Abstract: Many water desalination technologies have been
developed but in general they are energy intensive and have high cost
and adverse environmental impact. Recently, adsorption technology
for water desalination has been investigated showing the potential of
using low temperature waste heat (50-85oC) thus reducing energy
consumption and CO2 emissions. This work mathematically
compares the performance of an adsorption cycle that produces two
useful effects namely, fresh water and cooling using two different
adsorbents, silica-gel and an advanced zeolite material AQSOA-ZO2,
produced by Mitsubishi plastics. It was found that at low chilled
water temperatures, typically below 20oC, the AQSOA-Z02 is more
efficient than silica-gel as the cycle can produce 5.8 m3 of fresh water
per day and 50.1 Rton of cooling per tonne of AQSOA-ZO2. Above
20oC silica-gel is still better as the cycle production reaches 8.4 m3
per day and 62.4 Rton per tonne of silica-gel. These results show the
potential of using the AQSOA-Z02 at low chilled water temperature
for water desalination and cooling applications.
Abstract: Failure of typical seismic frames has been found by
plastic hinge occurring on beams section near column faces. On the
other hand, the seismic capacity of the frames can be enhanced if the
plastic hinges of the beams are shifted away from the column faces.
This paper presents detailing of reinforcements in the interior beam–
column connections aiming to relocate the plastic hinge of reinforced
concrete and precast concrete frames. Four specimens were tested
under quasi-static cyclic load including two monolithic specimens
and two precast specimens. For one monolithic specimen, typical
seismic reinforcement was provided and considered as a reference
specimen named M1. The other reinforced concrete frame M2
contained additional intermediate steel in the connection area
compared with the specimen M1. For the precast specimens,
embedded T-section steels in joint were provided, with and without
diagonal bars in the connection area for specimen P1 and P2,
respectively. The test results indicated the ductile failure with beam
flexural failure in monolithic specimen M1 and the intermediate steel
increased strength and improved joint performance of specimen M2.
For the precast specimens, cracks generated at the end of the steel
inserts. However, slipping of reinforcing steel lapped in top of the
beams was seen before yielding of the main bars leading to the brittle
failure. The diagonal bars in precast specimens P2 improved the
connection stiffness and the energy dissipation capacity.
Abstract: In this paper, an analytical simplified method for
calculating elasto-plastic stresses strains of notched bodies subject to
non-proportional loading paths is discussed. The method was based
on the Neuber notch correction, which relates the incremental elastic
and elastic-plastic strain energy densities at the notch root and the
material constitutive relationship. The validity of the method was
presented by comparing computed results of the proposed model
against finite element numerical data of notched shaft. The
comparison showed that the model estimated notch-root elasto-plastic
stresses strains with good accuracy using linear-elastic stresses. The
prosed model provides more efficient and simple analysis method
preferable to expensive experimental component tests and more
complex and time consuming incremental non-linear FE analysis.
The model is particularly suitable to perform fatigue life and fatigue
damage estimates of notched components subjected to nonproportional
loading paths.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: This paper is part of a study to develop robots for
farming. As such power requirement to operate equipment attach to
such robots become an important factor. Soil-tool interaction plays
major role in power consumption, thus predicting accurately the
forces which act on the blade during the farming is very important for
optimal designing of farm equipment. In this paper, a finite element
investigation for tillage tools and soil interaction is described by
using an inelastic constitutive material law for agriculture
application. A 3-dimensional (3D) nonlinear finite element analysis
(FEA) is developed to examine behavior of a blade with different
rake angles moving in a block of soil, and to estimate the blade force.
The soil model considered is an elastic-plastic with non-associated
Drucker-Prager material model. Special use of contact elements are
employed to consider connection between soil-blade and soil-soil
surfaces. The FEA results are compared with experimental ones,
which show good agreement in accurately predicting draft forces
developed on the blade when it moves through the soil. Also a very
good correlation was obtained between FEA results and analytical
results from classical soil mechanics theories for straight blades.
These comparisons verified the FEA model developed. For analyzing
complicated soil-tool interactions and for optimum design of blades,
this method will be useful.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: This paper presents effects of distilled water, seawater
and sustained bending strains of 30% and 50% ultimate strain at
room temperature, on the durability of unidirectional pultruded
carbon fiber reinforced polymer (CFRP) plates. In this study,
dynamic mechanical analyzer (DMA) was used to investigate the
synergic effects of the immersions and bending strains on the viscoelastic
properties of (CFRP) such as storage modulus, tan delta and
glass transition temperature. The study reveals that the storage
modulus and glass transition temperature increase while tan delta
peak decreases in the initial stage of both immersions due to the
progression of curing. The storage modulus and Tg subsequently
decrease and tan delta increases due to the matrix plasticization. The
blister induced damages in the unstrained seawater samples enhance
water uptake and cause more serious degradation of Tg and storage
modulus than in water immersion. Increasing sustained bending
decreases Tg and storage modulus in a long run for both immersions
due to resin matrix cracking and debonding. The combined effects of
immersions and strains are not clearly reflected due to the statistical
effects of DMA sample sizes and competing processes of molecular
reorientation and postcuring.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: Neuroplasticity or the flexibility of the neural system
is the ability of the brain to adapt to the lack or deterioration of sense
and the capability of the neural system to modify itself through
changing shape and function. Not only have studies revealed that
neuroplasticity does not end in childhood, but also they have proven
that it continues till the end of life and is not limited to the neural
system and covers the cognitive system as well. In the field of
cognition, neuroplasticity is defined as the ability to change old
thoughts according to new conditions and the individuals' differences
in using various styles of cognitive regulation inducing several social,
emotional and cognitive outcomes. This paper attempts to discuss and
define major theories and principles of neuroplasticity and elaborate
on nature or nurture.
Abstract: The key role in phenomenological modelling of cyclic
plasticity is good understanding of stress-strain behaviour of given
material. There are many models describing behaviour of materials
using numerous parameters and constants. Combination of individual
parameters in those material models significantly determines whether
observed and predicted results are in compliance. Parameter
identification techniques such as random gradient, genetic algorithm
and sensitivity analysis are used for identification of parameters using
numerical modelling and simulation. In this paper genetic algorithm
and sensitivity analysis are used to study effect of 4 parameters of
modified AbdelKarim-Ohno cyclic plasticity model. Results
predicted by Finite Element (FE) simulation are compared with
experimental data from biaxial ratcheting test with semi-elliptical
loading path.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: In this paper we present the efficient parallel
implementation of elastoplastic problems based on the TFETI (Total
Finite Element Tearing and Interconnecting) domain decomposition
method. This approach allow us to use parallel solution and compute
this nonlinear problem on the supercomputers and decrease the
solution time and compute problems with millions of DOFs. In
our approach we consider an associated elastoplastic model with
the von Mises plastic criterion and the combination of linear
isotropic-kinematic hardening law. This model is discretized by
the implicit Euler method in time and by the finite element
method in space. We consider the system of nonlinear equations
with a strongly semismooth and strongly monotone operator. The
semismooth Newton method is applied to solve this nonlinear
system. Corresponding linearized problems arising in the Newton
iterations are solved in parallel by the above mentioned TFETI. The
implementation of this problem is realized in our in-house MatSol
packages developed in MatLab.
Abstract: Since the initial creation of the Barbie doll in 1959, it
became a symbol of US society. Likewise, the Licca-chan, a Japanese
doll created in 1967, also became a Japanese symbolic doll of Japanese
society. Prior to the introduction of Licca-chan, Barbie was already
marketed in Japan but their sales were dismal. Licca-chan (an actual
name: Kayama Licca) is a plastic doll with a variety of sizes ranging
from 21.0 cm to 29.0 cm which many Japanese girls dream of having.
For over 35 years, the manufacturer, Takara Co., Ltd. has sold over 48
million dolls and has produced doll houses, accessories, clothes, and
Licca-chan video games for the Nintendo DS. Many First-generation
Licca-chan consumers still are enamored with Licca-chan, and go to
Licca-chan House, in an amusement park with their daughters. These
people are called Licca-chan maniacs, as they enjoy touring the
Licca-chan’s factory in Tohoku or purchase various Licca-chan
accessories. After the successful launch of Licca-chan into the
Japanese market, a mixed-like doll from the US and Japan, a doll,
JeNny, was later sold in the same Japanese market by Takara Co., Ltd.
in 1982.
Comparison of these cultural iconic dolls, Barbie and Licca-chan,
are analyzed in this paper. In fact, these dolls have concepts of girls’
dreams. By using concepts of mythology of Jean Baudrillard, these
dolls can be represented idealized images of figures in the products for
consumers, but at the same time, consumers can see products with
different perspectives, which can cause controversy.
Abstract: Today, the pollution due to non-degradable material
such as plastics, has led to studies about the development of
environmental-friendly material. Because of biodegradability
obtained from natural sources, polylactid acid (PLA) and ijuk fiber
are interesting to modify into a composite. This material is also
expected to reduce the impact of environmental pollution. Surface
modification of ijuk fiber through alkalinization with 0.25 M NaOH
solution for 30 minutes was aimed to enhance its compatibility to
PLA, in order to improve properties of the composite such as the
mechanical properties. Alkalinization of the ijuk fibers annihilates
some surface components such as lignin, wax and hemicelloluse, so
the pore on the surface clearly appeared, decreasing of the density
and diameter of the ijuk fibers. The change of the ijuk fiber properties
leads to increase the mechanical properties of PLA composites
reinforced the ijuk fibers through strengthening of the mechanical
interlocking with the PLA matrix. An addition to enhance the
distribution of the fibers in the PLA matrix, the stirring during DCM
solvent evaporation from the mixture of the ijuk fibers and the
dissolved-PLA can reduce amount of the trapped-voids and fibers
pull-out phenomena, which can decrease the mechanical properties of
the composite.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: PLA emerged as a promising polymer because of its
property as a compostable, biodegradable thermoplastic made from
renewable sources. PLA can be polymerized from monomers
(Lactide or Lactic acid) obtained by fermentation processes from
renewable sources such as corn starch or sugarcane. For PLA
synthesis, ring opening polymerization (ROP) of Lactide monomer is
one of the preferred methods. In the literature, the technique mainly
developed for ROP of PLA is based on metal/bimetallic catalyst (Sn,
Zn and Al) or other organic catalysts in suitable solvent. However,
the PLA synthesized using such catalysts may contain trace elements
of the catalyst which may cause toxicity. This work estimated the
usefulness and drawbacks of using different catalysts as well as effect
of alternative energies and future aspects for PLA production.