Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Computer education is referred to as the knowledge
and ability to use computers and related technology efficiently, with a
range of skills covering levels from basic use to advance. Computer
continues to make an ever-increasing impact on all aspect of human
endeavours such as education. With numerous benefits of computer
education, what are the insights of students on computer education?
This study investigated the perception of senior secondary school
students on computer education in Federal Capital Territory (FCT),
Abuja, Nigeria. A sample of 7500 senior secondary schools students
was involved in the study, one hundred (100) private and fifty (50)
public schools within FCT. They were selected by using simple
random sampling technique. A questionnaire [PSSSCEQ] was
developed and validated through expert judgement and reliability coefficient
of 0.84 was obtained. It was used to gather relevant data on
computer education. Findings confirmed that the students in the FCT
had positive perception on computer education. Some factors were
identified that affect students’ perception on computer education. The
null hypotheses were tested using t-test and ANOVA statistical
analyses at 0.05 level of significance. Based on these findings, some
recommendations were made which include competent teachers
should be employed into all secondary schools. This will help
students to acquire relevant knowledge in computer education,
technological supports should be provided to all secondary schools;
this will help the users (students) to solve specific problems in
computer education and financial supports should be provided to
procure computer facilities that will enhance the teaching and the
learning of computer education.
Abstract: Web Usage Mining is the application of data mining
techniques to find usage patterns from web log data, so as to grasp
required patterns and serve the requirements of Web-based
applications. User’s expertise on the internet may be improved by
minimizing user’s web access latency. This may be done by
predicting the future search page earlier and the same may be prefetched
and cached. Therefore, to enhance the standard of web
services, it is needed topic to research the user web navigation
behavior. Analysis of user’s web navigation behavior is achieved
through modeling web navigation history. We propose this technique
which cluster’s the user sessions, based on the K-medoids technique.
Abstract: Dengue is a mosquito-borne viral disease endemic in
many countries in the tropics and sub-tropics. The state of Punjab in
India shows cyclical and seasonal variation in dengue cases. The
Case Fatality Rate of Dengue has ranged from 0.6 to 1.0 in the past
years. The department has initiated review of the cases that have died
due to dengue in order to know the exact cause of the death in a case
of dengue. The study has been undertaken to know the other
associated co-morbidities and factors causing death in a case of
dengue. The study used the predesigned proforma on which the
records (medical and Lab) were recorded and reviewed by the expert
committee of the doctors. This study has revealed that cases of
dengue having co-morbidities have longer stay in hospital. Fluid
overload and co-morbidities have been found as major factors leading
to death, however, in a confirmed case of dengue hepatorenal
shutdown was found to be major cause of mortality. The data
obtained will help in sensitizing the treating physicians in order to
decrease the mortality due to dengue in future.
Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: Distance learning systems offer useful methods of
learning and usually contain a final course test or another form of
test. The paper proposes a web application for evaluating tests using
an expert system in distance learning systems. The proposed web
application is appropriate for didactic tests or tests with results for
subsequent studying follow-up courses. The web application works
with test questions and uses an expert system and LFLC tool for test
evaluation. After test evaluation, the results are visualized and shown
to the student.
Abstract: The purpose of the study was to examine lifelong
education for teachers as a tool for achieving effective teaching and
learning. Lifelong education enhances social inclusion, personal
development, citizenship, employability, teaching and learning,
community and the nation. It is imperative that the teacher needs to
update his knowledge regularly to be able to perform optimally, since
he has a major position in the inculcation of desirable elements in
students, and the challenges of lifelong education were also
discussed. Descriptive survey design was adopted for the study. A
simple random sampling technique was used to select 80 teachers as
sample from a population of 105 senior secondary school teachers in
Makurdi Local Government Area of Benue State. A 20-item self
designed questionnaire subjected to expert validation and reliability
was used to collect data. The reliability Alpha coefficient of 0.87 was
established using Cronbach’s Alpha technique, mean scores and
standard deviation were used to answer the 2 research questions
while chi-square was used to analyse data for the 2 null hypotheses,
which states that lifelong education for teachers is not a significant
tool for achieving effective teaching and lifelong education for
teachers does not significantly impact on effective learning. The
findings of the study revealed that, lifelong education for teachers can
be used as a tool for achieving effective teaching and learning, and
the study recommended among others that government, organizations
and individuals should in collaboration put lifelong education
programmes for teachers on the priority list. The paper concluded
that the strategic position of lifelong education for teachers towards
enhanced teaching, learning and the production of quality manpower
in the society makes it imperative for all hands to be on “deck” to
support the programme financially and otherwise.
Abstract: The goal of this paper is proposing a supply chain
value dashboard in home appliance manufacturing firms to create
more value for all stakeholders via balanced scorecard approach.
Balanced scorecard is an effective approach that managers have used
to evaluate supply chain performance in many fields but there is a
lack of enough attention to all supply chain stakeholders, improving
value creation and, defining correlation between value indicators and
performance measuring quantitatively. In this research the key
stakeholders in home appliance supply chain, value indicators with
respect to create more value for stakeholders and the most important
metrics to evaluate supply chain value performance based on
balanced scorecard approach have been selected via literature review.
The most important indicators based on expert’s judgment acquired
by in survey focused on creating more value for. Structural equation
modelling has been used to disclose relations between value
indicators and balanced scorecard metrics. The important result of
this research is identifying effective value dashboard to create more
value for all stakeholders in supply chain via balanced scorecard
approach and based on an empirical study covering ten home
appliance manufacturing firms in Iran. Home appliance
manufacturing firms can increase their stakeholder's satisfaction by
using this value dashboard.
Abstract: People, throughout the history, have made estimates
and inferences about the future by using their past experiences.
Developing information technologies and the improvements in the
database management systems make it possible to extract useful
information from knowledge in hand for the strategic decisions.
Therefore, different methods have been developed. Data mining by
association rules learning is one of such methods. Apriori algorithm,
one of the well-known association rules learning algorithms, is not
commonly used in spatio-temporal data sets. However, it is possible
to embed time and space features into the data sets and make Apriori
algorithm a suitable data mining technique for learning spatiotemporal
association rules. Lake Van, the largest lake of Turkey, is a
closed basin. This feature causes the volume of the lake to increase or
decrease as a result of change in water amount it holds. In this study,
evaporation, humidity, lake altitude, amount of rainfall and
temperature parameters recorded in Lake Van region throughout the
years are used by the Apriori algorithm and a spatio-temporal data
mining application is developed to identify overflows and newlyformed
soil regions (underflows) occurring in the coastal parts of
Lake Van. Identifying possible reasons of overflows and underflows
may be used to alert the experts to take precautions and make the
necessary investments.
Abstract: The objective of this paper is to analyze the role played by the institute of the public hearings in the Brazilian Supreme Court. The public hearings are regulated since 1999 by the Brazilian Laws nº 9.868, nº 9.882 and by the Intern Regiment of the Brazilian Supreme Court. According to this legislation, the public hearings are supposed to be called when a matter of circumstance of fact must be clarified, what can be done through the hearing of the testimonies of persons with expertise and authority in the theme related to the cause. This work aims to investigate what is the role played by the public hearings and by the experts in the Brazilian Supreme Court. The hypothesis of this research is that: (I) The public hearings in the Brazilian Supreme Court are used to uphold a rhetoric of a democratic legitimacy of the Court`s decisions; (II) The Legislative intentions have been distorted. To test this hypothesis, the adopted methodology involves an empirical study of the Brazilian jurisprudence. As a conclusion, it follows that the public hearings convened by the Brazilian Supreme Court do not correspond, in practice, to the role assigned to them by the Congress since they do not serve properly to epistemic interests. The public hearings not only do not legitimate democratically the decisions, but also, do not properly clarify technical issues.
Abstract: Malaysia’s green building development is gaining
momentum and green buildings have become a key focus area,
especially within the commercial sector with the encouragement of
government legislation and policy. Due to the emerging awareness
among the market players’ views of the benefits associated with the
ownership of green buildings in Malaysia, there is a need for valuers
to incorporate consideration of sustainability into their assessments of
property market value to ensure the green buildings continue to
increase in the market. This paper analyses the valuers’ current
perception on the valuation practices with regard to the green issues
in Malaysia. The study was based on a survey of registered real estate
valuers and the experts whose work related to valuation in the Klang
Valley area to rate their view regarding the perception on valuation of
green building. The findings present evidence that even though
Malaysian valuers have limited knowledge of green buildings, they
recognise the importance of incorporating the green features in the
valuation process. The inclusion of incorporating the green features
in valuations in practice was hindered by the inadequacy of sufficient
transaction data in the market. Furthermore, valuers experienced
difficulty in identifying what are the various input parameters of
green building and how to adjust it in order to reflect the benefit of
sustainability features correctly in the valuation process. This paper
focuses on the present challenges confronted by Malaysian valuers
with regards to incorporating the green features in their valuation.
Abstract: It is an indispensible strategy to adopt greenery
approach on architectural bases so as to improve ecological habitats,
decrease heat-island effect, purify air quality, and relieve surface
runoff as well as noise pollution, all of which are done in an attempt to
achieve sustainable environment. How we can do with plant design to
attain the best visual quality and ideal carbon dioxide fixation depends
on whether or not we can appropriately make use of greenery
according to the nature of architectural bases. To achieve the goal, it is
a need that architects and landscape architects should be provided with
sufficient local references. Current greenery studies focus mainly on
the heat-island effect of urban with large scale. Most of the architects
still rely on people with years of expertise regarding the adoption and
disposition of plantation in connection with microclimate scale.
Therefore, environmental design, which integrates science and
aesthetics, requires fundamental research on landscape environment
technology divided from building environment technology. By doing
so, we can create mutual benefits between green building and the
environment. This issue is extremely important for the greening design
of the bases of green buildings in cities and various open spaces. The
purpose of this study is to establish plant selection and allocation
strategies under different building sunshade levels. Initially, with the
shading of sunshine on the greening bases as the starting point, the
effects of the shades produced by different building types on the
greening strategies were analyzed. Then, by measuring the PAR
(photosynthetic active radiation), the relative DLI (daily light integral)
was calculated, while the DLI Map was established in order to
evaluate the effects of the building shading on the established
environmental greening, thereby serving as a reference for plant
selection and allocation. The discussion results were to be applied in
the evaluation of environment greening of greening buildings and
establish the “right plant, right place” design strategy of multi-level
ecological greening for application in urban design and landscape
design development, as well as the greening criteria to feedback to the
eco-city greening buildings.
Abstract: In order to help the expert to validate association rules
extracted from data, some quality measures are proposed in the
literature. We distinguish two categories: objective and subjective
measures. The first one depends on a fixed threshold and on data
quality from which the rules are extracted. The second one consists
on providing to the expert some tools in the objective to explore and
visualize rules during the evaluation step. However, the number of
extracted rules to validate remains high. Thus, the manually mining
rules task is very hard. To solve this problem, we propose, in this
paper, a semi-automatic method to assist the expert during the
association rule's validation. Our method uses rule-based
classification as follow: (i) We transform association rules into
classification rules (classifiers), (ii) We use the generated classifiers
for data classification. (iii) We visualize association rules with their
quality classification to give an idea to the expert and to assist him
during validation process.
Abstract: This paper presents an approach of on-line control of
the state of technosphere and environment objects based on the
integration of Data Warehouse, OLAP and Expert systems
technologies. It looks at the structure and content of data warehouse
that provides consolidation and storage of monitoring data. There is a
description of OLAP-models that provide a multidimensional
analysis of monitoring data and dynamic analysis of principal
parameters of controlled objects. The authors suggest some criteria of
emergency risk assessment using expert knowledge about danger
levels. It is demonstrated now some of the proposed solutions could
be adopted in territorial decision making support systems.
Operational control allows authorities to detect threat, prevent natural
and anthropogenic emergencies and ensure a comprehensive safety of
territory.
Abstract: This paper presents an approach for the classification of
an unstructured format description for identification of file formats.
The main contribution of this work is the employment of data mining
techniques to support file format selection with just the unstructured
text description that comprises the most important format features for
a particular organisation. Subsequently, the file format indentification
method employs file format classifier and associated configurations to
support digital preservation experts with an estimation of required file
format. Our goal is to make use of a format specification knowledge
base aggregated from a different Web sources in order to select file
format for a particular institution. Using the naive Bayes method,
the decision support system recommends to an expert, the file format
for his institution. The proposed methods facilitate the selection of
file format and the quality of a digital preservation process. The
presented approach is meant to facilitate decision making for the
preservation of digital content in libraries and archives using domain
expert knowledge and specifications of file formats. To facilitate
decision-making, the aggregated information about the file formats is
presented as a file format vocabulary that comprises most common
terms that are characteristic for all researched formats. The goal is to
suggest a particular file format based on this vocabulary for analysis
by an expert. The sample file format calculation and the calculation
results including probabilities are presented in the evaluation section.
Abstract: Experts, enterprises and operators expect that the
bandwidth request will increase up to rates of 100 to 1,000 Mbps
within several years. Therefore the most important question is which
technology shall satisfy the future consumer broadband demands.
Currently the consensus is, that the fiber technology has the best
technical characteristics to achieve such the high bandwidth rates.
But fiber technology is so far very cost-intensive and resource
consuming. To avoid these investments, operators are concentrating
to upgrade the existing copper and hybrid fiber coax infrastructures.
This work presents a comparison of the copper and fiber
technologies including an overview about the current German
broadband market. Both technologies are reviewed in the terms of
demand, willingness to pay and economic efficiency in connection
with the technical characteristics.
Abstract: To solve these problems, we investigated the management system of heating enterprise, including strategic planning based on the balanced scorecard (BSC), quality management in accordance with the standards of the Quality Management System (QMS) ISO 9001 and analysis of the system based on expert judgment using fuzzy inference. To carry out our work we used the theory of fuzzy sets, the QMS in accordance with ISO 9001, BSC, method of construction of business processes according to the notation IDEF0, theory of modeling using Matlab software simulation tools and graphical programming LabVIEW. The results of the work are as follows: We determined possibilities of improving the management of heat-supply plant-based on QMS; after the justification and adaptation of software tool it has been used to automate a series of functions for the management and reduction of resources and for the maintenance of the system up to date; an application for the analysis of the QMS based on fuzzy inference has been created with novel organization of communication software with the application enabling the analysis of relevant data of enterprise management system.
Abstract: Total Quality Management (TQM) is a managerial
approach that improves the competitiveness of the industry,
meanwhile Information technology (IT) was introduced with TQM
for handling the technical issues which is supported by quality
experts for fulfilling the customers’ requirement. Present paper aims
to utilise AHP (Analytic Hierarchy Process) methodology to
priorities and rank the hierarchy levels of TQM enablers and IT
resource together for its successful implementation in the Information
and Communication Technology (ICT) industry. A total of 17 TQM
enablers (nine) and IT resources (eight) were identified and
partitioned into 3 categories and were prioritised by AHP approach.
The finding indicates that the 17 sub-criteria can be grouped into
three main categories namely organizing, tools and techniques, and
culture and people. Further, out of 17 sub-criteria, three sub-criteria:
top management commitment and support, total employee
involvement, and continuous improvement got highest priority
whereas three sub-criteria such as structural equation modelling,
culture change, and customer satisfaction got lowest priority. The
result suggests a hierarchy model for ICT industry to prioritise the
enablers and resources as well as to improve the TQM and IT
performance in the ICT industry. This paper has some managerial
implication which suggests the managers of ICT industry to
implement TQM and IT together in their organizations to get
maximum benefits and how to utilize available resources. At the end,
conclusions, limitation, future scope of the study are presented.