Abstract: this paper presents a novel scheme which is capable of reducing the error rate and improves the transmission performance in the asynchronous cooperative MIMO systems. A case study of image transmission is applied to prove the efficient of scheme. The linear dispersion structure is employed to accommodate the cooperative wireless communication network in the dynamic topology of structure, as well as to achieve higher throughput than conventional space–time codes based on orthogonal designs. The LDPC encoder without girth-4 and the STBC encoder with guard intervals are respectively introduced. The experiment results show that the combined coder of LDPC-STBC with guard intervals can be the good error correcting coders and BER performance in the asynchronous cooperative communication. In the case study of image transmission, the results show that in the transmission process, the image quality which is obtained by applied combined scheme is much better than it which is not applied the scheme in the asynchronous cooperative MIMO systems.
Abstract: WiMAX is defined as Worldwide Interoperability for
Microwave Access by the WiMAX Forum, formed in June 2001 to
promote conformance and interoperability of the IEEE 802.16
standard, officially known as WirelessMAN. The attractive features
of WiMAX technology are very high throughput and Broadband
Wireless Access over a long distance. A detailed simulation
environment is demonstrated with the UGS, nrtPS and ertPS service
classes for throughput, delay and packet delivery ratio for a mixed
environment of fixed and mobile WiMAX. A simple mobility aspect
is considered for the mobile WiMAX and the PMP mode of
transmission is considered in TDD mode. The Network Simulator 2
(NS-2) is the tool which is used to simulate the WiMAX network
scenario. A simple Priority Scheduler and Weighted Round Robin
Schedulers are the WiMAX schedulers used in the research work
Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.
Abstract: The “PYRAMIDS" Block Cipher is a symmetric encryption algorithm of a 64, 128, 256-bit length, that accepts a variable key length of 128, 192, 256 bits. The algorithm is an iterated cipher consisting of repeated applications of a simple round transformation with different operations and different sequence in each round. The algorithm was previously software implemented in Cµ code. In this paper, a hardware implementation of the algorithm, using Field Programmable Gate Arrays (FPGA), is presented. In this work, we discuss the algorithm, the implemented micro-architecture, and the simulation and implementation results. Moreover, we present a detailed comparison with other implemented standard algorithms. In addition, we include the floor plan as well as the circuit diagrams of the various micro-architecture modules.
Abstract: A hybrid learning automata-genetic algorithm (HLGA) is proposed to solve QoS routing optimization problem of next generation networks. The algorithm complements the advantages of the learning Automato Algorithm(LA) and Genetic Algorithm(GA). It firstly uses the good global search capability of LA to generate initial population needed by GA, then it uses GA to improve the Quality of Service(QoS) and acquiring the optimization tree through new algorithms for crossover and mutation operators which are an NP-Complete problem. In the proposed algorithm, the connectivity matrix of edges is used for genotype representation. Some novel heuristics are also proposed for mutation, crossover, and creation of random individuals. We evaluate the performance and efficiency of the proposed HLGA-based algorithm in comparison with other existing heuristic and GA-based algorithms by the result of simulation. Simulation results demonstrate that this paper proposed algorithm not only has the fast calculating speed and high accuracy but also can improve the efficiency in Next Generation Networks QoS routing. The proposed algorithm has overcome all of the previous algorithms in the literature.
Abstract: In this paper, we deal with the Steiner tree problem
(STP) on a graph in which a fuzzy number, instead of a real number,
is assigned to each edge. We propose a modification of the shortest
paths approximation based on the fuzzy shortest paths (FSP)
evaluations. Since a fuzzy min operation using the extension
principle leads to nondominated solutions, we propose another
approach to solving the FSP using Cheng's centroid point fuzzy
ranking method.
Abstract: The existence of many biological systems,
especially human societies, is based on cooperative behavior
[1, 2]. If natural selection favors selfish individuals, then what
mechanism is at work that we see so many cooperative
behaviors? One answer is the effect of network structure. On a
graph, cooperators can evolve by forming network bunches
[2, 3, 4]. In a research, Ohtsuki et al used the idea of iterated
prisoners- dilemma on a graph to model an evolutionary
game. They showed that the average number of neighbors
plays an important role in determining whether cooperation is
the ESS of the system or not [3]. In this paper, we are going to
study the dynamics of evolution of cooperation in a social
network. We show that during evolution, the ratio of
cooperators among individuals with fewer neighbors to
cooperators among other individuals is greater than unity. The
extent to which the fitness function depends on the payoff of
the game determines this ratio.
Abstract: Water Sensitive Urban Design (WSUD) features are
increasingly used to treat and manage polluted stormwater runoff in urbanised areas. It is important to monitor and evaluate the effectiveness of the infrastructure in achieving their intended performance targets after constructing and operating these features
overtime. The paper presents the various methods of analysis used to
assess the effectiveness of the in-situ WSUD features, such as: onsite visual inspections during operational and non operational periods, maintenance audits and periodic water quality testing. The results will contribute to a better understanding of the operational and
maintenance needs of in-situ WSUD features and assist in providing recommendations to better manage life cycle performance.
Abstract: This paper proposes a Wavelength Division
Multiplexing (WDM) technology based Storage Area Network
(SAN) for all type of Disaster recovery operation. It considers
recovery when all paths failure in the network as well as the main
SAN site failure also the all backup sites failure by the effect of
natural disasters such as earthquakes, fires and floods, power outage,
and terrorist attacks, as initially SAN were designed to work within
distance limited environments[2]. Paper also presents a NEW PATH
algorithm when path failure occurs. The simulation result and
analysis is presented for the proposed architecture with performance
consideration.
Abstract: The optimal operation of proton exchange membrane fuel cell (PEMFC) requires good water management which is presented under two forms vapor and liquid. Moreover, fuel cells have to reach higher output require integration of some accessories which need electrical power. In order to analyze fuel cells operation and different species transport phenomena a biphasic mathematical model is presented by governing equations set. The numerical solution of these conservation equations is calculated by Matlab program. A multi-criteria optimization with weighting between two opposite objectives is used to determine the compromise solutions between maximum output and minimal stack size. The obtained results are in good agreement with available literature data.
Abstract: The Malaysia Highway Authority (MHA) was
established by the Government in 1980 for the purpose of designing,
constructing and maintaining toll highways in Malaysia that include
the North-South Expressway and the Penang Bridge, which were
procured using the publicly-funded traditional procurement. However
following a recession in the mid 80-s, the operations of these tolledhighways
had been privatized to ensure that their operational services
continue through private financing as a result of long-term
concession agreement concurred between the Malaysian Government
and private operators. The change in the contract strategy for
highway projects in Malaysia would have a great tendency to dictate
a significant risk exposure towards the key parties involved,
particularly the Malaysian Government as project principal, unless
operational risks are clearly identified and managed via appropriate
mitigation measures prior to a contract signing.
This research identifies potential operational risks that have a
possibility to occur in highway projects in Malaysia from the
perspective of public sector clients. Since this research focuses on the
operational risks for highway projects in Malaysia, the initial results
acquired from literature review on the operational risks of highway
projects in some Asian countries are then justified by a number of
key individuals from the MHA through interviews. As a result,
among key operational risks that have possibility to occur in the
highway projects in Malaysia include initial toll-tariff decided by the
Government, traffic congestion, change of road network and overloaded
freight transportation, which could cause damage to the road
surface and hence affecting the operation of a particular highway.
Abstract: Oxide scale thickness measurements are used in assessing the life of different components operating at high temperature environment. Such measurements provide an approximation for the temperature inside components such as reheater and superheater tubes. A number of failures were encountered in one of the boilers in one of Kuwaiti power plants. These failure were mainly in the first row of the primary super heater tubes, therefore, the specialized engineer decide to replace them during the annual shutdown. As a tool for failure analysis, oxide scale thickness measurement were used to investigate the temperature distribution in these tubes. In this paper, the oxide scale thickness of these tubes were measured and used for analysis. The measurements provide an illustration of the distribution of heat transfer of the primary superheater tubes in the boiler system. Remarks and analysis about the design of the boiler are also provided.
Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.
Abstract: In this paper, a near lossless image coding scheme
based on Orthogonal Polynomials Transform (OPT) has been
presented. The polynomial operators and polynomials basis operators
are obtained from set of orthogonal polynomials functions for the
proposed transform coding. The image is partitioned into a number of
distinct square blocks and the proposed transform coding is applied to
each of these individually. After applying the proposed transform
coding, the transformed coefficients are rearranged into a sub-band
structure. The Embedded Zerotree (EZ) coding algorithm is then
employed to quantize the coefficients. The proposed transform is
implemented for various block sizes and the performance is
compared with existing Discrete Cosine Transform (DCT) transform
coding scheme.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: Research in e-Business has been growing
tremendously covering all related aspects such as adoption issues, e-
Business models, strategies, etc. This research aims to explore the
potential of adopting e-Business for a micro size business operating
from home called home-based businesses (HBBs). In Malaysia, the
HBB industry started many years ago and were mostly monopolized
by women or housewives managed as a part-time job to support their
family economy. Today, things have changed. The availability of the
Internet technology and the emergence of e-Business concept
promote the evolution of HBBs, which have been adopted as another
alternative as a professional career for women without neglecting
their family needs especially the children. Although this study is
confined to a limited sample size and within geographical biasness,
the findings show that it concurs with previous large scale studies. In
this study, both qualitative and quantitative methods were used and
data were gathered using triangulation methods via interview, direct
observation, document analysis and survey questionnaires. This paper
discusses the literature review, research methods and findings
pertaining to e-Business adoption factors that influence the HBBs in
Malaysia.
Abstract: Transnational corporations (TNCs) are playing a major role in global R&D, not only through activities in their home countries but also increasingly abroad. However, the process of R&D offshoring is not yet discussed thoroughly. Based on in-depth case study on Agilent China Communications Operation, this paper presents a stage model for theorizing the R&D offshoring process. This stage model outlines 5 maturity levels of organization and the offshoring process: Subsidiary team, Mirror team, Independent team, Mirror sector and the Independent sector (from software engineering point of view, it is similar to the local team's capability level of maturity model). Moreover, the paper gives a detailed discussion on the relevant characteristics, as well as the ability/responsibility of transfer, priorities and the corresponding organization structure. It also gives the characteristics and key points of different level-s R&D offshoring implementation using actual team practice.
Abstract: Many contemporary telemedical applications rely on
regular consultations over the phone or video conferencing which
consumes valuable resources such as the time of the doctors. Some
applications or treatments allow automated diagnostics on the patient
side which only notifies the doctors in case a significant worsening
of patient’s condition is measured.
Such programs can save valuable resources but an important
implementation issue is how to ensure effective and cheap diagnostics
on the patient side. First, specific diagnostic devices on patient side
are expensive and second, they need to be user-˜friendly to encourage
patient’s cooperation and reduce errors in usage which may cause
noise in diagnostic data.
This article proposes the use of modern smartphones and various
build-in or attachable sensors as universal diagnostic devices applicable
in a wider range of telemedical programs and demonstrates their
application on a case-study – a program for schizophrenic relapse
prevention.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.
Abstract: For professions of high risk industries, simulation training has always been thought in terms of high degree of fidelity regarding the real operational situation. Due to the recent progress, this way of training is changing, modifying the human-computer and software interactions: the interactions between trainees during simulation training session tend to become virtual, transforming the social-based embodiness (the way subjects integrate social skills for interpersonal relationship with co-workers). On the basis of the analysis of eight different profession trainings, a categorization of interactions has help to produce an analytical tool, the social interactions table. This tool may be very valuable to point out the changes of social interactions when the training sessions are skipping from a high fidelity simulator to a virtual simulator. In this case, it helps the designers of professional training to analyze and to assess the consequences of the potential lack the social-based embodiness.