Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: PDMS (Polydimethylsiloxane) polymer is a suitable material for biological and MEMS (Microelectromechanical systems) designers, because of its biocompatibility, transparency and high resistance under plasma treatment. PDMS round channel is always been of great interest due to its ability to confine the liquid with membrane type micro valves. In this paper we are presenting a very simple way to form round shapemicrofluidic channel, which is based on reflow of positive photoresist AZ® 40 XT. With this method, it is possible to obtain channel of different height simply by varying the spin coating parameters of photoresist.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: Recently, a great amount of interest has been shown
in the field of modeling and controlling hybrid systems. One of the
efficient and common methods in this area utilizes the mixed logicaldynamical
(MLD) systems in the modeling. In this method, the
system constraints are transformed into mixed-integer inequalities by
defining some logic statements. In this paper, a system containing
three tanks is modeled as a nonlinear switched system by using the
MLD framework. Comparing the model size of the three-tank system
with that of a two-tank system, it is deduced that the number of
binary variables, the size of the system and its complexity
tremendously increases with the number of tanks, which makes the
control of the system more difficult. Therefore, methods should be
found which result in fewer mixed-integer inequalities.
Abstract: Tool Tracker is a client-server based application. It is essentially a catalogue of various network monitoring and management tools that are available online. There is a database maintained on the server side that contains the information about various tools. Several clients can access this information simultaneously and utilize this information. The various categories of tools considered are packet sniffers, port mappers, port scanners, encryption tools, and vulnerability scanners etc for the development of this application. This application provides a front end through which the user can invoke any tool from a central repository for the purpose of packet sniffing, port scanning, network analysis etc. Apart from the tool, its description and the help files associated with it would also be stored in the central repository. This facility will enable the user to view the documentation pertaining to the tool without having to download and install the tool. The application would update the central repository with the latest versions of the tools. The application would inform the user about the availability of a newer version of the tool currently being used and give the choice of installing the newer version to the user. Thus ToolTracker provides any network administrator that much needed abstraction and ease-ofuse with respect to the tools that he can use to efficiently monitor a network.
Abstract: Role of acoustic driving pressure on the
translational-radial dynamics of a moving single bubble
sonoluminescence (m-SBSL) has been numerically
investigated. The results indicate that increase in the
amplitude of the driving pressure leads to increase in the
bubble peak temperature. The length and the shape of the
trajectory of the bubble depends on the acoustic pressure and
because of the spatially dependence of the radial dynamics of
the moving bubble, its peak temperature varies during the
acoustical pulses. The results are in good agreement with the
experimental reports on m-SBSL.
Abstract: EGOTHOR is a search engine that indexes the Web
and allows us to search the Web documents. Its hit list contains URL
and title of the hits, and also some snippet which tries to shortly
show a match. The snippet can be almost always assembled by an
algorithm that has a full knowledge of the original document (mostly
HTML page). It implies that the search engine is required to store
the full text of the documents as a part of the index.
Such a requirement leads us to pick up an appropriate compression
algorithm which would reduce the space demand. One of the solutions
could be to use common compression methods, for instance gzip or
bzip2, but it might be preferable if we develop a new method which
would take advantage of the document structure, or rather, the textual
character of the documents.
There already exist a special compression text algorithms and
methods for a compression of XML documents. The aim of this
paper is an integration of the two approaches to achieve an optimal
level of the compression ratio
Abstract: Polyurethane foam (PUF) were prepared by
reacting polyols synthesized from soy-oil into mixture of 2,4-
Toluene diisocyanate (TDI) with 4,4--Methylene Diamine
Isocyanate (MDI) with ratio of 70:30. The polyols obtained
via esterification reaction were categorize into different
temperature of reaction and by used of varied concentration
of phosphoric acid catalyst. The purpose of catalysts is to
shifting selectivity to a desired and value added of product.
The effect of stoichiometric balance (molar ratio of
epoxide/ethylene glycol) to the concentration of the catalyst
on the final properties was evaluated.
Abstract: The aim of this paper is to express the input-output
matrix as a linear ordering problem which is classified as an NP-hard
problem. We then use a Tabu search algorithm to find the best
permutation among sectors in the input-output matrix that will give
an optimal solution. This optimal permutation can be useful in
designing policies and strategies for economists and government in
their goal of maximizing the gross domestic product.
Abstract: In order to study pressed pile test and ultimate bearing
capacity character of large-diameter steel pipe pile, based on two high-piled wharfs of Zhanjiang Port, pressed pile test and numerical simulation of three large-diameter steel pipe piles are analyzed in this
paper. Anchored pile method is used to pressed pile test, and the
curves of Q-s and ultimate bearing capacity are attained. Then the three piles are numerically simulated by ABAQUS, and results of numerical simulation and those of field test are comparatively analyzed. The results show that settlement value of numerical
simulation is larger than that of field test in the process of loading, the difference value is widening with the increasing of load, and the
ultimate difference value of settlement is 20% to 30%.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: The data exchanged on the Web are of different nature
from those treated by the classical database management systems;
these data are called semi-structured data since they do not have a
regular and static structure like data found in a relational database;
their schema is dynamic and may contain missing data or types.
Therefore, the needs for developing further techniques and
algorithms to exploit and integrate such data, and extract relevant
information for the user have been raised. In this paper we present
the system OSIX (Osiris based System for Integration of XML
Sources). This system has a Data Warehouse model designed for the
integration of semi-structured data and more precisely for the
integration of XML documents. The architecture of OSIX relies on
the Osiris system, a DL-based model designed for the representation
and management of databases and knowledge bases. Osiris is a viewbased
data model whose indexing system supports semantic query
optimization. We show that the problem of query processing on a
XML source is optimized by the indexing approach proposed by
Osiris.
Abstract: Business process modeling has become an accepted
means for designing and describing business operations. Thereby,
consistency of business process models, i.e., the absence of modeling
faults, is of upmost importance to organizations. This paper presents
a concept and subsequent implementation for detecting faults in
business process models and for computing a measure of their
consistency. It incorporates not only syntactic consistency but also
semantic consistency, i.e., consistency regarding the meaning of
model elements from a business perspective.
Abstract: The study of tourist activities and the mapping of their routes in space and time has become an important issue in tourism management. Here we represent space-time paths for the tourism industry by visualizing individual tourist activities and the paths followed using a 3D Geographic Information System (GIS). Considerable attention has been devoted to the measurement of accessibility to shopping, eating, walking and other services at the tourist destination. I turns out that GIS is a useful tool for studying the spatial behaviors of tourists in the area. The value of GIS is especially advantageous for space-time potential path area measures, especially for the accurate visualization of possible paths through existing city road networks. This study seeks to apply space-time concepts with a detailed street network map obtained from Google Maps to measure tourist paths both spatially and temporally. These paths are further determined based on data obtained from map questionnaires regarding the trip activities of 40 individuals. The analysis of the data makes it possible to determining the locations of the more popular paths. The results can be visualized using 3D GIS to show the areas and potential activity opportunities accessible to tourists during their travel time.
Abstract: The influence of viscosity on droplet diameter for
water-in-crude oil (w/o) emulsion with two different ratios; 20-80 %
and 50-50 % w/o emulsion was examined in the Brookfield
Rotational Digital Rheometer. The emulsion was prepared with
sorbitan sesquiolate (Span 83) act as emulsifier at varied temperature
and stirring speed in rotation per minute (rpm). Results showed that
the viscosity of w/o emulsion was strongly augmented by increasing
volume of water and decreased the temperature. The changing of
viscosity also altered the droplet size distribution. Changing of
droplet diameter was depends on the viscosity and the behavior of
emulsion either Newtonian or non-Newtonian.
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is of fundamental importance because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in developed countries, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we study the factors that influence exclusive breastfeeding and use the Generalized Poisson regression model to analyze the practices of exclusive breastfeeding in Mauritius. We develop two sets of quasi-likelihood equations (QLE)to estimate the parameters.
Abstract: Although many studies on the assembly technology of
the bridge construction have dealt mostly with on the pier, girder or the
deck of the bridge, studies on the prefabricated barrier have rarely been
performed. For understanding structural characteristics and
application of the concrete barrier in the modular bridge, which is an
assembly of structure members, static loading test was performed.
Structural performances as a road barrier of the three methods,
conventional cast-in-place(ST), vertical bolt connection(BVC) and
horizontal bolt connection(BHC) were evaluated and compared
through the analyses of load-displacement curves, strain curves of the
steel, concrete strain curves and the visual appearances of crack
patterns. The vertical bolt connection(BVC) method demonstrated
comparable performance as an alternative to conventional
cast-in-place(ST) while providing all the advantages of prefabricated
technology. Necessities for the future improvement in nuts
enforcement as well as legal standard and regulation are also
addressed.
Abstract: The present paper considers the steady free convection
boundary layer flow of a viscoelastic fluid on solid sphere with
Newtonian heating. The boundary layer equations are an order higher
than those for the Newtonian (viscous) fluid and the adherence
boundary conditions are insufficient to determine the solution of
these equations completely. Thus, the augmentation an extra
boundary condition is needed to perform the numerical
computational. The governing boundary layer equations are first
transformed into non-dimensional form by using special
dimensionless group and then solved by using an implicit finite
difference scheme. The results are displayed graphically to illustrate
the influence of viscoelastic K and Prandtl Number Pr parameters on
skin friction, heat transfer, velocity profiles and temperature profiles.
Present results are compared with the published papers and are found
to concur very well.
Abstract: This paper discuss the separation of the miscible
liquids by means of fractional distillation. For complete separation of
liquids, the process of heating, condensation, separation and storage
is done automatically to achieve the objective. PIC micro-controller
has been used to control each and every process of the work. The
controller also controls the storage process by activating and deactivating
the conveyors. The liquids are heated which on reaching
their respective boiling points evaporate and enter the condensation
chamber where they convert into liquid. The liquids are then directed
to their respective tanks by means of stepper motor which moves in
three directions, each movement into different tank. The tank on
filling sends the signal to controller which then opens the solenoid
valves. The tank is emptied into the beakers below the nozzle. As the
beaker filled, the nozzle closes and the conveyors come into
operation. The filled beaker is replaced by an empty beaker from
behind. The work can be used in oil industries, chemical industries
and paint industries.