Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: Dextran is a D-glucose polymer which is produced by
Leuconostoc mesenteroides grown in a sucrose-rich media. The
organism was obtained from the Persian Type Culture Collection
(PTCC) and was transferred in MRS broth medium at 30°C and pH
6.8 for 24 h. After preparation of inoculums, organisms were
inoculated into five liquid fermentation media containing either
molasses or cheese whey or different combinations of cheese whey
and molasses. After certain fermentation period, the produced
dextran was separated and dried. Dextran yield was calculated and
significant differences in different media were observed.
Furthermore, FT-IR analysis was performed and the results showed
that there were no significant differences in the produced dextran
structures.
Abstract: Higher productivity and less cost in the ship
manufacturing process are required to maintain the international
competitiveness of morden manufacturing industries. In shipbuilding,
however, the Engineering To Order (ETO) production method and
production process is very difficult. Thus, designs change frequently.
In accordance with production, planning should be set up according
to scene changes. Therefore, fixed production planning is very
difficult. Thus, a scheduler must first make sketchy plans, then
change the plans based on the work progress and modifications.
Thus, data sharing in a shipbuilding block assembly shop is very
important. In this paper, we proposed to scheduling method
applicable to the shipbuilding industry and decision making support
system through web based visualization system.
Abstract: This paper discusses the performance modeling and availability analysis of Yarn Dyeing System of a Textile Industry. The Textile Industry is a complex and repairable engineering system. Yarn Dyeing System of Textile Industry consists of five subsystems arranged in series configuration. For performance modeling and analysis of availability, a performance evaluating model has been developed with the help of mathematical formulation based on Markov-Birth-Death Process. The differential equations have been developed on the basis of Probabilistic Approach using a Transition Diagram. These equations have further been solved using normalizing condition in order to develop the steady state availability, a performance measure of the system concerned. The system performance has been further analyzed with the help of decision matrices. These matrices provide various availability levels for different combinations of failure and repair rates for various subsystems. The findings of this paper are therefore, considered to be useful for the analysis of availability and determination of the best possible maintenance strategies which can be implemented in future to enhance the system performance.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: This study proposes a multi-response surface
optimization problem (MRSOP) for determining the proper choices
of a process parameter design (PPD) decision problem in a noisy
environment of a grease position process in an electronic industry.
The proposed models attempts to maximize dual process responses
on the mean of parts between failure on left and right processes. The
conventional modified simplex method and its hybridization of the
stochastic operator from the hunting search algorithm are applied to
determine the proper levels of controllable design parameters
affecting the quality performances. A numerical example
demonstrates the feasibility of applying the proposed model to the
PPD problem via two iterative methods. Its advantages are also
discussed. Numerical results demonstrate that the hybridization is
superior to the use of the conventional method. In this study, the
mean of parts between failure on left and right lines improve by
39.51%, approximately. All experimental data presented in this
research have been normalized to disguise actual performance
measures as raw data are considered to be confidential.
Abstract: Ranong province has the best kaolin, and it is the most
useful of all the clay types used in ceramic making. Until recently,
there has been only one community business making ceramics in
Ranong province. And this business could not build the mix of body
and glaze from their raw material without assistance. Considering
these problems, this research is aimed to test the composition of
ceramic body and glaze which suit. Kaolin from Ranong is the raw
material which these search focuses on. All other raw materials use in
the investigation will come from southern Thailand, kaolin and
limestone from Ranong province, ball clay from Surat Thani
province, white sand from Songkhla province, and feldspar from
Nakhon Si Thammarat province. Results can be used to develop the
efficiency of industrial production which in return will enhance the
business process.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.
Abstract: This paper reports the three-phase (gas + liquid +
hydrate) equilibrium pressure versus temperature data for a (O3 + O2 +
CO2 + H2O) system for developing the hydrate-based technology to
preserve ozone, a chemically unstable substance, for various
industrial, medical and consumer uses. These data cover the
temperature range from 272 K to 277 K, corresponding to pressures
from 1.6 MPa to 3.1 MPa, for each of the three different (O3 +
O2)-to-CO2 or O2-to-CO2 molar ratios in the gas phase, which are
approximately 4 : 6, 5 : 5, respectively. The mole fraction of ozone in
the gas phase was ~0.03 , which are the densest ozone fraction to
artificially form O3 containing hydrate ever reported in the literature.
Based on these data, the formation of hydrate containing
high-concentration ozone, as high as 1 mass %, will be expected.
Abstract: Construction projects generally take place in
uncontrolled and dynamic environments where construction waste is
a serious environmental problem in many large cities. The total
amount of waste and carbon dioxide emissions from transportation
vehicles are still out of control due to increasing construction
projects, massive urban development projects and the lack of
effective tools for minimizing adverse environmental impacts in
construction. This research is about utilization of the integrated
applications of automated advanced tracking and data storage
technologies in the area of environmental management to monitor
and control adverse environmental impacts such as construction
waste and carbon dioxide emissions. Radio Frequency Identification
(RFID) integrated with the Global Position System (GPS) provides
an opportunity to uniquely identify materials, components, and
equipments and to locate and track them using minimal or no worker
input. The transmission of data to the central database will be carried
out with the help of Global System for Mobile Communications
(GSM).
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: Metallic micro parts are playing an important role in micro-fabrication industry. Recently, we have demonstrated a new deformation mechanism for micro-formability of polycrystalline materials. Different depressed micro-features smaller than the grain size have been successfully fabricated on 6061 aluminum alloy (AA6061) substrates with good fidelity. To further verify this proposed deformation mechanism that grain size is not a limiting factor, we demonstrate here that in addition of depressed features, protruded micro-features on a polycrystalline substrate can similarly be fabricated.
Abstract: Nowadays, under developed countries for progress in
science and technology and decreasing the technologic gap with
developed countries, increasing the capacities and technology
transfer from developed countries. To remain competitive, industry is
continually searching for new methods to evolve their products.
Business model is one of the latest buzzwords in the Internet and
electronic business world. To be successful, organizations must look
into the needs and wants of their customers. This research attempts to
identify a specific feature of the company with a strong competitive
advantage by analyzing the cause of Customer satisfaction. Due to
the rapid development of knowledge and information technology,
business environments have become much more complicated.
Information technology can help a firm aiming to gain a competitive
advantage. This study explores the role and effect of Information
Communication Technology in Business Models and Customer
satisfaction on firms and also relationships between ICTs and
Outsourcing strategic.
Abstract: In this work, bending fatigue life of notched
specimens with various notch geometries and dimensions is
investigated by experiment and Manson-Caffin theoretical method. In
this theoretical method, fatigue life of notched specimens is
calculated using the fatigue life obtained from the experiments for
plain specimens (without notch). Three notch geometries including
∪-shape, ∨-shape and C -shape notches are considered in this
investigation. The experiments are conducted on a rotary bending
Moore machine. The specimens are made of a low carbon steel alloy,
which has wide application in industry. The stress- life curves are
captured for all notched specimen by experiment. The results indicate
that Manson-Caffin analytical method cannot adequately predict
the fatigue life of notched specimen. However, it seems that the
difference between the experiments and Manson-Caffin predictions
can be compensated by a proportional factor.
Abstract: The paper is intended to declare and apply ethics, i. e.
moral principles, rules in marketing environment. Ethical behavior of
selected pharmaceutical companies in the Slovak Republic is the
object of our research. The aim of our research is to determine
perception of ethical behavior of the pharmaceutical industry in
Slovakia by the medicine representatives in comparison with the
assessment of doctors and patients. The experimental sample
included 90 participants who were divided into three groups:
medicine representatives of the pharmaceutical companies (N=30),
doctors (N=30) and patients (N=30). The research method was a
Questionnaire of ethical behavior, created by us, that describes
individual areas included in the Code of ethics of the pharmaceutical
industry in Slovakia. The results showed influence of professional
status on ethical behavior perception, not gender. Higher perception
was indicated at patients rather than doctors and medicine
representatives.
Abstract: The purpose of this study is to analyze Green IT industry in major developed countries and to suggest overall directions for IT-Energy convergence industry. Recently, IT industry is pointed out as a problem such as environmental pollution, energy exhaustion, and high energy consumption. Therefore, Green IT gets focused which concerns as solution of these problems. However, since it is a beginning stage of this convergence area, there are only a few studies of IT-Energy convergence industry. According to this, this study examined the major developed countries in terms of institution arrangements, resources, markets and companies based on Van de Ven(1999)'s social system framework that shows relationship among key components of industrial infrastructure. Subsequently, the direction of the future study of convergence on IT and Energy industry is proposed.
Abstract: Sandwich panels are widely used in the construction
industry for their ease of assembly, light weight and efficient thermal
performance. They are composed of two RC thin outer layers
separated by an insulating inner layer. In this research the inner
insulating layer is made of lightweight Autoclaved Aerated Concrete
(AAC) blocks which has good thermal insulation properties and yet
possess reasonable mechanical strength. The shear strength of the
AAC infill is relied upon to replace the traditionally used insulating
foam and to provide the shear capacity of the panel. A
comprehensive experimental program was conducted on full scale
sandwich panels subjected to bending. In this paper, detailed
numerical modeling of the tested sandwich panels is reported. Nonlinear
3-D finite element modeling of the composite action of the
sandwich panel is developed using ANSYS. Solid elements with
different crashing and cracking capabilities and different constitutive
laws were selected for the concrete and the AAC. Contact interface
elements are used in this research to adequately model the shear
transfer at the interface between the different layers. The numerical
results showed good correlation with the experimental ones
indicating the adequacy of the model in estimating the loading
capacity of panels.
Abstract: Failure modes and effects analysis (FMEA) is an effective technique for preventing potential problems and actions needed to error cause removal. On the other hand, the oil producing companies paly a critical role in the oil industry of Iran as a developing country out of which, Sepahan Oil Co. has a considerable contribution. The aim of this research is to show how FMEA could be applied and improve the quality of products at Sepahan Oil Co. For this purpose, the four liter production line of the company has been selected for investigation. The findings imply that the application of FMEA has reduced the scraps from 50000 ppm to 5000 ppm and has resulted in a 0.92 percent decrease of the oil waste.
Abstract: Information technology managers nowadays are
facing with tremendous pressure to plan, implement, and adopt new
technology solution due to the rapidity of technology changes.
Resulted from a lack of study that have been done in this topic, the
aim of this paper is to provide a comparison review on current tools
that are currently being used in order to respond to technological
changes. The study is based on extensive literature review of
published works with majority of them are ranging from 2000 to the
first part of 2011. The works were gathered from journals, books,
and other information sources available on the Web. Findings show
that, each tools has different focus and none of the tools are
providing a framework in holistic view, which should include
technical, people, process, and business environment aspect. Hence,
this result provides potential information about current available
tools that IT managers could use to manage changes in technology.
Further, the result reveals a research gap in the area where the
industries a short of such framework.