Abstract: This article deals with numerical simulation of the
floor heating convector in 3D. Numerical simulation is focused on
cooling mode of the floor heating convector. Geometrical model
represents section of the heat exchanger – two fins with the gap
between, pipes are not involved. Two types of fin are examined –
sinusoidal and angular shape with different fin spacing. Results of fin
spacing in case of constant Reynolds number are presented. For the
numerical simulation was used commercial software Ansys Fluent.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: This project aims to investigate the potential of
torrefaction to improve the properties of Malaysian palm kernel shell
(PKS) as a solid fuel. A study towards torrefaction of PKS was
performed under various temperature and residence time of 240, 260,
and 280oC and 30, 60, and 90 minutes respectively. The torrefied
PKS was characterized in terms of the mass yield, energy yield,
elemental composition analysis, calorific value analysis, moisture and
volatile matter contents, and ash and fixed carbon contents. The mass
and energy yield changes in the torrefied PKS were observed to
prove that the temperature has more effect compare to residence time
in the torrefaction process. The C content of PKS increases while H
and O contents decrease after torrefaction, which resulted in higher
heating value between 5 to 16%. Meanwhile, torrefaction caused the
ash and fixed carbon content of PKS to increase, and the moisture
and volatile matter to decrease.
Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: Combined conduction-free convection heat transfer in
vertical eccentric annuli is numerically investigated using a finitedifference
technique. Numerical results, representing the heat transfer
parameters such as annulus walls temperature, heat flux, and heat
absorbed in the developing region of the annulus, are presented for a
Newtonian fluid of Prandtl number 0.7, fluid-annulus radius ratio 0.5,
solid-fluid thermal conductivity ratio 10, inner and outer wall
dimensionless thicknesses 0.1 and 0.2, respectively, and
dimensionless eccentricities 0.1, 0.3, 0.5, and 0.7. The annulus walls
are subjected to thermal boundary conditions, which are obtained by
heating one wall isothermally whereas keeping the other wall at inlet
fluid temperature. In the present paper, the annulus heights required
to achieve thermal full development for prescribed eccentricities are
obtained. Furthermore, the variation in the height of thermal full
development as function of the geometrical parameter, i.e.,
eccentricity is also investigated.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: Recently ORC(Organic Rankine Cycle) has attracted
much attention due to its potential in reducing consumption of fossil
fuels and its favorable characteristics to exploit low-grade heat sources.
In this work thermodynamic performance of ORC with superheating of
vapor is comparatively assessed for various working fluids. Special
attention is paid to the effects of system parameters such as the evaporating
temperature and the turbine inlet temperature on the characteristics
of the system such as maximum possible work extraction from
the given source, volumetric flow rate per 1 kW of net work and
quality of the working fluid at turbine exit as well as thermal and
exergy efficiencies. Results show that for a given source the thermal
efficiency increases with decrease of the superheating but exergy
efficiency may have a maximum value with respect to the superheating
of the working fluid. Results also show that in selection of working
fluid it is required to consider various criteria of performance characteristics
as well as thermal efficiency.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: The effect of cross linking of the protein isolates of
three legumes with the microbial enzyme transglutaminase (EC
2.3.2.13) on the functional properties at different NaCl concentration
was studied. The reduction in the total free amino groups (OD340) of
the polymerized protein showed that TGase treatment cross-linking
the protein subunit of each legume. The solubility of the protein
polymer of each legume was greatly improved at high concentration
of NaCl. At 1.2 M NaCl the solubility of the native legumes protein
was significantly decreased but after polymerization slightly
improved. Cross linked proteins were less turbid on heating to higher
temperature as compared to native proteins and the temperature at
which the protein turns turbid also increased in the polymerized
proteins. The emulsifying and foaming properties of the protein
polymer were greatly improved at all concentrations of NaCl for all
legumes.
Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.