to replace
conventional energy generation sources. Fuel cell utilizes hydrogen
energy to produce electricity. The electricity generated by the fuel
cell can’t be directly used for a specific application as it needs
proper power conditioning. Moreover, the output power fluctuates
with different operating conditions. To get a stable output power
at an economic rate, power conditioning circuit is essential for fuel
cell. This paper implements a two-staged power conditioning unit for
fuel cell based distributed generation using hysteresis current control
technique.
Abstract: Content-Based Image Retrieval has been a major area
of research in recent years. Efficient image retrieval with high
precision would require an approach which combines usage of both
the color and texture features of the image. In this paper we propose
a method for enhancing the capabilities of texture based feature
extraction and further demonstrate the use of these enhanced texture
features in Texture-Based Color Image Retrieval.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: Heat pipes are two-phase heat transfer devices with
high effective thermal conductivity. Due to the high heat transport
capacity, heat exchanger with heat pipes has become much smaller
than traditional heat exchangers in handling high heat fluxes. With
the working fluid in a heat pipe, heat can be absorbed on the
evaporator region and transported to the condenser region where the
vapour condenses releasing the heat to the cooling media. Heat pipe
technology has found increasing applications in enhancing the
thermal performance of heat exchangers in microelectranics, energy
saving in HVAC systems for operating rooms,surgery centers, hotels,
cleanrooms etc, temperature regulation systems for the human body
and other industrial sectors. Development activity in heat pipe and
thermosyphon technology in asia in recent years is surveyed. Some
new results obtained in Australia and other countries are also
included.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: The flow field over a flat roof model building has been numerically investigated in order to determine threedimensional CFD guidelines for the calculation of the turbulent flow over a structure immersed in an atmospheric boundary layer. To this purpose, a complete validation campaign has been performed through a systematic comparison of numerical simulations with wind tunnel experimental data. Wind tunnel measurements and numerical predictions have been compared for five different vertical positions, respectively from the upstream leading edge to the downstream bottom edge of the analyzed model. Flow field characteristics in the neighborhood of the building model have been numerically investigated, allowing a quantification of the capabilities of the CFD code to predict the flow separation and the extension of the recirculation regions. The proposed calculations have allowed the development of a preliminary procedure to be used as guidance in selecting the appropriate grid configuration and corresponding turbulence model for the prediction of the flow field over a three-dimensional roof architecture dominated by flow separation.
Abstract: Improving the reactive power and voltage profile of a
distribution substation is investigated in this paper. The purpose is to
properly determination of the shunt capacitors on/off status and
suitable tap changer (TC) position of a substation transformer. In
addition, the limitation of secondary bus voltage, the maximum
allowable number of switching operation in a day for on load tap
changer and on/off status of capacitors are taken into account. To
achieve these goals, an artificial neural network (ANN) is designed to
provide preliminary scheduling. Input of ANN is active and reactive
powers of transformer and its primary and secondary bus voltages.
The output of ANN is capacitors on/off status and TC position. The
preliminary schedule is further refined by fuzzy dynamic
programming in order to reach the final schedule. The operation of
proposed method in Q/V improving is compared with the results
obtained by operator operation in a distribution substation.
Abstract: Poly-β-hydroxybutyrate (PHB) is one of the most
famous biopolymers that has various applications in production of
biodegradable carriers. The most important strategy for enhancing
efficiency in production process and reducing the price of PHB, is the
accurate expression of kinetic model of products formation and
parameters that are effective on it, such as Dry Cell Weight (DCW)
and substrate consumption. Considering the high capabilities of
artificial neural networks in modeling and simulation of non-linear
systems such as biological and chemical industries that mainly are
multivariable systems, kinetic modeling of microbial production of
PHB that is a complex and non-linear biological process, the three
layers perceptron neural network model was used in this study.
Artificial neural network educates itself and finds the hidden laws
behind the data with mapping based on experimental data, of dry cell
weight, substrate concentration as input and PHB concentration as
output. For training the network, a series of experimental data for
PHB production from Hydrogenophaga Pseudoflava by glucose
carbon source was used. After training the network, two other
experimental data sets that have not intervened in the network
education, including dry cell concentration and substrate
concentration were applied as inputs to the network, and PHB
concentration was predicted by the network. Comparison of predicted
data by network and experimental data, indicated a high precision
predicted for both fructose and whey carbon sources. Also in present
study for better understanding of the ability of neural network in
modeling of biological processes, microbial production kinetic of
PHB by Leudeking-Piret experimental equation was modeled. The
Observed result indicated an accurate prediction of PHB
concentration by artificial neural network higher than Leudeking-
Piret model.
Abstract: In this paper, we intend to study the synthesis of the
multibeam arrays. The synthesis implementation-s method for this
type of arrays permits to approach the appropriated radiance-s
diagram. The used approach is based on neural network that are
capable to model the multibeam arrays, consider predetermined
general criteria-s, and finally it permits to predict the appropriated
diagram from the neural model. Our main contribution in this paper is
the extension of a synthesis model of these multibeam arrays.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: In this work a software simulation model has been
proposed for two driven wheels mobile robot path planning; that can
navigate in dynamic environment with static distributed obstacles.
The work involves utilizing Bezier curve method in a proposed N
order matrix form; for engineering the mobile robot path. The Bezier
curve drawbacks in this field have been diagnosed. Two directions:
Up and Right function has been proposed; Probability Recursive
Function (PRF) to overcome those drawbacks.
PRF functionality has been developed through a proposed;
obstacle detection function, optimization function which has the
capability of prediction the optimum path without comparison
between all feasible paths, and N order Bezier curve function that
ensures the drawing of the obtained path.
The simulation results that have been taken showed; the mobile
robot travels successfully from starting point and reaching its goal
point. All obstacles that are located in its way have been avoided.
This navigation is being done successfully using the proposed PRF
techniques.
Abstract: We report a novel fusion tag for expressing
recombinant proteins in E. coli. The fusion tag is the C-terminus part
of the human GMCSF gene comprising 45 amino acids, which aid in
over expression of otherwise non expressible genes. Expression of
hIFN a2b with this fusion tag also escapes the requirement of rare
codons for expression. This is also a first report of a small fusion tag
of human origin having affinity to heparin sepharose column
facilitating the purification of fusion protein.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: Since 2004, we have been developing an in-situ storage image sensor (ISIS) that captures more than 100 consecutive images at a frame rate of 10 Mfps with ultra-high sensitivity as well as the video camera for use with this ISIS. Currently, basic research is continuing in an attempt to increase the frame rate up to 100 Mfps and above. In order to suppress electro-magnetic noise at such high frequency, a digital-noiseless imaging transfer scheme has been developed utilizing solely sinusoidal driving voltages. This paper presents highly efficient-yet-accurate expressions to estimate attenuation as well as phase delay of driving voltages through RC networks of an ultra-high-speed image sensor. Elmore metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE data, we found a simple expression that significantly improves the accuracy of the approximation. Similarly, another simple closed-form model to estimate phase delay through fundamental RC networks is also obtained. Estimation error of both expressions is much less than previous works, only less 2% for most of the cases . The framework of this analysis can be extended to address similar issues of other VLSI structures.