Abstract: The purpose of the present work was to study the
production and process parameters optimization for the synthesis of
cellulase from Trichoderma viride in solid state fermentation (SSF)
using an agricultural wheat straw as substrates; as fungal conversion
of lignocellulosic biomass for cellulase production is one among the
major increasing demand for various biotechnological applications.
An optimization of process parameters is a necessary step to get
higher yield of product. Several kinetic parameters like pretreatment,
extraction solvent, substrate concentration, initial moisture content,
pH, incubation temperature and inoculum size were optimized for
enhanced production of third most demanded industrially important
cellulase. The maximum cellulase enzyme activity 398.10±2.43
μM/mL/min was achieved when proximally analyzed lignocellulosic
substrate wheat straw inocubated at 2% HCl as pretreatment tool
along with distilled water as extraction solvent, 3% substrate
concentration 40% moisture content with optimum pH 5.5 at 45°C
incubation temperature and 10% inoculum size.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Lately management strategy that put Industrial Design (ID) in its core is recognized more important, as technology and price alone cannot differentiate a product. The needs to shorten the time to develop a product also shorten the development period of ID, and it necessitates the ID process management. This research analyzes the status of integration process of ID and Engineering Design (ED) of office equipment that requires the collaboration of ID and ED to clarify the issues for the efficiency of the development and to propose solutions.
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: In the context of large volume Big Divisor (nearly)
SLagy D3/D7 μ-Split SUSY [1], after an explicit identification
of first generation of SM leptons and quarks with fermionic superpartners
of four Wilson line moduli, we discuss the identification of
gravitino as a potential dark matter candidate by explicitly calculating
the decay life times of gravitino (LSP) to be greater than age of
universe and lifetimes of decays of the co-NLSPs (the first generation
squark/slepton and a neutralino) to the LSP (the gravitino) to be
very small to respect BBN constraints. Interested in non-thermal
production mechanism of gravitino, we evaluate the relic abundance
of gravitino LSP in terms of that of the co-NLSP-s by evaluating
their (co-)annihilation cross sections and hence show that the former
satisfies the requirement for a potential Dark Matter candidate. We
also show that it is possible to obtain a 125 GeV light Higgs in our
setup.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: This paper introduces the effective speckle reduction of
synthetic aperture radar (SAR) images using inner product spaces in
undecimated wavelet domain. There are two major areas in projection
onto span algorithm where improvement can be made. First is the use
of undecimated wavelet transformation instead of discrete wavelet
transformation. And second area is the use of smoothing filter namely
directional smoothing filter which is an additional step. Proposed
method does not need any noise estimation and thresholding
technique. More over proposed method gives good results on both
single polarimetric and fully polarimetric SAR images.
Abstract: The availability of broadband internet and increased
access to computers has been instrumental in the rise of internet
literacy in Malaysia. This development has led to the adoption of
online shopping by many Malaysians. On another note, the
Government has supported the development and production of local
herbal products. This has resulted in an increase in the production and
diversity of products by SMEs. The purpose of this study is to
evaluate the influence of the Malaysian demographic factors and
selected attitudinal characteristics in relation to the online purchasing
of herbal products. In total, 1054 internet users were interviewed
online and Chi-square analysis was used to determine the relationship
between demographic variables and different aspects of online
shopping for herbal products. The overall results show that the
demographic variables such as age, gender, education level, income
and ethnicity were significant when considering the online shopping
antecedents of trust, quality of herbal products, perceived risks and
perceived benefits.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: carrot is one of the important root vegetable crops,
and it is highly nutritious as it contains appreciable amount of
vitamins, minerals and β-carotene. The major objective of current
research was to evaluate the chemical composition of carrot variety
'Nante' hybrids in general and to select the best samples for fresh-cut
salad production. The research was accomplished on fresh in Latvia
cultivated carrots harvested in Zemgale region in the first part of
October, 2011 and immediately used for experiments. Late-bearing
variety 'Nante' hybrid carrots were used for analysis:
'Nante/Berlikum', 'Nante/Maestro', 'Nante/Forto', 'Nante/Bolero'
and 'Nante/Champion'. The quality parameters as moisture, soluble
solid, firmness, b-carotene, carotenoid, color, polyphenols, total
phenolic compounds and total antioxidant capacity were analyzed
using standard methods. For fresh-cut salad production as more
applicable could be recommended hybrids 'Nante/Forto' and
'Nante/Berlikum' - mainly because it-s higher nutritive value, as
higher total phenolic compounds, polyphenols and pronounced
antioxidant capacity.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: This research aims to study value-creation process of
producing monk-s bowls, Thai traditional handicrafts, which is facing problems in adapting to the changing society. It also aims to identify
problems and obstacles to value creation. This research is based on a case study of monk-s bowl manufactures from Ban-Baat Village,
Bangkok. The conceptual framework is based on the model of value
chain to analyze the process.
The research methodology is qualitative. This research found that the value-creation process of monk-s bowls consists of eight
activities contributing to adding value to the products and increasing
profits to the producers in return. Five major problems and obstacles
are found.
The research suggests that these problems and obstacles limit the manufacturers- potential for creating more valued product and lead to business stagnation. These problems should be addressed and solved with collaboration among the government, the private sector and the
manufacturers.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: One of the most important problems in production planning of flexible manufacturing system (FMS) is machine tool selection and operation allocation problem that directly influences the production costs and times .In this paper minimizing machining cost, set-up cost and material handling cost as a multi-objective problem in flexible manufacturing systems environment are considered. We present a 0-1 integer linear programming model for the multiobjective machine tool selection and operation allocation problem and due to the large scale nature of the problem, solving the problem to obtain optimal solution in a reasonable time is infeasible, Paretoant colony optimization (P-ACO) approach for solving the multiobjective problem in reasonable time is developed. Experimental results indicate effectiveness of the proposed algorithm for solving the problem.
Abstract: In this study, a mathematical model was proposed and
the accuracy of this model was assessed to predict the growth of
Pseudomonas aeruginosa and rhamnolipid production under nitrogen
limiting (sodium nitrate) fed-batch fermentation. All of the
parameters used in this model were achieved individually without
using any data from the literature.
The overall growth kinetic of the strain was evaluated using a
dual-parallel substrate Monod equation which was described by
several batch experimental data. Fed-batch data under different
glycerol (as the sole carbon source, C/N=10) concentrations and feed
flow rates were used to describe the proposed fed-batch model and
other parameters. In order to verify the accuracy of the proposed
model several verification experiments were performed in a vast
range of initial glycerol concentrations. While the results showed an
acceptable prediction for rhamnolipid production (less than 10%
error), in case of biomass prediction the errors were less than 23%. It
was also found that the rhamnolipid production by P. aeruginosa was
more sensitive at low glycerol concentrations.
Based on the findings of this work, it was concluded that the
proposed model could effectively be employed for rhamnolipid
production by this strain under fed-batch fermentation on up to 80 g l-
1 glycerol.
Abstract: In this paper, we show that C*-tensor product of an arbitrary C*-algebra A, (not unital necessary) and C*-algebra B without ground state, have no approximately inner strongly continuous one-parameter group of *-automorphisms.
Abstract: Surgical site infections (SSIs) are the most common
nosocomial infection in surgical patients resulting in significant
increases in postoperative morbidity and mortality. The commonly
causative bacteria developed resistance to virtually all antibiotics
available. The aim of this study was to isolation and identification the
most common bacteria that cause SSIs in Medical Research Institute,
and to compare their sensitivity to selected group of antibiotics and
natural products (garlic, oregano, olive, and Nigella sativa oils). The
isolated pathogens collected from infected surgical wounds were
identified, and their sensitivities to the antibiotics commonly
available for clinical use, and also to the different concentrations of
the used natural products were investigated. The results indicate to
the potential therapeutic effect of the tested natural products in
treatment of surgical wound infections.
Abstract: The aim of the study was to determine how different
ripening processes (traditional vs. industrial) influenced the
proteolysis in traditional Serbian dry-fermented sausage Petrovská
klobása. The obtained results indicated more intensive pH decline
(0.7 units after 9 days) in industrially ripened products (I), what had a
positive impact on drying process and proteolytic changes in these
samples. Thus, moisture content in I sausages was lower at each
sampling time, amounting 24.7% at the end of production period
(90 days). Likewise, the process of proteolysis was more pronounced
in I samples, resulting in higher contents of non-protein nitrogen
(NPN) and free amino acids nitrogen (FAAN), as well as in faster
and more intensive degradation of myosin (≈220 kDa), actin (≈45
kDa) and other polypeptides during processing. Consequently, the
appearance and accumulation of several protein fragments were
registered.