Abstract: Huge losses in apple production are caused by pathogens that cannot be seen shortly after harvest. After-harvest thermotherapy treatments can considerably improve control of storage diseases on apples and become an alternative to chemical pesticides. In the years 2010-2012 carried out research in this area. Apples of 'Topaz' cultivar were harvested at optimal maturity time for long storage and subject to water bath treatment at 45, 50, 52, 55°C for 60, 120, 180 and 240 seconds. The control was untreated fruits. After 12 and 24 weeks and during so called simulated trade turnover the fruits were checked for their condition and the originators of diseases were determined by using the standard phytopathological methods. The most common originator of 'Topaz' apple infection during storage were the fungi of genus Gloeosporium. In this paper it was proven that for effective protection of 'Topaz' apples against diseases, thermotherapy by using water treatments at temperature range of 50-52°C is quite sufficient.
Abstract: The soil ecology of the organic and mineral soil layers
of laurel-leaved and Cryptomeria japonica forest in the Kasuga-yama
Hill Primeval Forest (Nara, Japan) was assessed. The number of
bacteria obtained by the dilution plate count method was less than
0.05% of those counted by the direct microscopic count. We therefore
found that forest soil contains large numbers of non-culturable
bacteria compared with agricultural soils. The numbers of bacteria and
fungi obtained by both the dilution plate count and the direct
microscopic count were larger in the deeper horizons (F and H) of the
organic layer than in the mineral soil layer. This suggests that active
microbial metabolism takes place in the organic layer. The numbers of
bacteria and the length of fungal hyphae obtained by the direct count
method were greater in the H horizon than in the F horizon. The direct
microscopic count revealed numerous non-culturable bacteria and
fungi in the soil. The ratio of fungal to bacterial biomass was lower in
the laurel-leaved forest soil. The fungal biomass was therefore
relatively low in the laurel-leaved forest soil due to differences in
forest vegetation.
Abstract: Rise/span ratio has been mentioned as one of the
reasons which contribute to the lower buckling load as compared to
the Classical theory buckling load but this ratio has not been quantified
in the equation. The purpose of this study was to determine a more
realistic buckling load by quantifying the effect of the rise/span ratio
because experiments have shown that the Classical theory
overestimates the load. The buckling load equation was derived based
on the theorem of work done and strain energy. Thereafter, finite
element modeling and simulation using ABAQUS was done to
determine the variables that determine the constant in the derived
equation. The rise/span was found to be the determining factor of the
constant in the buckling load equation. The derived buckling load
correlates closely to the load obtained from experiments.
Abstract: This paper presents a novel algorithm for path planning of mobile robots in known 3D environments using Binary Integer Programming (BIP). In this approach the problem of path planning is formulated as a BIP with variables taken from 3D Delaunay Triangulation of the Free Configuration Space and solved to obtain an optimal channel made of connected tetrahedrons. The 3D channel is then partitioned into convex fragments which are used to build safe and short paths within from Start to Goal. The algorithm is simple, complete, does not suffer from local minima, and is applicable to different workspaces with convex and concave polyhedral obstacles. The noticeable feature of this algorithm is that it is simply extendable to n-D Configuration spaces.
Abstract: Since supply chains highly impact the financial
performance of companies, it is important to optimize and analyze
their Key Performance Indicators (KPI). The synergistic combination
of Particle Swarm Optimization (PSO) and Monte Carlo simulation is
applied to determine the optimal reorder point of warehouses in
supply chains. The goal of the optimization is the minimization of the
objective function calculated as the linear combination of holding and
order costs. The required values of service levels of the warehouses
represent non-linear constraints in the PSO. The results illustrate that
the developed stochastic simulator and optimization tool is flexible
enough to handle complex situations.
Abstract: This paper presents the modeling of a MEMS based accelerometer in order to detect the presence of a wheel flat in the railway vehicle. A haversine wheel flat is assigned to one wheel of a 5 DOF pitch plane vehicle model, which is coupled to a 3 layer track model. Based on the simulated acceleration response obtained from the vehicle-track model, an accelerometer is designed that meets all the requirements to detect the presence of a wheel flat. The proposed accelerometer can survive in a dynamic shocking environment with acceleration up to ±150g. The parameters of the accelerometer are calculated in order to achieve the required specifications using lumped element approximation and the results are used for initial design layout. A finite element analysis code (COMSOL) is used to perform simulations of the accelerometer under various operating conditions and to determine the optimum configuration. The simulated results are found within about 2% of the calculated values, which indicates the validity of lumped element approach. The stability of the accelerometer is also determined in the desired range of operation including the condition under shock.
Abstract: Many works have been carried out to compare the
efficiency of several goodness of fit procedures for identifying
whether or not a particular distribution could adequately explain a
data set. In this paper a study is conducted to investigate the power
of several goodness of fit tests such as Kolmogorov Smirnov (KS),
Anderson-Darling(AD), Cramer- von- Mises (CV) and a proposed
modification of Kolmogorov-Smirnov goodness of fit test which
incorporates a variance stabilizing transformation (FKS). The
performances of these selected tests are studied under simple
random sampling (SRS) and Ranked Set Sampling (RSS). This
study shows that, in general, the Anderson-Darling (AD) test
performs better than other GOF tests. However, there are some
cases where the proposed test can perform as equally good as the
AD test.
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: Integrated Total Quality Management (TQM) with
Lean Manufacturing (LM) is a system comprises of TQM with LM
principles and is associated with financial and nonfinancial
performance measurement indicators. The ultimate goal of this
system is to focus on achieving total customer satisfaction by
removing eight wastes available in any process in an organization.
A survey questionnaire was developed and distributed to 30 highly
active automotive vendors in Malaysia and analyzed by PASW
Statistics 18. It was found out that these vendors have been
practicing and measuring the effectiveness TQM and LM
implementation. More involvement of all Malaysian automotive
vendors will represent the exact status of current Malaysian
automotive industry in implementing TQM and LM and can
determine whether the industry is ready for integrated TQM and
LM system. This is the first study that combined 4 awards
practices, ISO/TS16949, Toyota Production System and
SAEJ4000.
Abstract: Extensive information is required within a R&D environment,
and a considerable amount of time and efforts are being
spent on finding the necessary information. An adaptive information
providing system would be beneficial to the environment, and a
conceptual model of the resources, people and context is mandatory
for developing such applications. In this paper, an information model
on various contexts and resources is proposed which provides the
possibility of effective applications for use in adaptive information
systems within a R&D project and meeting environment.
Abstract: In this paper, Novel method, Particle Swarm Optimization (PSO) algorithm, based technique is proposed to estimate and analyze the steady state performance of self-excited induction generator (SEIG). In this novel method the tedious job of deriving the complex coefficients of a polynomial equation and solving it, as in previous methods, is not required. By comparing the simulation results obtained by the proposed method with those obtained by the well known mathematical methods, a good agreement between these results is obtained. The comparison validates the effectiveness of the proposed technique.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Information hiding for authenticating and verifying the content integrity of the multimedia has been exploited extensively in the last decade. We propose the idea of using genetic algorithm and non-deterministic dependence by involving the un-watermarkable coefficients for digital image authentication. Genetic algorithm is used to intelligently select coefficients for watermarking in a DCT based image authentication scheme, which implicitly watermark all the un-watermarkable coefficients also, in order to thwart different attacks. Experimental results show that such intelligent selection results in improvement of imperceptibility of the watermarked image, and implicit watermarking of all the coefficients improves security against attacks such as cover-up, vector quantization and transplantation.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: This research is designed for helping a WAPbased mobile phone-s user in order to analyze of logistics in the traffic area by applying and designing the accessible processes from mobile user to server databases. The research-s design comprises Mysql 4.1.8-nt database system for being the server which there are three sub-databases, traffic light – times of intersections in periods of the day, distances on the road of area-blocks where are divided from the main sample-area and speeds of sample vehicles (motorcycle, personal car and truck) in periods of the day. For interconnections between the server and user, PHP is used to calculate distances and travelling times from the beginning point to destination, meanwhile XHTML applied for receiving, sending and displaying data from PHP to user-s mobile. In this research, the main sample-area is focused at the Huakwang-Ratchada-s area, Bangkok, Thailand where usually the congested point and 6.25 km2 surrounding area which are split into 25 blocks, 0.25 km2 for each. For simulating the results, the designed server-database and all communicating models of this research have been uploaded to www.utccengineering.com/m4tg and used the mobile phone which supports WAP 2.0 XHTML/HTML multimode browser for observing values and displayed pictures. According to simulated results, user can check the route-s pictures from the requiring point to destination along with analyzed consuming times when sample vehicles travel in various periods of the day.
Abstract: Quality costs are the costs associated with preventing,
finding, and correcting defective work. Since the main language of
corporate management is money, quality-related costs act as means of
communication between the staff of quality engineering departments
and the company managers. The objective of quality engineering is to
minimize the total quality cost across the life of product. Quality
costs provide a benchmark against which improvement can be
measured over time. It provides a rupee-based report on quality
improvement efforts. It is an effective tool to identify, prioritize and
select quality improvement projects. After reviewing through the
literature it was noticed that a simplified methodology for data
collection of quality cost in a manufacturing industry was required.
The quantified standard methodology is proposed for collecting data
of various elements of quality cost categories for manufacturing
industry. Also in the light of research carried out so far, it is felt
necessary to standardise cost elements in each of the prevention,
appraisal, internal failure and external failure costs. . Here an attempt
is made to standardise the various cost elements applicable to
manufacturing industry and data is collected by using the proposed
quantified methodology. This paper discusses the case study carried
in luggage manufacturing industry.
Abstract: Nowadays social media are important tools for web
resource discovery. The performance and capabilities of web searches
are vital, especially search results from social research paper
bookmarking. This paper proposes a new algorithm for ranking
method that is a combination of similarity ranking with paper posted
time or CSTRank. The paper posted time is static ranking for
improving search results. For this particular study, the paper posted
time is combined with similarity ranking to produce a better ranking
than other methods such as similarity ranking or SimRank. The
retrieval performance of combination rankings is evaluated using
mean values of NDCG. The evaluation in the experiments implies
that the chosen CSTRank ranking by using weight score at ratio 90:10
can improve the efficiency of research paper searching on social
bookmarking websites.
Abstract: Electronic Systems are the core of everyday lives.
They form an integral part in financial networks, mass transit,
telephone systems, power plants and personal computers. Electronic
systems are increasingly based on complex VLSI (Very Large Scale
Integration) integrated circuits. Initial electronic design automation is
concerned with the design and production of VLSI systems. The next
important step in creating a VLSI circuit is Physical Design. The
input to the physical design is a logical representation of the system
under design. The output of this step is the layout of a physical
package that optimally or near optimally realizes the logical
representation. Physical design problems are combinatorial in nature
and of large problem sizes. Darwin observed that, as variations are
introduced into a population with each new generation, the less-fit
individuals tend to extinct in the competition of basic necessities.
This survival of fittest principle leads to evolution in species. The
objective of the Genetic Algorithms (GA) is to find an optimal
solution to a problem .Since GA-s are heuristic procedures that can
function as optimizers, they are not guaranteed to find the optimum,
but are able to find acceptable solutions for a wide range of
problems. This survey paper aims at a study on Efficient Algorithms
for VLSI Physical design and observes the common traits of the
superior contributions.
Abstract: Functional imaging procedures for the non-invasive assessment of tissue microcirculation are highly requested, but require a mathematical approach describing the trans- and intercapillary passage of tracer particles. Up to now, two theoretical, for the moment different concepts have been established for tracer kinetic modeling of contrast agent transport in tissues: pharmacokinetic compartment models, which are usually written as coupled differential equations, and the indicator dilution theory, which can be generalized in accordance with the theory of lineartime- invariant (LTI) systems by using a convolution approach. Based on mathematical considerations, it can be shown that also in the case of an open two-compartment model well-known from functional imaging, the concentration-time course in tissue is given by a convolution, which allows a separation of the arterial input function from a system function being the impulse response function, summarizing the available information on tissue microcirculation. Due to this reason, it is possible to integrate the open two-compartment model into the system-theoretic concept of indicator dilution theory (IDT) and thus results known from IDT remain valid for the compartment approach. According to the long number of applications of compartmental analysis, even for a more general context similar solutions of the so-called forward problem can already be found in the extensively available appropriate literature of the seventies and early eighties. Nevertheless, to this day, within the field of biomedical imaging – not from the mathematical point of view – there seems to be a trench between both approaches, which the author would like to get over by exemplary analysis of the well-known model.
Abstract: In this project electrical and optical properties of
BaZrO3 have been accomplished through the full-potential
linear augmented plane wave (FP-LAPW) by applying Wein2k
software. In this study band structure, density of state, gap energy,
refractive index and optical conduction have been studied. The results
of calculations show that BaZrO3 is an insulator with an indirect gap
in which 3.2 ev and studied refractive index equal 2.07. These results
are in accordance with the ones obtained in experimental researches.