Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: It is necessary to incorporate technological advances
achieved in the field of engineering into dentistry in order to enhance
the process of diagnosis, treatment planning and enable the doctors to
render better treatment to their patients. To achieve this ultimate goal
long distance collaborations are often necessary. This paper discusses
the various collaborative tools and their applications to solve a few
burning problems confronted by the dentists. Customization is often
the solution to most of the problems. But rapid designing,
development and cost effective manufacturing is a difficult task to
achieve. This problem can be solved using the technique of digital
manufacturing. Cases from 6 major branches of dentistry have been
discussed and possible solutions with the help of state of art
technology using rapid digital manufacturing have been proposed in
the present paper. The paper also entails the usage of existing tools in
collaborative and digital manufacturing area.
Abstract: Automated material handling is given prime
importance in the semi automated and automated facilities since it
provides solution to the gigantic problems related to inventory and
also support the latest philosophies like just in time production JIT
and lean production. Automated storage and retrieval system is an
antidote (if designed properly) to the facility sufferings like getting
the right material , materials getting perished, long cycle times or
many other similar kind of problems. A working model of automated
storage and retrieval system (AS/RS) is designed and developed
under the design parameters specified by Material Handling Industry
of America (MHIA). Later on analysis was carried out to calculate
the throughput and size of the machine. The possible implementation
of this technology in local scenario is also discussed in this paper.
Abstract: Climate change is a cumulative change in weather
patterns over a period of time. Trend analysis using non-parametric
Mann-Kendall test may help to determine the existence and
magnitude of any statistically significant trend in the climatic data.
Another index called Sen slope may be used to quantify the
magnitude of such trends. A toolbar extension to ESRI ArcGIS
named Arc Trends has been developed in this study for performing
the above mentioned tasks. To study the temporal trend of
meteorological parameters, 32 years (1971-2002) monthly
meteorological data were collected for 133 selected stations over
different agro-ecological regions of India. Both the maximum and
minimum temperatures were found to be rising. A significant
increasing trend in the relative humidity and a consistent significant
decreasing trend in the wind speed all over the country were found.
However, a general increase in rainfall was not found in recent years.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: Video sensor networks operate on stringent requirements
of latency. Packets have a deadline within which they have
to be delivered. Violation of the deadline causes a packet to be
treated as lost and the loss of packets ultimately affects the quality
of the application. Network latency is typically a function of many
interacting components. In this paper, we propose ways of reducing
the forwarding latency of a packet at intermediate nodes. The
forwarding latency is caused by a combination of processing delay
and queueing delay. The former is incurred in order to determine the
next hop in dynamic routing. We show that unless link failures in a
very specific and unlikely pattern, a vast majority of these lookups
are redundant. To counter this we propose source routing as the
routing strategy. However, source routing suffers from issues related
to scalability and being impervious to network dynamics. We propose
solutions to counter these and show that source routing is definitely
a viable option in practical sized video networks. We also propose a
fast and fair packet scheduling algorithm that reduces queueing delay
at the nodes. We support our claims through extensive simulation on
realistic topologies with practical traffic loads and failure patterns.
Abstract: This paper presents the findings of two experiments that were performed on the Redundancy in Wireless Connection Model (RiWC) using the 802.11b standard. The experiments were simulated using OPNET 11.5 Modeler software. The first was aimed at finding the maximum number of simultaneous Voice over Internet Protocol (VoIP) users the model would support under the G.711 and G.729 codec standards when the packetization interval was 10 milliseconds (ms). The second experiment examined the model?s VoIP user capacity using the G.729 codec standard along with background traffic using the same packetization interval as in the first experiment. To determine the capacity of the model under various experiments, we checked three metrics: jitter, delay and data loss. When background traffic was added, we checked the response time in addition to the previous three metrics. The findings of the first experiment indicated that the maximum number of simultaneous VoIP users the model was able to support was 5, which is consistent with recent research findings. When using the G.729 codec, the model was able to support up to 16 VoIP users; similar experiments in current literature have indicated a maximum of 7 users. The finding of the second experiment demonstrated that the maximum number of VoIP users the model was able to support was 12, with the existence of background traffic.
Abstract: Software crisis refers to the situation in which the developers are not able to complete the projects within time and budget constraints and moreover these overscheduled and over budget projects are of low quality as well. Several methodologies have been adopted form time to time to overcome this situation and now in the focus is component based software engineering. In this approach, emphasis is on reuse of already existing software artifacts. But the results can not be achieved just by preaching the principles; they need to be practiced as well. This paper highlights some of the very basic elements of this approach, which has to be in place to get the desired goals of high quality, low cost with shorter time-to-market software products.
Abstract: A behavioral model of a second order switchedcapacitor Sigma-Delta modulator is presented. The purpose of this work is the presentation of a behavioral model of a second order switched capacitor ΣΔ modulator considering (Error due to Clock Jitter, Thermal noise Amplifier Noise, Amplifier Slew-Rate, Non linearity of amplifiers, Gain error, Charge Injection, Clock Feedthrough, and Nonlinear on-resistance). A comparison between the use of MOS switches and the use transmission gate switches use is analyzed.
Abstract: In this paper, we propose a solution to the motion
control problem of a 2-link revolute manipulator arm. We require the
end-effector of the arm to move safely to its designated target in a
priori known workspace cluttered with fixed circular obstacles of
arbitrary position and sizes. Firstly a unique velocity algorithm is
used to move the end-effector to its target. Secondly, for obstacle
avoidance a turning angle is designed, which when incorporated into
the control laws ensures that the entire robot arm avoids any number
of fixed obstacles along its path enroute the target. The control laws
proposed in this paper also ensure that the equilibrium point of the
system is asymptotically stable. Computer simulations of the
proposed technique are presented.
Abstract: The leisure boatbuilding industry has tight profit margins that demand that boats are created to a high quality but with low cost. This requirement means reduced design times combined with increased use of design for production can lead to large benefits. The evolutionary nature of the boatbuilding industry can lead to a large usage of previous vessels in new designs. With the increase in automated tools for concurrent engineering within structural design it is important that these tools can reuse this information while subsequently feeding this to designers. The ability to accurately gather this materials and parts data is also a key component to these tools. This paper therefore aims to develop an architecture made up of neural networks and databases to feed information effectively to the designers based on previous design experience.
Abstract: Particle detection in very noisy and low contrast images
is an active field of research in image processing. In this article, a
method is proposed for the efficient detection and sizing of subsurface
spherical particles, which is used for the processing of softly fused
Au nanoparticles. Transmission Electron Microscopy is used for
imaging the nanoparticles, and the proposed algorithm has been
tested with the two-dimensional projected TEM images obtained.
Results are compared with the data obtained by transmission optical
spectroscopy, as well as with conventional circular object detection
algorithms.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: In this paper, we propose a Perceptually Optimized Embedded ZeroTree Image Coder (POEZIC) that introduces a perceptual weighting to wavelet transform coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to the coding quality obtained using the SPIHT algorithm only. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEZIC quality assessment. Our POEZIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) luminance masking and Contrast masking, 2) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting, 3) the Wavelet Error Sensitivity WES used to reduce the perceptual quantization errors. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: This research aims to analyze the regenerative burner and the recuperative burner for the different reheating furnaces in the steel industry. The warm air temperatures of the burners are determined to suit with the sizes of the reheating furnaces by considering the air temperature, the fuel cost and the investment cost. The calculations of the payback period and the net present value are studied to compare the burners for the different reheating furnaces. The energy balance is utilized to calculate and compare the energy used in the different sizes of reheating furnaces for each burner. It is found that the warm air temperature is different if the sizes of reheating furnaces are varied. Based on the considerations of the net present value and the payback period, the regenerative burner is suitable for all plants at the same life of the burner. Finally, the sensitivity analysis of all factors has been discussed in this research.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.
Abstract: This study demonstrates the use of Class F fly ash in
combination with lime or lime kiln dust in the full depth reclamation
(FDR) of asphalt pavements. FDR, in the context of this paper, is a
process of pulverizing a predetermined amount of flexible pavement
that is structurally deficient, blending it with chemical additives and
water, and compacting it in place to construct a new stabilized base
course. Test sections of two structurally deficient asphalt pavements
were reclaimed using Class F fly ash in combination with lime and
lime kiln dust. In addition, control sections were constructed using
cement, cement and emulsion, lime kiln dust and emulsion, and mill
and fill. The service performance and structural behavior of the FDR
pavement test sections were monitored to determine how the fly ash
sections compared to other more traditional pavement rehabilitation
techniques. Service performance and structural behavior were
determined with the use of sensors embedded in the road and Falling
Weight Deflectometer (FWD) tests. Monitoring results of the FWD
tests conducted up to 2 years after reclamation show that the cement,
fly ash+LKD, and fly ash+lime sections exhibited two year resilient
modulus values comparable to open graded cement stabilized
aggregates (more than 750 ksi). The cement treatment resulted in a
significant increase in resilient modulus within 3 weeks of
construction and beyond this curing time, the stiffness increase was
slow. On the other hand, the fly ash+LKD and fly ash+lime test
sections indicated slower shorter-term increase in stiffness. The fly
ash+LKD and fly ash+lime section average resilient modulus values
at two years after construction were in excess of 800 ksi. Additional
longer-term testing data will be available from ongoing pavement
performance and environmental condition data collection at the two
pavement sites.
Abstract: A new digital transceiver circuit for asynchronous frame detection is proposed where both the transmitter and receiver contain all digital components, thereby avoiding possible use of conventional devices like monostable multivibrators with unstable external components such as resistances and capacitances. The proposed receiver circuit, in particular, uses a combinational logic block yielding an output which changes its state as soon as the start bit of a new frame is detected. This, in turn, helps in generating an efficient receiver sampling clock. A data latching circuit is also used in the receiver to latch the recovered data bits in any new frame. The proposed receiver structure is also extended from 4- bit information to any general n data bits within a frame with a common expression for the output of the combinational logic block. Performance of the proposed hardware design is evaluated in terms of time delay, reliability and robustness in comparison with the standard schemes using monostable multivibrators. It is observed from hardware implementation that the proposed circuit achieves almost 33 percent speed up over any conventional circuit.