Abstract: Some of the polycyclic aromatic hydrocarbons (PAHs)
are the strongest known carcinogens compounds; the majority of
them are mostly produced by the incomplete combustion of fossil
fuels; Motor vehicles are a significant source of polycyclic aromatic
hydrocarbon (PAH) where diesel emission is one of the main sources
of such compounds available in the ambient air. There is a big
concern about the increasing concentration of PAHs in the
environment. Researchers are trying to explore optimal methods to
reduce those pollutants and improve the quality of air. Water blended
fuel is one of the possible approaches to reduce emission of PAHs
from the combustion of diesel in urban and domestic vehicles. In this
work a modeling study was conducted using CHEMKIN-PRO
software to simulate spray combustion at similar diesel engine
conditions. Surrogate fuel of (80 % n-heptane and 20 % toluene) was
used due to detailed kinetic and thermodynamic data needed for
modeling is available for this kind of fuel but not available for diesel.
An emulsified fuel with 3, 5, 8, 10 and 20 % water by volume is used
as an engine feed for this study. The modeling results show that water
has a significant effect on reducing engine soot and PAHs precursors
formation up to certain extent.
Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: This paper address the network reliability optimization
problem in the optical access network design for the 3G cellular
systems. We presents a novel 0-1 integer programming model for
designing optical access network topologies comprised of multi-rings
with common-edge in order to guarantee always-on services. The
results show that the proposed model yields access network
topologies with the optimal reliablity and satisfies both network cost
limitations and traffic demand requirements.
Abstract: This paper explores the extent of the gap in poverty rates between immigrant and native households in Spanish regions and assess to what extent regional differences in individual and contextual characteristics can explain the divergences in such a gap. By using multilevel techniques and European Union Survey on Income and Living Conditions, we estimate immigrant households experiments an increase of 76 per cent in the odds of being poor compared with a native one when we control by individual variables. In relation to regional differences in the risk of poverty, regionallevel variables have higher effect in the reduction of these differences than individual variables.
Abstract: Structured phospholipids from commercial soybean
lecithin with oil enriched omega-3 fatty acid form by product of tuna
canning is alternative procedure to provides the stability of omega-3
fatty acid structure and increase these bioactive function in
metabolism. Best treatment condition was obtain in 18 hours
acidolysis reaction with 30% enzyme concentration, which EPADHA
incorporation level was 127,47 mg/g and incorporation
percentage of EPA-DHA was 51,04% at phospholipids structure.
This structured phospolipids could reduce atherosclerosis risk in
male Sprague dawley rat. Provision of structured phospholipids has
significant effect (α = 0.05) on changes in lipid profile, intima-media
thickness of aorta rats (male Sprague dawley) fed atherogenic diet.
Structured phospholipids intake can lower total cholesterol 78.36
mg/dL, total triglycerides 94,57 mg/dL, LDL levels 87.08 mg/dL and
increased HDL level as much as 12,64 mg/dL in 10 weeks cares.
Structured phospholipids intake also can prevent the thickening of
the intima-media layer of the aorta.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: Study investigates the level and extent of voluntary disclosure practice in Croatia. The research was conducted on the sample of 130 medium and large companies. Findings indicate that two thirds of the companies analyzed disclose below-average number of additional information. The explanatory analyses has shown that firm size, listing status and industrial sector significantly and positively affect the level and extent of voluntary disclosure in the annual report of Croatian companies. On the other hand, profitability and ownership structure were found statistically insignificant. Unlike previous studies, this paper deals with level of voluntary disclosure of medium and large companies, as well as companies whose shares are not listed on the organized capital market, which can be found as our contribution. Also, the research makes contribution by providing the insights into voluntary disclosure practices in Croatia, as a case of macro-oriented accounting system economy, i.e. bank oriented economy with an emerging capital market.
Abstract: The objective of this paper is to characterize the spontaneous Electroencephalogram (EEG) signals of four different motor imagery tasks and to show hereby a possible solution for the present binary communication between the brain and a machine ora Brain-Computer Interface (BCI). The processing technique used in this paper was the fractal analysis evaluated by the Critical Exponent Method (CEM). The EEG signal was registered in 5 healthy subjects,sampling 15 measuring channels at 1024 Hz.Each channel was preprocessed by the Laplacian space ltering so as to reduce the space blur and therefore increase the spaceresolution. The EEG of each channel was segmented and its Fractaldimension (FD) calculated. The FD was evaluated in the time interval corresponding to the motor imagery and averaged out for all the subjects (each channel). In order to characterize the FD distribution,the linear regression curves of FD over the electrodes position were applied. The differences FD between the proposed mental tasks are quantied and evaluated for each experimental subject. The obtained results of the proposed method are a substantial fractal dimension in the EEG signal of motor imagery tasks and can be considerably utilized as the multiple-states BCI applications.
Abstract: In the time of globalisation, growing uncertainty, ambiguity and change, traditional way of doing business are no longer sufficient and it is important to consider non-conventional methods and approaches to release creativity and facilitate innovation and growth. Thus, creative industries, as a natural source of creativity and innovation, draw particular attention. This paper explores feasibility of building creative partnerships between creative industries and business and brings attention to mutual benefits derived from such partnerships. Design/approach - This paper is a theoretical exploration of projects, practices and research findings addressing collaboration between creative industries and business. Thus, it concerns creative industries, arts, business and its representatives in order to define requirements for creative partnerships to work and succeed. Findings – Current practices in engaging into arts-business partnerships are still very few, although most of creative partnerships proved to be highly valuable and mutually beneficial. Certain conditions shall be provided in order to benefit from arts-business creative synergy. Originality/value- By integrating different sources of literature, this article provides a base for conducting empirical research in several dimensions within arts-business partnerships.
Abstract: Background: Blunt aortic trauma (BAT) includes
various morphological changes that occur during deceleration,
acceleration and/or body compression in traffic accidents. The
various forms of BAT, from limited laceration of the intima to
complete transection of the aorta, depends on the force acting on the
vessel wall and the tolerance of the aorta to injury. The force depends
on the change in velocity, the dynamics of the accident and of the
seating position in the car. Tolerance to aortic injury depends on the
anatomy, histological structure and pathomorphological alterations
due to aging or disease of the aortic wall.
An overview of the literature and medical documentation reveals
that different terms are used to describe certain forms of BAT, which
can lead to misinterpretation of findings or diagnoses. We therefore,
propose a classification that would enable uniform systematic
screening of all forms of BAT. We have classified BAT into three
morphologycal types: TYPE I (intramural), TYPE II (transmural) and
TYPE III (multiple) aortic ruptures with appropriate subtypes.
Methods: All car accident casualties examined at the Institute of
Forensic Medicine from 2001 to 2009 were included in this
retrospective study. Autopsy reports were used to determine the
occurrence of each morphological type of BAT in deceased drivers,
front seat passengers and other passengers in cars and to define the
morphology of BAT in relation to the accident dynamics and the age
of the fatalities.
Results: A total of 391 fatalities in car accidents were included in
the study. TYPE I, TYPE II and TYPE III BAT were observed in
10,9%, 55,6% and 33,5%, respectively. The incidence of BAT in
drivers, front seat and other passengers was 36,7%, 43,1% and
28,6%, respectively. In frontal collisions, the incidence of BAT was
32,7%, in lateral collisions 54,2%, and in other traffic accidents
29,3%. The average age of fatalities with BAT was 42,8 years and of
those without BAT 39,1 years.
Conclusion: Identification and early recognition of the risk factors
of BAT following a traffic accident is crucial for successful treatment
of patients with BAT. Front seat passengers over 50 years of age who
have been injured in a lateral collision are the most at risk of BAT.
Abstract: One of the most important applications of
wireless sensor networks is data collection. This paper
proposes as efficient approach for data collection in wireless
sensor networks by introducing Member Forward List. This list
includes the nodes with highest priority for forwarding the data.
When a node fails or dies, this list is used to select the next node
with higher priority. The benefit of this node is that it prevents
the algorithm from repeating when a node fails or dies. The
results show that Member Forward List decreases power
consumption and latency in wireless sensor networks.
Abstract: This paper presents the design and implementation of CASTE, a Cloud-based automatic software test environment. We first present the architecture of CASTE, then the main packages and classes of it are described in detail. CASTE is built upon a private Infrastructure as a Service platform. Through concentrated resource management of virtualized testing environment and automatic execution control of test scripts, we get a better solution to the testing resource utilization and test automation problem. Experiments on CASTE give very appealing results.
Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a micropolar fluid in the
presence of magnetic field and both homogeneous and heterogeneous
chemical reactions. The average effective dispersion coefficient has
been found using Taylor-s limiting condition under long wavelength
approximation. The effects of various relevant parameters on the average
coefficient of dispersion have been studied. The average effective
dispersion coefficient increases with amplitude ratio, cross viscosity
coefficient and heterogeneous chemical reaction rate parameter. But it
decreases with magnetic field parameter and homogeneous chemical
reaction rate parameter. It can be noted that the presence of peristalsis
enhances dispersion of a solute.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: Real-time hand tracking is a challenging task in many
computer vision applications such as gesture recognition. This paper
proposes a robust method for hand tracking in a complex environment
using Mean-shift analysis and Kalman filter in conjunction with 3D
depth map. The depth information solve the overlapping problem
between hands and face, which is obtained by passive stereo measuring
based on cross correlation and the known calibration data of
the cameras. Mean-shift analysis uses the gradient of Bhattacharyya
coefficient as a similarity function to derive the candidate of the hand
that is most similar to a given hand target model. And then, Kalman
filter is used to estimate the position of the hand target. The results
of hand tracking, tested on various video sequences, are robust to
changes in shape as well as partial occlusion.
Abstract: Waste lubricating oil re-refining adsorption process by
different adsorbent materials was investigated. Adsorbent materials
such as oil adsorbent, egg shale powder, date palm kernel powder,
and acid activated date palm kernel powder were used. The
adsorption process over fixed amount of adsorbent at ambient
conditions was investigated. The adsorption/extraction process was
able to deposit the asphaltenic and metallic contaminants from the
waste oil to lower values. It was found that the date palm kernel
powder with contact time of 4 h was able to give the best conditions
for treating the waste oil. The recovered solvent could be also reused.
It was also found that the activated bentonite gave the best
physical properties followed by the date palm kernel powder.
Abstract: Cavitation in pumps is known as the formation of
vapor bubbles due to pressure drop and collapsing these bubbles. In
some conditions, it has been observed that the formation of bubbles
occurs at the pressure side of centrifugal pump blades. In this study,
the formation of bubbles at the pressure side of blades has been
investigated. Water is used in this study as the fluid and performance
curves were depicted for different flow rates in an approximately
constant speed. The results show that when a centrifugal pump works
in low flow rates, a secondary flow namely recirculation starts to
begin. In this condition, separation of flow increases which causes
vortex formation and local pressure drop and eventually the
formation of vapor bubbles starts.
Abstract: These Nowadays the explosion of bombs or explosive
materials such as gas and oil near or inside the buildings cause some
losses in installations and building components. This has made the
engineers to make the buildings and their components resistance
against the effects of explosion. These activities lead to provide
regulations and different methods. The above regulations are mostly
focused on the explosion effects resulting from the vehicles around
the buildings. Therefore, the explosion resulting from the vehicles
outside the buildings will be studied in this research.
In the present study, the main goals are to investigate the
explosion load effects on the structures located on the piles with the
specific quantity of plasticity and observing the permissible response
of these structures. The concentrated mass system and the spring with
two degree of freedom will be used to study the structural system.
Abstract: Sequential pattern mining is a challenging task in data mining area with large applications. One among those applications is mining patterns from weblog. Recent times, weblog is highly dynamic and some of them may become absolute over time. In addition, users may frequently change the threshold value during the data mining process until acquiring required output or mining interesting rules. Some of the recently proposed algorithms for mining weblog, build the tree with two scans and always consume large time and space. In this paper, we build Revised PLWAP with Non-frequent Items (RePLNI-tree) with single scan for all items. While mining sequential patterns, the links related to the nonfrequent items are not considered. Hence, it is not required to delete or maintain the information of nodes while revising the tree for mining updated transactions. The algorithm supports both incremental and interactive mining. It is not required to re-compute the patterns each time, while weblog is updated or minimum support changed. The performance of the proposed tree is better, even the size of incremental database is more than 50% of existing one. For evaluation purpose, we have used the benchmark weblog dataset and found that the performance of proposed tree is encouraging compared to some of the recently proposed approaches.