Abstract: Thermoacoustic instabilities in combustors have
remained a topic of investigation for over a few decades due to the
challenges it posses to the operation of low emission gas turbines.
For combustors burning liquid fuel, understanding the cause-andeffect
relationship between spray combustion dynamics and
thermoacoustic oscillations is imperative for the successful
development of any control methodology for its mitigation. The
paper presents some very unique operating characteristics of a
kerosene-fueled diffusion type combustor undergoing limit-cycle
oscillations. Combustor stability limits were mapped using three
different-sized injectors. The results show that combustor instability
depends on the characteristics of the fuel spray. A simple analytic
analysis is also reported in support of a plausible explanation for the
unique combustor behavior. The study indicates that high amplitude
acoustic pressure in the combustor may cause secondary breakdown
of fuel droplets resulting in premixed pre-vaporized type burning of
the diffusion type combustor.
Abstract: Many studies have emphasized the importance of
resistive exercise to maintain a healthy human body, particular in
prevention of weakening of physical strength. Recently, some studies
advocated that an application of vibration as a supplementary means in
a regular training was effective in encouraging physical strength. Aim
of the current study was, therefore, to identify if an application of
vibration in a resistive exercise was effective in encouraging physical
strength as that in a regular training. A 3-dimensional virtual lower
extremity model for a healthy male and virtual leg-press model were
generated and synchronized. Dynamic leg-press exercises on a slide
machine with/without extra load and on a footboard with vibration as
well as on a slide machine with extra load were analyzed. The results
of the current indicated that the application of the vibration on the
dynamic leg-press exercise might be not greatly effective in
encouraging physical strength, compared with the dynamic leg press
exercise with extra load. It was, however, thought that the application
of the vibration might be helpful to elderly individuals because the
reduced maximum muscle strength appeared by the effect of the
vibration may avoid a muscular spasm, which can be driven from a
high muscle strength sometimes produced during the leg-press
exercise with extra load.
Abstract: In this study, three strains of Vibrio parahaemolyticus
(690, BCRC 13023 and BCRC 13025) were subjected to acid
adaptation at pH 5.5 for 90 min. The survival of acid-adapted and
non-adapted V. parahaemolyticus strains under simulated gastric
condition and their protein expression profiles were investigated.
Results showed that acid adaptation increased the survival of the test
V. parahaemolyticus strains after exposure to simulated gastric juice
(pH 3). Additionally, acid adaptation also affected the protein
expression in these V. parahaemolyticus strains. Nine proteins,
identified as atpA, atpB, DnaK, GroEL, OmpU, enolase,
fructose-bisphosphate aldolase, phosphoglycerate kinase and
triosephosphate isomerase, were induced by acid adaptation in two or
three of the test strains. These acid-adaptive proteins may play
important regulatory roles in the acid tolerance response (ATR) of V.
parahaemolyticus.
Abstract: A new estimator for evolutionary spectrum (ES) based
on short time Fourier transform (STFT) and modified group delay
function (MGDF) by signal decomposition (SD) is proposed. The
STFT due to its built-in averaging, suppresses the cross terms and the
MGDF preserves the frequency resolution of the rectangular window
with the reduction in the Gibbs ripple. The present work overcomes
the magnitude distortion observed in multi-component non-stationary
signals with STFT and MGDF estimation of ES using SD. The SD is
achieved either through discrete cosine transform based harmonic
wavelet transform (DCTHWT) or perfect reconstruction filter banks
(PRFB). The MGDF also improves the signal to noise ratio by
removing associated noise. The performance of the present method is
illustrated for cross chirp and frequency shift keying (FSK) signals,
which indicates that its performance is better than STFT-MGDF
(STFT-GD) alone. Further its noise immunity is better than STFT.
The SD based methods, however cannot bring out the frequency
transition path from band to band clearly, as there will be gap in the
contour plot at the transition. The PRFB based STFT-SD shows good
performance than DCTHWT decomposition method for STFT-GD.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: Numerical integration of initial boundary problem for advection equation in 3 ℜ is considered. The method used is
conditionally stable semi-Lagrangian advection scheme with high order interpolation on unstructured mesh. In order to increase time step integration the BFECC method with limiter TVD correction is used. The method is adopted on parallel graphic processor unit environment using NVIDIA CUDA and applied in Navier-Stokes solver. It is shown that the calculation on NVIDIA GeForce 8800
GPU is 184 times faster than on one processor AMDX2 4800+ CPU. The method is extended to the incompressible fluid dynamics solver. Flow over a Cylinder for 3D case is compared to the experimental data.
Abstract: This paper explores the social and political imperatives in the sphere of public policy relating to social justice. In India, the colonial legacy and post-colonial social and political pressures sustained the appropriation of 'caste' category in allocating public resources to the backward class of citizens. For several reasons, 'economic' category could not be placed in allocating resources. This paper examines the reasons behind the deliberative exercises and formulating policies and seeks an alternative framework in realizing social justice in terms of a unified category. This attempt can be viewed as a reconciliation of traditional and modern values for a viable alternative in public policy making.
Abstract: The binary phase-only filter digital watermarking
embeds the phase information of the discrete Fourier transform of the
image into the corresponding magnitudes for better image authentication.
The paper proposed an approach of how to implement watermark
embedding by quantizing the magnitude, with discussing how to
regulate the quantization steps based on the frequencies of the magnitude
coefficients of the embedded watermark, and how to embed the
watermark at low frequency quantization. The theoretical analysis and
simulation results show that algorithm flexibility, security, watermark
imperceptibility and detection performance of the binary phase-only
filter digital watermarking can be effectively improved with quantization
based watermark embedding, and the robustness against JPEG
compression will also be increased to some extent.
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: The purpose of this study is to explore how the emotions at the moment of conflict escalation are expressed nonverbally and how it can be detected by the parties involved in the conflicting situation. The study consists of two parts, in the first part it starts with the definition of "conflict" and "nonverbal communication". Further it includes the analysis of emotions and types of emotions, which may bring to the conflict escalation. Four types of emotions and emotion constructs are analyzed, particularly fear, anger, guilt and frustration. The second part of the study analyses the general role of nonverbal behavior in interaction and communication, which information it may give during communication to the person, who sends or receives those signals. The study finishes with the analysis of the nonverbal expression of analyzed emotions and on how it can be used during interaction.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: A analysis on the conventional the blood pressure estimation method using an oscillometric sphygmomanometer was
performed through a computer simulation using an arterial pressure-volume (APV) model. Traditionally, the maximum amplitude algorithm (MAP) was applied on the oscillation waveforms of the APV model to obtain the mean arterial pressure and the characteristic ratio. The estimation of mean arterial pressure and
characteristic ratio was significantly affected with the shape of the blood pressure waveforms and the cutoff frequency of high-pass filter
(HPL) circuitry. Experimental errors are due to these effects when estimating blood pressure. To find out an algorithm independent from
the influence of waveform shapes and parameters of HPL, the volume
oscillation of the APV model and the phase shift of the oscillation with fast fourier transform (FFT) were testified while increasing the cuff
pressure from 1 mmHg to 200 mmHg (1 mmHg per second). The phase shift between the ranges of volume oscillation was then only observed between the systolic and the diastolic blood pressures. The same results were also obtained from the simulations performed on two different the arterial blood pressure waveforms and one
hyperthermia waveform.
Abstract: This study describes the methodology for the development of a validated in-vitro in-vivo correlation (IVIVC) for metoprolol tartrate modified release dosage forms with distinctive release rate characteristics. Modified release dosage forms were formulated by microencapsulation of metoprolol tartrate into different amounts of ethylcellulose by non-solvent addition technique. Then in-vitro and in-vivo studies were conducted to develop and validate level A IVIVC for metoprolol tartrate. The values of regression co-efficient (R2-values) for IVIVC of T2 and T3 formulations were not significantly (p
Abstract: The investigation results of high-density hydrogen
heating by high-current electric arc are presented at initial pressure
from 5 MPa to 160 MPa with current amplitude up to 1.6 MA and
current rate of rise 109-1011 A/s. When changing the initial pressure
and current rate of rise, channel temperature varies from several
electronvolts to hundreds electronvolts. Arc channel radius is several
millimeters. But the radius of the discharge chamber greater than the
radius of the arc channel on approximately order of magnitude. High
efficiency of gas heating is caused by radiation absorption of
hydrogen surrounding the arc. Current channel consist from vapor of
the initiating wire. At current rate of rise of 109 A/s and relatively
small current amplitude gas heating occurs due to radiation
absorption in the band transparency of hydrogen by the wire vapours
with photon energies less than 13.6 eV. At current rate of rise of
1011 A/s gas heating is due to hydrogen absorption of soft X-rays
from discharge channel.
Abstract: A novel robust audio watermarking scheme is
proposed in this paper. In the proposed scheme, the host audio signals
are segmented into frames. Two consecutive frames are assessed if
they are suitable to represent a watermark bit. If so, frequency
transform is performed on these two frames. The compressionexpansion
technique is adopted to generate distortion over the two
frames. The distortion is used to represent one watermark bit.
Psychoacoustic model is applied to calculate local auditory mask to
ensure that the distortion is not audible. The watermarking schemes
using mono and stereo audio signals are designed differently. The
correlation-based detection method is used to detect the distortion
and extract embedded watermark bits. The experimental results show
that the quality degradation caused by the embedded watermarks is
perceptually transparent and the proposed schemes are very robust
against different types of attacks.
Abstract: In this paper a new approach to prioritize urban planning projects in an efficient and reliable way is presented. It is based on environmental pressure indices and multicriteria decision methods. The paper introduces a rigorous method with acceptable complexity of rank ordering urban development proposals according to their environmental pressure. The technique combines the use of Environmental Pressure Indicators, the aggregation of indicators in an Environmental Pressure Index by means of the Analytic Network Process method and interpreting the information obtained from the experts during the decision-making process. The ANP method allows the aggregation of the experts- judgments on each of the indicators into one Environmental Pressure Index. In addition, ANP is based on utility ratio functions which are the most appropriate for the analysis of uncertain data, like experts- estimations. Finally, unlike the other multicriteria techniques, ANP allows the decision problem to be modelled using the relationships among dependent criteria. The method has been applied to the proposal for urban development of La Carlota airport in Caracas (Venezuela). The Venezuelan Government would like to see a recreational project develop on the abandoned area and mean a significant improvement for the capital. There are currently three options on their table which are currently under evaluation. They include a Health Club, a Residential area and a Theme Park. The participating experts coincided in the appreciation that the method proposed in this paper is useful and an improvement from traditional techniques such as environmental impact studies, lifecycle analysis, etc. They find the results obtained coherent, the process seems sufficiently rigorous and precise, and the use of resources is significantly less than in other methods.
Abstract: Fiber optic sensor technology offers the possibility of
sensing different parameters like strain, temperature, pressure in
harsh environment and remote locations. these kinds of sensors
modulates some features of the light wave in an optical fiber such an
intensity and phase or use optical fiber as a medium for transmitting
the measurement information.
The advantages of fiber optic sensors in contrast to conventional
electrical ones make them popular in different applications and now a
day they consider as a key component in improving industrial
processes, quality control systems, medical diagnostics, and
preventing and controlling general process abnormalities.
This paper is an introduction to fiber optic sensor technology and
some of the applications that make this branch of optic technology,
which is still in its early infancy, an interesting field.
Abstract: This paper is devoted to present and discuss a model that allows a local segmentation by using statistical information of a given image. It is based on Chan-Vese model, curve evolution, partial differential equations and binary level sets method. The proposed model uses the piecewise constant approximation of Chan-Vese model to compute Signed Pressure Force (SPF) function, this one attracts the curve to the true object(s)-s boundaries. The implemented model is used to extract weld defects from weld radiographic images in the aim to calculate the perimeter and surfaces of those weld defects; encouraged resultants are obtained on synthetic and real radiographic images.
Abstract: Well-developed strategic marketing planning is the essential
prerequisite for establishment of the right and unique competitive
advantage. Typical market, however, is a heterogeneous
and decentralized structure with natural involvement of individual
or group subjectivity and irrationality. These features cannot be
fully expressed with one-shot rigorous formal models based on,
e.g. mathematics, statistics or empirical formulas. We present an
innovative solution, extending the domain of agent based computational
economics towards the concept of hybrid modeling in service
provider and consumer market such as telecommunications. The
behavior of the market is described by two classes of agents -
consumer and service provider agents - whose internal dynamics
are fundamentally different. Customers are rather free multi-state
structures, adjusting behavior and preferences quickly in accordance
with time and changing environment. Producers, on the contrary,
are traditionally structured companies with comparable internal processes
and specific managerial policies. Their business momentum is
higher and immediate reaction possibilities limited. This limitation
underlines importance of proper strategic planning as the main
process advising managers in time whether to continue with more
or less the same business or whether to consider the need for future
structural changes that would ensure retention of existing customers
or acquisition of new ones.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.