Abstract: Motion estimation is the most computationally
intensive part in video processing. Many fast motion estimation
algorithms have been proposed to decrease the computational
complexity by reducing the number of candidate motion vectors.
However, these studies are for fast search algorithms themselves while
almost image and video compressions are operated with software
based. Therefore, the timing constraints for running these motion
estimation algorithms not only challenge for the video codec but also
overwhelm for some of processors. In this paper, the performance of
motion estimation is enhanced by using Intel's Streaming SIMD
Extension 2 (SSE2) technology with Intel Pentium 4 processor.
Abstract: In this paper, computational fluid dynamics (CFD) is utilized to characterize a prototype biolistic delivery system, the biomedical device based on the contoured-shock-tube design (CST), with the aim at investigating shocks induced flow instabilities within the contoured shock tube. The shock/interface interactions, the growth of perturbation at an interface between two fluids of different density are interrogated. The key features of the gas dynamics and gas-particle interaction are discussed
Abstract: Aligned and random nanofibrous scaffolds of PVA/PCL/nHA were fabricated by electrospinning method. The composite nanofibrous scaffolds were subjected to detailed analysis. Morphological investigations revealed that the prepared nanofibers have uniform morphology and the average fiber diameters of aligned and random scaffolds were 135.5 and 290 nm, respectively. The obtained scaffolds have a porous structure with porosity of 88 and 76% for random and aligned nanofibers, respectively. Furthermore, FTIR analysis demonstrated that there were strong intramolecular interactions between the molecules of PVA/PCL/nHA. On the other hand, mechanical characterizations show that aligning the nanofibers, could significantly improve the rigidity of the resultant biocomposite nanofibrous scaffolds.
Abstract: The study explored varied types of human smiles and
extracted most of the key factors affecting the smiles. These key
factors then were converted into a set of control points which could
serve to satisfy the needs for creation of facial expression for 3D
animators and be further applied to the face simulation for robots in the
future. First, hundreds of human smile pictures were collected and
analyzed to identify the key factors for face expression. Then, the
factors were converted into a set of control points and sizing
parameters calculated proportionally. Finally, two different faces
were constructed for validating the parameters via the process of
simulating smiles of the same type as the original one.
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.
Abstract: The Integrated Performance Modelling Environment
(IPME) is a powerful simulation engine for task simulation and
performance analysis. However, it has no high level cognition such
as memory and reasoning for complex simulation. This article
introduces a knowledge representation and reasoning scheme that can
accommodate uncertainty in simulations of military personnel with
IPME. This approach demonstrates how advanced reasoning models
that support similarity-based associative process, rule-based abstract
process, multiple reasoning methods and real-time interaction can be
integrated with conventional task network modelling to provide
greater functionality and flexibility when modelling operator
performance.
Abstract: Routing places an important role in determining the
quality of service in wireless networks. The routing methods adopted
in wireless networks have many drawbacks. This paper aims to
review the current routing methods used in wireless networks. This
paper proposes an innovative solution to overcome the problems in
routing. This solution is aimed at improving the Quality of Service.
This solution is different from others as it involves the resuage of the
part of the virtual circuits. This improvement in quality of service is
important especially in propagation of multimedia applications like
video, animations etc. So it is the dire need to propose a new solution
to improve the quality of service in ATM wireless networks for
multimedia applications especially during this era of multimedia
based applications.
Abstract: Modeling and simulation of fixed bed three-phase
catalytic reactors are considered for wet air catalytic oxidation of
phenol to perform a comparative numerical analysis between tricklebed
and packed-bubble column reactors. The modeling involves
material balances both for the catalyst particle as well as for different
fluid phases. Catalyst deactivation is also considered in a transient
reactor model to investigate the effects of various parameters
including reactor temperature on catalyst deactivation. The
simulation results indicated that packed-bubble columns were
slightly superior in performance than trickle beds. It was also found
that reaction temperature was the most effective parameter in catalyst
deactivation.
Abstract: A novel typical day prediction model have been built and validated by the measured data of a grid-connected solar photovoltaic (PV) system in Macau. Unlike conventional statistical method used by previous study on PV systems which get results by averaging nearby continuous points, the present typical day statistical method obtain the value at every minute in a typical day by averaging discontinuous points at the same minute in different days. This typical day statistical method based on discontinuous point averaging makes it possible for us to obtain the Gaussian shape dynamical distributions for solar irradiance and output power in a yearly or monthly typical day. Based on the yearly typical day statistical analysis results, the maximum possible accumulated output energy in a year with on site climate conditions and the corresponding optimal PV system running time are obtained. Periodic Gaussian shape prediction models for solar irradiance, output energy and system energy efficiency have been built and their coefficients have been determined based on the yearly, maximum and minimum monthly typical day Gaussian distribution parameters, which are obtained from iterations for minimum Root Mean Squared Deviation (RMSD). With the present model, the dynamical effects due to time difference in a day are kept and the day to day uncertainty due to weather changing are smoothed but still included. The periodic Gaussian shape correlations for solar irradiance, output power and system energy efficiency have been compared favorably with data of the PV system in Macau and proved to be an improvement than previous models.
Abstract: Prostate cancer is one of the most frequent cancers in men and is a major cause of mortality in the most of countries. In many diagnostic and treatment procedures for prostate disease accurate detection of prostate boundaries in transrectal ultrasound (TRUS) images is required. This is a challenging and difficult task due to weak prostate boundaries, speckle noise and the short range of gray levels. In this paper a novel method for automatic prostate segmentation in TRUS images is presented. This method involves preprocessing (edge preserving noise reduction and smoothing) and prostate segmentation. The speckle reduction has been achieved by using stick filter and top-hat transform has been implemented for smoothing. A feed forward neural network and local binary pattern together have been use to find a point inside prostate object. Finally the boundary of prostate is extracted by the inside point and an active contour algorithm. A numbers of experiments are conducted to validate this method and results showed that this new algorithm extracted the prostate boundary with MSE less than 4.6% relative to boundary provided manually by physicians.
Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: The objective of the present communication is to
develop new genuine exponentiated mean codeword lengths and to
study deeply the problem of correspondence between well known
measures of entropy and mean codeword lengths. With the help of
some standard measures of entropy, we have illustrated such a
correspondence. In literature, we usually come across many
inequalities which are frequently used in information theory.
Keeping this idea in mind, we have developed such inequalities via
coding theory approach.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.
Abstract: With the exponential progress of technological
development comes a strong sense that events are moving too quickly
for our schools and that teachers may be losing control of them in the
process. This paper examines the impact of e-learning and e-teaching
in universities, from both the student and teacher perspective. In
particular, it is shown that e-teachers should focus not only on the
technical capacities and functions of IT materials and activities, but
must attempt to more fully understand how their e-learners perceive
the learning environment. From the e-learner perspective, this paper
indicates that simply having IT tools available does not automatically
translate into all students becoming effective learners. More
evidence-based evaluative research is needed to allow e-learning and
e-teaching to reach full potential.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.
Abstract: The peculiarities of the nanoscale structure-phase
states formed after electroexplosive carburizing and subsequent
electron-beam treatment of technically pure titanium surface in different regimes are established by methods of transmission electron
diffraction microscopy and physical mechanisms are discussed. Electroexplosive carburizing leads to surface layer formation
(40 m thickness) with increased (in 3.5 times) microhardness. It consists of β-titanium, graphite (monocrystals 100-150 nm,
polycrystals 5-10 nm, amorphous particles 3-5nm), TiC (5-10 nm), β-Ti02 (2-20nm). After electron-beam treatment additionally increasing the microhardness the surface layer consists of TiC.
Abstract: System-level design based on high-level abstractions
is becoming increasingly important in hardware and embedded
system design. This paper analyzes meta-design techniques oriented
at developing meta-programs and meta-models for well-understood
domains. Meta-design techniques include meta-programming and
meta-modeling. At the programming level of design process, metadesign
means developing generic components that are usable in a
wider context of application than original domain components. At the
modeling level, meta-design means developing design patterns that
describe general solutions to the common recurring design problems,
and meta-models that describe the relationship between different
types of design models and abstractions. The paper describes and
evaluates the implementation of meta-design in hardware design
domain using object-oriented and meta-programming techniques.
The presented ideas are illustrated with a case study.
Abstract: The counting and analysis of blood cells allows the
evaluation and diagnosis of a vast number of diseases. In particular,
the analysis of white blood cells (WBCs) is a topic of great interest to
hematologists. Nowadays the morphological analysis of blood cells is
performed manually by skilled operators. This involves numerous
drawbacks, such as slowness of the analysis and a nonstandard
accuracy, dependent on the operator skills. In literature there are only
few examples of automated systems in order to analyze the white
blood cells, most of which only partial. This paper presents a
complete and fully automatic method for white blood cells
identification from microscopic images. The proposed method firstly
individuates white blood cells from which, subsequently, nucleus and
cytoplasm are extracted. The whole work has been developed using
MATLAB environment, in particular the Image Processing Toolbox.