Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: Image Searching was always a problem specially when these images are not properly managed or these are distributed over different locations. Currently different techniques are used for image search. On one end, more features of the image are captured and stored to get better results. Storing and management of such features is itself a time consuming job. While on the other extreme if fewer features are stored the accuracy rate is not satisfactory. Same image stored with different visual properties can further reduce the rate of accuracy. In this paper we present a new concept of using polynomials of sorted histogram of the image. This approach need less overhead and can cope with the difference in visual features of image.
Abstract: A manufacturing inventory model with shortages with
carrying cost, shortage cost, setup cost and demand quantity as
imprecise numbers, instead of real numbers, namely interval number
is considered here. First, a brief survey of the existing works on
comparing and ranking any two interval numbers on the real line
is presented. A common algorithm for the optimum production
quantity (Economic lot-size) per cycle of a single product (so as
to minimize the total average cost) is developed which works well
on interval number optimization under consideration. Finally, the
designed algorithm is illustrated with numerical example.
Abstract: In this paper, we propose a Perceptually Optimized Embedded ZeroTree Image Coder (POEZIC) that introduces a perceptual weighting to wavelet transform coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to the coding quality obtained using the SPIHT algorithm only. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEZIC quality assessment. Our POEZIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) luminance masking and Contrast masking, 2) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting, 3) the Wavelet Error Sensitivity WES used to reduce the perceptual quantization errors. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: The mechanical quadrature methods for solving the boundary integral equations of the anisotropic Darcy-s equations with Dirichlet conditions in smooth domains are presented. By applying the collectively compact theory, we prove the convergence and stability of approximate solutions. The asymptotic expansions for the error show that the methods converge with the order O (h3), where h is the mesh size. Based on these analysis, extrapolation methods can be introduced to achieve a higher convergence rate O (h5). An a posterior asymptotic error representation is derived in order to construct self-adaptive algorithms. Finally, the numerical experiments show the efficiency of our methods.
Abstract: A large quantity of world-s oil reserves exists in
carbonate reservoirs. Carbonate reservoirs are very sensitive to
chemical enhanced oil recovery process because of containing large
amount of calcite, dolomite and calcium sulfate minerals. These
minerals cause major obstacles during alkali-surfactant-polymer
(ASP) flooding. Alkali reacts with these minerals and form undesired
precipitations which plug effective porous openings, reduce
permeability and cause scale occurrence at the wellbore. In this
paper, a new chemical combination consists of acrylic acid and alkali
was used to minimize precipitation problem during ASP flooding. A
series of fluid-fluid compatibility tests were performed using acrylic
acid and different concentrations of alkaline. Two types of alkalis
namely; sodium carbonate and sodium metaborate were screened. As
a result, the combination of acrylic acid and sodium carbonate was
not effective in preventing calcium and magnesium precipitations.
However, acrylic acid and sodium metaborate showed promising
results for keeping all solutions without any precipitations. The ratio
of acrylic acid to sodium metaborate of 0.7:1.0 was found to be
optimum for achieving a compatible solution for 30 days at 80oC.
Abstract: An iterative definition of any n variable mean function is given in this article, which iteratively uses the two-variable form of the corresponding two-variable mean function. This extension method omits recursivity which is an important improvement compared with certain recursive formulas given before by Ando-Li-Mathias, Petz- Temesi. Furthermore it is conjectured here that this iterative algorithm coincides with the solution of the Riemann centroid minimization problem. Certain simulations are given here to compare the convergence rate of the different algorithms given in the literature. These algorithms will be the gradient and the Newton mehod for the Riemann centroid computation.
Abstract: Bones are dynamic and responsive organs, they
regulate their strength and mass according to the loads which they are subjected. Because, the Wnt/β-catenin pathway has profound
effects on the regulation of bone mass, we hypothesized that mechanical loading of bone cells stimulates Wnt/β-catenin signaling, which results in the generation of new bone mass.
Mechanical loading triggers the secretion of the Wnt molecule, which after binding to transmembrane proteins, causes GSK-3β (Glycogen synthase kinase 3 beta) to cease the phosphorylation of β-catenin. β-catenin accumulation in the cytoplasm, followed by its
transport into the nucleus, binding to transcription factors (TCF/LEF)
that initiate transcription of genes related to bone formation. To test this hypothesis, we used TOPGAL (Tcf Optimal Promoter
β-galactosidase) mice in an experiment in which cyclic loads were
applied to the forearm. TOPGAL mice are reporters for cells effected
by the Wnt/β-catenin signaling pathway. TOPGAL mice are genetically engineered mice in which transcriptional activation of β-
catenin, results in the production of an enzyme, β-galactosidase. The
presence of this enzyme allows us to localize transcriptional
activation of β-catenin to individual cells, thereby, allowing us to quantify the effects that mechanical loading has on the Wnt/β-catenin pathway and new bone formation. The ulnae of loaded TOPGAL
mice were excised and transverse slices along different parts of the
ulnar shaft were assayed for the presence of β-galactosidase.
Our results indicate that loading increases β-catenin transcriptional
activity in regions where this pathway is already primed (i.e. where basal activity is already higher) in a load magnitude dependent
manner. Further experiments are needed to determine the temporal and spatial activation of this signaling in relation to bone formation.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.
Abstract: This paper argues that networks, such as the ECN and the American network, are affected by certain small events which are inherent to path dependence and preclude the full evolution towards efficiency. It is advocated that the American network is superior to the ECN in many respects due to its greater flexibility and longer history. This stems in particular from the creation of the American network, which was based on a small number of cases. Such a structure encourages further changes and modifications which are not necessarily radical. The ECN, by contrast, was established by legislative action, which explains its rigid structure and resistance to change. This paper is an attempt to transpose the superiority of the American network on to the ECN. It looks at concepts such as judicial cooperation, harmonisation of procedure, peer review and regulatory impact assessments (RIAs), and dispute resolution procedures.
Abstract: We introduce an adaptive technique for the joint mitigation of transients and continuous-wave radio-frequency co-channel interference (CW RFI) in high-frequency (HF) over-the-horizon radars (OTHRs). The performance of this technique is illustrated using data from an operational surface-wave radar (SECAR) and from recent experimental trials with sky-wave (SW) and sky-wave–line-of-sight (SKYLOS) HF OTHRs.
Abstract: In this study, a longitudinal joint connection was
proposed for the short-span slab-type modular bridges with rapid
construction. The slab-type modular bridge consists of a number of
precast slab modules and has the joint connection between the
modules in the longitudinal direction of the bridge. A finite element
based parameter analysis was conducted to design the shape and the
dimensions of the longitudinal joint connection. Numbers of shear
keys within the joint, height and depth of the shear key, tooth angle,
and the spacing were considered as the design parameters. Using the
local cracking load at the corner of the shear key and the
cross-sectional area of the joint, an efficiency factor was proposed to
evaluate the effectiveness of the longitudinal joint connection. The
dimensions of shear key were determined by comparing the cracking
loads and the efficiency factors obtained from the finite element
analysis.
Abstract: In this paper, we investigate the strategic stochastic air traffic flow management problem which seeks to balance airspace capacity and demand under weather disruptions. The goal is to reduce the need for myopic tactical decisions that do not account for probabilistic knowledge about the NAS near-future states. We present and discuss a scenario-based modeling approach based on a time-space stochastic process to depict weather disruption occurrences in the NAS. A solution framework is also proposed along with a distributed implementation aimed at overcoming scalability problems. Issues related to this implementation are also discussed.
Abstract: Many foreign and Lithuanian scientists, analyzing the
evaluation of the tax system in respect of the burden of taxation,
agree that the latter, in principle, depends on how many individuals
and what units of the residents constitute a household. Therefore, the
aim of scientific research is to substantiate or to deny the significance
of a household, but not a resident, as a statistical unit, during the
evaluation of tax system, to be precise, determination of the value of
the burden of taxation. A performed scientific research revealed that
evaluation of the tax system in respect of a household, but not a
resident, as a statistical unit, allows not only to evaluate the
efficiency of the tax system more objectively, but also to forecast
practicably existing poverty line, burden of taxation, and to
capacitate the initiation of efficient decisions in social and tax fields
creating the environment of existence.
Abstract: Crime is a major societal problem for most of the
world's nations. Consequently, the police need to develop new
methods to improve their efficiency in dealing with these ever increasing crime rates. Two of the common difficulties that the police
face in crime control are crime investigation and the provision of crime information to the general public to help them protect themselves. Crime control in police operations involves the use of
spatial data, crime data and the related crime data from different organizations (depending on the nature of the analysis to be made).
These types of data are collected from several heterogeneous sources
in different formats and from different platforms, resulting in a lack of standardization. Moreover, there is no standard framework for
crime data collection, integration and dissemination through mobile
devices. An investigation into the current situation in crime control was carried out to identify the needs to resolve these issues. This
paper proposes and investigates the use of service oriented
architecture (SOA) and the mobile spatial information service in crime control. SOA plays an important role in crime control as an
appropriate way to support data exchange and model sharing from
heterogeneous sources. Crime control also needs to facilitate mobile
spatial information services in order to exchange, receive, share and release information based on location to mobile users anytime and
anywhere.
Abstract: The possibility of using cassava residue containing
49.66% starch, 21.47% cellulose, 12.97% hemicellulose, and 21.86%
lignin as a raw material to produce glucose using enzymatic
hydrolysis was investigated. In the experiment, each reactor
contained the cassava residue, bacteria cells, and production medium.
The effects of particles size (40 mesh and 60 mesh) and strains of
bacteria (A002 and M015) isolated from Thai higher termites,
Microcerotermes sp., on the glucose concentration at 37°C were
focused. High performance liquid chromatography (HPLC) with a
refractive index detector was used to determine the quantity of
glucose. The maximum glucose concentration obtained at 37°C using
strain A002 and 60 mesh of the cassava residue was 1.51 g/L at 10 h.