Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: In the recent past, there has been an increasing interest
in applying evolutionary methods to Knowledge Discovery in
Databases (KDD) and a number of successful applications of Genetic
Algorithms (GA) and Genetic Programming (GP) to KDD have been
demonstrated. The most predominant representation of the
discovered knowledge is the standard Production Rules (PRs) in the
form If P Then D. The PRs, however, are unable to handle
exceptions and do not exhibit variable precision. The Censored
Production Rules (CPRs), an extension of PRs, were proposed by
Michalski & Winston that exhibit variable precision and supports an
efficient mechanism for handling exceptions. A CPR is an
augmented production rule of the form:
If P Then D Unless C, where C (Censor) is an exception to the rule.
Such rules are employed in situations, in which the conditional
statement 'If P Then D' holds frequently and the assertion C holds
rarely. By using a rule of this type we are free to ignore the exception
conditions, when the resources needed to establish its presence are
tight or there is simply no information available as to whether it
holds or not. Thus, the 'If P Then D' part of the CPR expresses
important information, while the Unless C part acts only as a switch
and changes the polarity of D to ~D.
This paper presents a classification algorithm based on evolutionary
approach that discovers comprehensible rules with exceptions in the
form of CPRs.
The proposed approach has flexible chromosome encoding, where
each chromosome corresponds to a CPR. Appropriate genetic
operators are suggested and a fitness function is proposed that
incorporates the basic constraints on CPRs. Experimental results are
presented to demonstrate the performance of the proposed algorithm.
Abstract: Open Agent System platform based on High Level
Architecture is firstly proposed to support the application involving
heterogeneous agents. The basic idea is to develop different wrappers
for different agent systems, which are wrapped as federates to join a
federation. The platform is based on High Level Architecture and the
advantages for this open standard are naturally inherited, such as
system interoperability and reuse. Especially, the federal architecture
allows different federates to be heterogeneous so as to support the
integration of different agent systems. Furthermore, both implicit
communication and explicit communication between agents can be
supported. Then, as the wrapper RTI_JADE an example, the
components are discussed. Finally, the performance of RTI_JADE is
analyzed. The results show that RTI_JADE works very efficiently.
Abstract: The perfect operation of common Active Filters is depended on accuracy of identification system distortion. Also, using a suitable method in current injection and reactive power compensation, leads to increased filter performance. Due to this fact, this paper presents a method based on predictive current control theory in shunt active filter applications. The harmonics of the load current is identified by using o–d–q reference frame on load current and eliminating the DC part of d–q components. Then, the rest of these components deliver to predictive current controller as a Threephase reference current by using Park inverse transformation. System is modeled in discreet time domain. The proposed method has been tested using MATLAB model for a nonlinear load (with Total Harmonic Distortion=20%). The simulation results indicate that the proposed filter leads to flowing a sinusoidal current (THD=0.15%) through the source. In addition, the results show that the filter tracks the reference current accurately.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Rotation or tilt present in an image capture by digital
means can be detected and corrected using Artificial Neural Network
(ANN) for application with a Face Recognition System (FRS). Principal
Component Analysis (PCA) features of faces at different angles
are used to train an ANN which detects the rotation for an input image
and corrected using a set of operations implemented using another
system based on ANN. The work also deals with the recognition
of human faces with features from the foreheads, eyes, nose and
mouths as decision support entities of the system configured using
a Generalized Feed Forward Artificial Neural Network (GFFANN).
These features are combined to provide a reinforced decision for
verification of a person-s identity despite illumination variations. The
complete system performing facial image rotation detection, correction
and recognition using re-enforced decision support provides a
success rate in the higher 90s.
Abstract: Human amniotic membrane (HAM) is a useful
biological material for the reconstruction of damaged ocular surface.
The processing and preservation of HAM is critical to prevent the
patients undergoing amniotic membrane transplant (AMT) from cross
infections. For HAM preparation human placenta is obtained after an
elective cesarean delivery. Before collection, the donor is screened
for seronegativity of HCV, Hbs Ag, HIV and Syphilis. After
collection, placenta is washed in balanced salt solution (BSS) in
sterile environment. Amniotic membrane is then separated from the
placenta as well as chorion while keeping the preparation in BSS.
Scrapping of HAM is then carried out manually until all the debris is
removed and clear transparent membrane is acquired. Nitrocellulose
membrane filters are then placed on the stromal side of HAM, cut
around the edges with little membrane folded towards other side
making it easy to separate during surgery. HAM is finally stored in
solution of glycerine and Dulbecco-s Modified Eagle Medium
(DMEM) in 1:1 ratio containing antibiotics. The capped borosil vials
containing HAM are kept at -80°C until use. This vial is thawed to
room temperature and opened under sterile operation theatre
conditions at the time of surgery.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Recently research on human wayfinding has focused
mainly on mental representations rather than processes of
wayfinding. The objective of this paper is to demonstrate the
rationality behind applying multi-agent simulation paradigm to the
modeling of rescuer team wayfinding in order to develop
computational theory of perceptual wayfinding in crisis situations
using image schemata and affordances, which explains how people
find a specific destination in an unfamiliar building such as a
hospital. The hypothesis of this paper is that successful navigation is
possible if the agents are able to make the correct decision through
well-defined cues in critical cases, so the design of the building
signage is evaluated through the multi-agent-based simulation. In
addition, a special case of wayfinding in a building, finding one-s
way through three hospitals, is used to demonstrate the model.
Thereby, total rescue time for rescue operation during building fire is
computed. This paper discuses the computed rescue time for various
signage localization and provides experimental result for
optimization of building signage design. Therefore the most
appropriate signage design resulted in the shortest total rescue time in
various situations.
Abstract: In this paper, a design methodology to implement low-power and high-speed 2nd order recursive digital Infinite Impulse Response (IIR) filter has been proposed. Since IIR filters suffer from a large number of constant multiplications, the proposed method replaces the constant multiplications by using addition/subtraction and shift operations. The proposed new 6T adder cell is used as the Carry-Save Adder (CSA) to implement addition/subtraction operations in the design of recursive section IIR filter to reduce the propagation delay. Furthermore, high-level algorithms designed for the optimization of the number of CSA blocks are used to reduce the complexity of the IIR filter. The DSCH3 tool is used to generate the schematic of the proposed 6T CSA based shift-adds architecture design and it is analyzed by using Microwind CAD tool to synthesize low-complexity and high-speed IIR filters. The proposed design outperforms in terms of power, propagation delay, area and throughput when compared with MUX-12T, MCIT-7T based CSA adder filter design. It is observed from the experimental results that the proposed 6T based design method can find better IIR filter designs in terms of power and delay than those obtained by using efficient general multipliers.
Abstract: The objective of this study was to investigate hydrogen production from alcohol wastewater by anaerobic sequencing batch reactor (ASBR) under thermophillic operation. The ASBR unit used in this study had a liquid holding volume of 4 L and was operated at 6 cycles per day. The seed sludge taken from an upflow anaerobic sludge blanket unit treating the same wastewater was boiled at 95 °C for 15 min before being fed to the ASBR unit. The ASBR system was operated at different COD loading rates at a thermophillic temperature (55 °C), and controlled pH of 5.5. When the system was operated under optimum conditions (providing maximum hydrogen production performance) at a feed COD of 60 000 mg/l, and a COD loading rate of 68 kg/m3 d, the produced gas contained 43 % H2 content in the produced gas. Moreover, the hydrogen yield and the specific hydrogen production rate (SHPR) were 130 ml H2/g COD removed and 2100 ml H2/l d, respectively.
Abstract: The key to the continued success of ANN depends, considerably,
on the use of hybrid structures implemented on cooperative
frame-works. Hybrid architectures provide the ability to the ANN
to validate heterogeneous learning paradigms. This work describes
the implementation of a set of Distributed and Hybrid ANN models
for Character Recognition applied to Anglo-Assamese scripts. The
objective is to describe the effectiveness of Hybrid ANN setups as
innovative means of neural learning for an application like multilingual
handwritten character and numeral recognition.
Abstract: Fundamental motivation of this paper is how gaze estimation can be utilized effectively regarding an application to games. In games, precise estimation is not always important in aiming targets but an ability to move a cursor to an aiming target accurately is also significant. Incidentally, from a game producing point of view, a separate expression of a head movement and gaze movement sometimes becomes advantageous to expressing sense of presence. A case that panning a background image associated with a head movement and moving a cursor according to gaze movement can be a representative example. On the other hand, widely used technique of POG estimation is based on a relative position between a center of corneal reflection of infrared light sources and a center of pupil. However, a calculation of a center of pupil requires relatively complicated image processing, and therefore, a calculation delay is a concern, since to minimize a delay of inputting data is one of the most significant requirements in games. In this paper, a method to estimate a head movement by only using corneal reflections of two infrared light sources in different locations is proposed. Furthermore, a method to control a cursor using gaze movement as well as a head movement is proposed. By using game-like-applications, proposed methods are evaluated and, as a result, a similar performance to conventional methods is confirmed and an aiming control with lower computation power and stressless intuitive operation is obtained.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.
Abstract: A new method of adaptation in a partially integrated learning environment that includes electronic textbook (ET) and integrated tutoring system (ITS) is described. The algorithm of adaptation is described in detail. It includes: establishment of Interconnections of operations and concepts; estimate of the concept mastering level (for all concepts); estimate of student-s non-mastering level on the current learning step of information on each page of ET; creation of a rank-order list of links to the e-manual pages containing information that require repeated work.