Abstract: It is known that the heart interacts with and adapts to its venous and arterial loading conditions. Various experimental studies and modeling approaches have been developed to investigate the underlying mechanisms. This paper presents a model of the left ventricle derived based on nonlinear stress-length myocardial characteristics integrated over truncated ellipsoidal geometry, and second-order dynamic mechanism for the excitation-contraction coupling system. The results of the model presented here describe the effects of the viscoelastic damping element of the electromechanical coupling system on the hemodynamic response. Different heart rates are considered to study the pacing effects on the performance of the left-ventricle against constant preload and afterload conditions under various damping conditions. The results indicate that the pacing process of the left ventricle has to take into account, among other things, the viscoelastic damping conditions of the myofilament excitation-contraction process. The effects of left ventricular dimensions on the hemdynamic response have been examined. These effects are found to be different at different viscoelastic and pacing conditions.
Abstract: This study was set to determine the antimicrobial
activities of brine salting, chlorinated solution, and oil frying
treatments on enteric bacteria and fungi in Rastrineobola argentea
fish from fish landing beaches within L. Victoria basin of western
Kenya. Statistical differences in effectiveness of the different
treatment methods was determined by single factor ANOVA, and
paired two-tail t-Test was performed to compare the differences in
moisture contents before and after storage. Oil fried fish recorded the
lowest microbial loads, sodium chloride at 10% concentration was
the second most effective and chlorinated solution even at 150ppm
was the least effective against the bacteria and fungi in fish. Moisture
contents of the control and treated fish were significantly lower after
storage. These results show that oil frying of fish should be adopted
for processing and preserving Rastrineobola argentea which is the
most abundant and affordable fish species from Lake Victoria.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: The scientific achievements coming from molecular
biology depend greatly on the capability of computational
applications to analyze the laboratorial results. A comprehensive
analysis of an experiment requires typically the simultaneous study
of the obtained dataset with data that is available in several distinct
public databases. Nevertheless, developing a centralized access to
these distributed databases rises up a set of challenges such as: what
is the best integration strategy, how to solve nomenclature clashes,
how to solve database overlapping data and how to deal with huge
datasets. In this paper we present GeNS, a system that uses a simple and yet innovative approach to address several biological data integration issues. Compared with existing systems, the main
advantages of GeNS are related to its maintenance simplicity and to its coverage and scalability, in terms of number of supported
databases and data types. To support our claims we present the current use of GeNS in two concrete applications. GeNS currently contains more than 140 million of biological relations and it can be
publicly downloaded or remotely access through SOAP web services.
Abstract: This paper introduces application of multi degree of freedom fuzzy(MDOFF) controller in permanent magnet (PM)drive system. The drive system model is developed for FO control. Simulation of the system is carried out to predict the performance at NL and under load,. The results indicate that application of MDOFF controller is effective for sensorless PM drive system.
Abstract: Intradiscal and intervertebral pressure transducers
were developed. They were used to map the pressures in the nucleus
and within the annulus of the human spinal segments. Their stressrelaxation
were recorded over a period of time for nucleus
pressure, applied load, and peripherial strain against time. The
results show that for normal discs, pressures in the nucleus are
viscoelastic in nature with the applied compressive load.
Mechanical strains which develop around the periphery of the
vertebral body are also viscoelastic with the applied compressive
load. Applied compressive load against time also shows viscoelastic
behavior. However, annulus does not respond viscoelastically with
the applied load. It showed a linear response to compressive loading.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: This paper presents the speed regulation scheme of a small brushless dc motor (BLDC motor) with trapezoidal back-emf consideration. The proposed control strategy uses the proportional controller in which the proportional gain, kp, is appropriately adjusted by using genetic algorithms. As a result, the proportional control can perform well in order to compensate the BLDC motor with load disturbance. This confirms that the proposed speed regulation scheme gives satisfactory results.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: With the increasing number of on-chip components and the critical requirement for processing power, Chip Multiprocessor (CMP) has gained wide acceptance in both academia and industry during the last decade. However, the conventional bus-based onchip communication schemes suffer from very high communication delay and low scalability in large scale systems. Network-on-Chip (NoC) has been proposed to solve the bottleneck of parallel onchip communications by applying different network topologies which separate the communication phase from the computation phase. Observing that the memory bandwidth of the communication between on-chip components and off-chip memory has become a critical problem even in NoC based systems, in this paper, we propose a novel 3D NoC with on-chip Dynamic Random Access Memory (DRAM) in which different layers are dedicated to different functionalities such as processors, cache or memory. Results show that, by using our proposed architecture, average link utilization has reduced by 10.25% for SPLASH-2 workloads. Our proposed design costs 1.12% less execution cycles than the traditional design on average.
Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: This paper presents a portable robot that is to use for
welding process in shipbuilding yard. It has six degree of freedom and
3kg payload capability. Its weight is 21.5kg so that human workers can
carry it to the work place. Its body mainly made of magnesium alloy
and aluminum alloy for few parts that require high strength. Since the
distance between robot and controller should be 50m at most, the robot
controller controls the robot through EtherCAT. RTX and KPA are
used for real time EtherCAT control on Windows XP. The
performance of the developed robot was satisfactory, in welding of U
type cell in shipbuilding yard.
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: Nowadays there are lots of applications of power and
free conveyors in logistics. They are the most frequently used
conveyor systems worldwide. Overhead conveyor technologies like
power and free systems are used in the most intra-logistics
applications in trade and industry. The automotive, food, beverage
and textile industry as well as aeronautic catering or engineering are
among the applications. Power and free systems employ different
manufacturing intervals in manufacturing as well as in production as
temporary store and buffer. Depending on the application area, power
and free conveyors are equipped with target controls enabling
complex distribution-and sorting tasks. This article introduces a new
power and free conveyor design in intra-logistics and explains its
components. According to the explanation of the components, a
model is created by means of their technical characteristics. Through
the CAD software, the model is visualized. After that, the static
analysis is evaluated. This analysis helps the calculation of the
mandatory state of structures under force action. This powerful model
helps companies achieve lower development costs as well as quicker
market maturity.
Abstract: This paper proposes an investment cost recovery
based efficient and fast sequential optimization approach to optimal
allocation of thyristor controlled series compensator (TCSC) in
competitive power market. The optimization technique has been used
with an objective to maximizing the social welfare and minimizing
the device installation cost by suitable location and rating of TCSC in
the system. The effectiveness of proposed approach for location of
TCSC has been compared with some existing methods of TCSC
placement, in terms of its impact on social welfare, TCSC investment
recovery and optimal generation as well as load patterns. The results
have been obtained on modified IEEE 14-bus system.