Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: Recently, grid computing has been widely focused on
the science, industry, and business fields, which are required a vast
amount of computing. Grid computing is to provide the environment
that many nodes (i.e., many computers) are connected with each
other through a local/global network and it is available for many
users. In the environment, to achieve data processing among nodes
for any applications, each node executes mutual authentication by
using certificates which published from the Certificate Authority
(for short, CA). However, if a failure or fault has occurred in the
CA, any new certificates cannot be published from the CA. As
a result, a new node cannot participate in the gird environment.
In this paper, an off-the-shelf scheme for dependable grid systems
using virtualization techniques is proposed and its implementation is
verified. The proposed approach using the virtualization techniques
is to restart an application, e.g., the CA, if it has failed. The system
can tolerate a failure or fault if it has occurred in the CA. Since
the proposed scheme is implemented at the application level easily,
the cost of its implementation by the system builder hardly takes
compared it with other methods. Simulation results show that the
CA in the system can recover from its failure or fault.
Abstract: The objective of the research was to study of foot
anthropometry of children aged 7-12 years in the South of Thailand Thirty-three dimensions were measured on 305 male and 295 female
subjects with 3 age ranges (7-12 years old). The instrumentation consists of four types of anthropometer, digital vernier caliper, digital
height gauge and measuring tape. The mean values and standard
deviations of average age, height, and weight of the male subjects were 9.52(±1.70) years, 137.80(±11.55) cm, and 37.57(±11.65) kg.
Female average age, height, and weight subjects were 9.53(±1.70) years, 137.88(±11.55) cm, and 34.90(±11.57) kg respectively. The
comparison of the 33 comparison measured anthropometric. Between
male and female subjects were sexual differences in size on women in almost all areas of significance (p
Abstract: This paper deals principally with the socio-economic impact on the local Iban community in Mukah Division, Sarawak; with the commencement of the open-cut coal mining industry since 2003. To-date there are no actual studies being carried out by either the public or private sector to truly analyze how the Iban community is coping with the advent of a large influx of cash into their society. The Iban community has traditionally been practicing shifting cultivation and farming of domesticated animals; with a portion of the younger generation working as laborers and professional. This paper represents the views and observations of the author supported by some statistical facts extracted from published articles and non-published reports. The paper deals primarily in the following areas: • Background of the coal mining industry in Mukah Division, Sarawak; • Benefits of the coal mining industry towards the Iban community; • Issues / Problems arise in the Iban community because of the presence of the coal mining industry; and • Possible actions that need to be taken to overcome these issues/ problems.
Abstract: In the past decade, artificial neural networks (ANNs)
have been regarded as an instrument for problem-solving and
decision-making; indeed, they have already done with a substantial
efficiency and effectiveness improvement in industries and businesses.
In this paper, the Back-Propagation neural Networks (BPNs) will be
modulated to demonstrate the performance of the collaborative
forecasting (CF) function of a Collaborative Planning, Forecasting and
Replenishment (CPFR®) system. CPFR functions the balance between
the sufficient product supply and the necessary customer demand in a
Supply and Demand Chain (SDC). Several classical standard BPN will
be grouped, collaborated and exploited for the easy implementation of
the proposed modular ANN framework based on the topology of a
SDC. Each individual BPN is applied as a modular tool to perform the
task of forecasting SKUs (Stock-Keeping Units) levels that are
managed and supervised at a POS (point of sale), a wholesaler, and a
manufacturer in an SDC. The proposed modular BPN-based CF
system will be exemplified and experimentally verified using lots of
datasets of the simulated SDC. The experimental results showed that a
complex CF problem can be divided into a group of simpler
sub-problems based on the single independent trading partners
distributed over SDC, and its SKU forecasting accuracy was satisfied
when the system forecasted values compared to the original simulated
SDC data. The primary task of implementing an autonomous CF
involves the study of supervised ANN learning methodology which
aims at making “knowledgeable" decision for the best SKU sales plan
and stocks management.
Abstract: Optical 3D measurement of objects is meaningful in
numerous industrial applications. In various cases shape acquisition
of weak textured objects is essential. Examples are repetition parts
made of plastic or ceramic such as housing parts or ceramic bottles as
well as agricultural products like tubers. These parts are often
conveyed in a wobbling way during the automated optical inspection.
Thus, conventional 3D shape acquisition methods like laser scanning
might fail. In this paper, a novel approach for acquiring 3D shape of
weak textured and moving objects is presented. To facilitate such
measurements an active stereo vision system with structured light is
proposed. The system consists of multiple camera pairs and auxiliary
laser pattern generators. It performs the shape acquisition within one
shot and is beneficial for rapid inspection tasks. An experimental
setup including hardware and software has been developed and
implemented.
Abstract: Nagaland, the 16th state of India in order of
statehood, is situated between 25° 6' and 27° 4' latitude north and
between 93º 20' E and 95º 15' E longitude of equator in the North
Eastern part of the India. Endowed with varied topography, soil and
agro climatic conditions it is known for its potentiality to grow all
most all kinds of horticultural crops. Pineapple being grown since
long organically by default is one of the most promising crops of the
state with emphasis being laid for commercialization by the
government of Nagaland. In light of commercialization, globalization
and scope of setting small-scale industries, a research study was
undertaken to examine the socio-economic and personal
characteristics, entrepreneurial characteristics and attitude of the
pineapple growers towards improved package of practices of
pineapple cultivation. The study was conducted in Medziphema
block of Dimapur district of the Nagaland state of India following ex
post facto research design. Ninety pineapple growers were selected
from four different villages of Medziphema block based on
proportionate random selection procedure. Findings of the study
revealed that majority of the respondents had medium level of
entrepreneurial characteristics in terms of knowledge level, risk
orientation, self confidence, management orientation, farm decision
making ability and leadership ability and most of them had
favourable attitude towards improved package of practices of
pineapple cultivation. The variables age, education, farm size, risk
orientation, management orientation and sources of information
utilized were found important to influence the attitude of the
respondents. The study revealed that favourable attitude and
entrepreneurial characteristics of the pineapple cultivators might be
harnessed for increased production of pineapple in the state thereby
bringing socio economic upliftment of the marginal and small-scale
farmers.
Abstract: Academia-industry relationship is not like that of
technology donator-acceptor, but is of interactive and collaborative
nature, acknowledging and ensuring mutual respect for each other-s
role and contributions with an eye to attaining the true purpose of
such relationships, namely, bringing about research-outcome
synergy. Indeed, academia-industry interactions are a system that
requires active and collaborative participations of all the
stakeholders.
This paper examines various issues associated with academic
institutions and industry collaboration with special attention to the
nature of resources and potentialities of stakeholders in the context of
knowledge management. This paper also explores the barriers of
academia-industry interaction. It identifies potential areas where
industry-s participation with academia would be most effective for
synergism. Lastly, this paper proposes an integrated model of several
new collaborative approaches that are possible, mainly in the Indian
scenario to strengthen academia-industry interface.
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The study extends the knowledge on
innovativeness theory by using a multi-dimensional contructs to
conceptualize the innovativeness of public listed housing developers
in Malaysia where all this while most studies focused on single
dimensional construct of innovativeness. The paper ends by
providing some explanations for the results.
Abstract: This study is concerned with the investigation of the
suitability of several empirical and semi-empirical drying models
available in the literature to define drying behavior of viscose yarn
bobbins. For this purpose, firstly, experimental drying behaviour of
viscose bobbins was determined on an experimental dryer setup
which was designed and manufactured based on hot-air bobbin
dryers used in textile industry. Afterwards, drying models considered
were fitted to the experimentally obtained moisture ratios. Drying
parameters were drying temperature and bobbin diameter. The fit
was performed by selecting the values for constants in the models in
such a way that these values make the sum of the squared differences
between the experimental and the model results for moisture ratio
minimum. Suitability of fitting was specified as comparing the
correlation coefficient, standard error and mean square deviation.
The results show that the most appropriate model in describing the
drying curves of viscose bobbins is the Page model.
Abstract: The study was performed to evaluate the effect of Sgirdling,
fruit thinning plus bagging with 2,4-D application, fruit
thinning plus bagging on growth and quality of wax apple fruit.
Girdling was applied three week before flowering. The 2,4-D was
sprayed at the small bud and petal fall stage. The effect of all
treatments on fruit growth was measured weekly. The physical and
biochemical quality characteristics of the fruits were recorded. The
results showed that no significant effect on number of bud among
treatments. S-girdling, 2,4-D application produced the lowest bud
drop, fruit drop compared to untreated control. Moreover, S-girdling
enhanced faster fruit growth producing the best final fruit length and
diameter than the control treatment. It was also observed that Sgirdling
greatly increased fruit set, fruit weight as well as total
soluble solid, reduced fruit crack, and titratable acidity. In
conclusion, S-girdling had a distinctive and significant effect on most
of the fruit quality characteristics assessed. Application 2,4-D was
also recommended as the industry norm to increase fruit set, and fruit
quality in wax apple.
Abstract: The eco-efficient use of “waste" makes sense from
economic, social, and environmental perspectives. By efficiency diverting “waste" products back into useful and/or profitable inputs,
industries and entire societies can reap the benefits of improved financial profit, decreased environmental degradation, and overall
well-being of humanity.
In this project, several material flows at
Company Limited were investigated. Principles of "industrial ecology" were applied to improve the management of waste rubbers that are used in the jewelry manufacturing process. complete this project, a brief engineering analysis stream, and investigated eco-efficient principles for more efficient
handling of the materials and wastes were conducted, and the result were used to propose implementation strategies.
Abstract: As in today's semiconductor industries test costs can make up to 50 percent of the total production costs, an efficient test error detection becomes more and more important. In this paper, we present a new machine learning approach to test error detection that should provide a faster recognition of test system faults as well as an improved test error recall. The key idea is to learn a classifier ensemble, detecting typical test error patterns in wafer test results immediately after finishing these tests. Since test error detection has not yet been discussed in the machine learning community, we define central problem-relevant terms and provide an analysis of important domain properties. Finally, we present comparative studies reflecting the failure detection performance of three individual classifiers and three ensemble methods based upon them. As base classifiers we chose a decision tree learner, a support vector machine and a Bayesian network, while the compared ensemble methods were simple and weighted majority vote as well as stacking. For the evaluation, we used cross validation and a specially designed practical simulation. By implementing our approach in a semiconductor test department for the observation of two products, we proofed its practical applicability.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: During the last couple of years, the degree of dependence on IT systems has reached a dimension nobody imagined to be possible 10 years ago. The increased usage of mobile devices (e.g., smart phones), wireless sensor networks and embedded devices (Internet of Things) are only some examples of the dependency of modern societies on cyber space. At the same time, the complexity of IT applications, e.g., because of the increasing use of cloud computing, is rising continuously. Along with this, the threats to IT security have increased both quantitatively and qualitatively, as recent examples like STUXNET or the supposed cyber attack on Illinois water system are proofing impressively. Once isolated control systems are nowadays often publicly available - a fact that has never been intended by the developers. Threats to IT systems don’t care about areas of responsibility. Especially with regard to Cyber Warfare, IT threats are no longer limited to company or industry boundaries, administrative jurisdictions or state boundaries. One of the important countermeasures is increased cooperation among the participants especially in the field of Cyber Defence. Besides political and legal challenges, there are technical ones as well. A better, at least partially automated exchange of information is essential to (i) enable sophisticated situational awareness and to (ii) counter the attacker in a coordinated way. Therefore, this publication performs an evaluation of state of the art Intrusion Detection Message Exchange protocols in order to guarantee a secure information exchange between different entities.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: Since the late 1980s, the new phenomena of 'employment subcentres' or 'polycentricity' has appeared in the metropolises of North American and Western Europe and it has been an interesting topic for academics and researchers. This paper specifically uses one case study-Guangzhou to explore the development and the mechanism of employment subcentres and polycentricity in Chinese metropolises by spatial analysis method on the basis of the first economic census data. In conclusion, the paper regards that the employment subcentres and polycentricity has existed in Chinese metropolises. And that, the mechanism of them is mainly from the secondary industry instead of the tertiary industry in North American and Western Europe
Abstract: In this study, aerobic digestion of tannery industry
wastewater was carried out using mixed culture obtained from
common effluent treatment plant treating tannery wastewater. The
effect of pH, temperature, inoculum concentration, agitation speed
and initial substrate concentration on the reduction of organic matters
were found. The optimum conditions for COD reduction was found
to be pH - 7 (60%), temperature - 30ÔùªC (61%), inoculum
concentration - 2% (61%), agitation speed - 150rpm (65%) and initial
substrate concentration - 1560 mg COD/L (74%). Kinetics studies
were carried by using Monod model, First order, Diffusional model
and Singh model. From the results it was found that the Monod
model suits well for the degradation of tannery wastewater using
mixed microbial consortium.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.