Abstract: Higher order ΔΣ Modulator (DSM) is basically an
unstable system. The approximate conditions for stability cannot be
used for the design of a DSM for industrial applications where risk is
involved. The existing second order, single stage, single bit, unity
feedback gain , discrete DSM cannot be used for the normalized full
range (-1 to +1) of an input signal since the DSM becomes unstable
when the input signal is above ±0.55. The stability is also not
guaranteed for input signals of amplitude less than ±0.55. In the
present paper, the above mentioned second order DSM is modified
with input signal dependent forward path gain. The proposed DSM is
suitable for industrial applications where one needs the digital
representation of the analog input signal, during each sampling
period. The proposed DSM can operate almost for the full range of
input signals (-0.95 to +0.95) without causing instability, assuming
that the second integrator output should not exceed the circuit supply
voltage, ±15 Volts.
Abstract: It is difficult to study the effect of various variables on
cycle fitting through actual experiment. To overcome such difficulty,
the forward dynamics of a musculoskeletal model was applied to cycle
fitting in this study. The measured EMG data weres compared with the
muscle activities of the musculoskeletal model through forward
dynamics. EMG data were measured from five cyclists who do not
have musculoskeletal diseases during three minutes pedaling with a
constant load (150 W) and cadence (90 RPM). The muscles used for
the analysis were the Vastus Lateralis (VL), Tibialis Anterior (TA),
Bicep Femoris (BF), and Gastrocnemius Medial (GM). Person’s
correlation coefficients of the muscle activity patterns, the peak timing
of the maximum muscle activities, and the total muscle activities were
calculated and compared. BIKE3D model of AnyBody (Anybodytech,
Denmark) was used for the musculoskeletal model simulation. The
comparisons of the actual experiments with the simulation results
showed significant correlations in the muscle activity patterns (VL:
0.789, TA: 0.503, BF: 0.468, GM: 0.670). The peak timings of the
maximum muscle activities were distributed at particular phases. The
total muscle activities were compared with the normalized muscle
activities, and the comparison showed about 10% difference in the VL
(+10%), TA (+9.7%), and BF (+10%), excluding the GM (+29.4%).
Thus, it can be concluded that muscle activities of model &
experiment showed similar results. The results of this study indicated
that it was possible to apply the simulation of further improved
musculoskeletal model to cycle fitting.
Abstract: Artificial Neural Network (ANN) can be trained using
back propagation (BP). It is the most widely used algorithm for
supervised learning with multi-layered feed-forward networks.
Efficient learning by the BP algorithm is required for many practical
applications. The BP algorithm calculates the weight changes of
artificial neural networks, and a common approach is to use a twoterm
algorithm consisting of a learning rate (LR) and a momentum
factor (MF). The major drawbacks of the two-term BP learning
algorithm are the problems of local minima and slow convergence
speeds, which limit the scope for real-time applications. Recently the
addition of an extra term, called a proportional factor (PF), to the
two-term BP algorithm was proposed. The third increases the speed
of the BP algorithm. However, the PF term also reduces the
convergence of the BP algorithm, and criteria for evaluating
convergence are required to facilitate the application of the three
terms BP algorithm. Although these two seem to be closely related,
as described later, we summarize various improvements to overcome
the drawbacks. Here we compare the different methods of
convergence of the new three-term BP algorithm.
Abstract: The IEEE 802.22 working group aims to drive the
Digital Video Broadcasting-Terrestrial (DVB-T) bands for data
communication to the rural area without interfering the TV broadcast.
In this paper, we arrive at a closed-form expression for average
detection probability of Fusion center (FC) with multiple antenna
over the κ − μ fading channel model. We consider a centralized
cooperative multiple antenna network for reporting. The DVB-T
samples forwarded by the secondary user (SU) were combined using
Maximum ratio combiner at FC, an energy detection is performed
to make the decision. The fading effects of the channel degrades
the detection probability of the FC, a generalized independent and
identically distributed (IID) κ − μ and an additive white Gaussian
noise (AWGN) channel is considered for reporting and sensing
respectively. The proposed system performance is verified through
simulation results.
Abstract: Electricity spot prices are highly volatile under
optimal generation capacity scenarios due to factors such as nonstorability
of electricity, peak demand at certain periods, generator
outages, fuel uncertainty for renewable energy generators, huge
investments and time needed for generation capacity expansion etc.
As a result market participants are exposed to price and volume risk,
which has led to the development of risk management practices. This
paper provides an overview of risk management practices by market
participants in electricity markets using financial derivatives.
Abstract: Fuzzy inference method based approach to the
forming of modular intellectual system of assessment the quality of
communication services is proposed. Developed under this approach
the basic fuzzy estimation model takes into account the
recommendations of the International Telecommunication Union in
respect of the operation of packet switching networks based on IPprotocol.
To implement the main features and functions of the fuzzy
control system of quality telecommunication services it is used
multilayer feedforward neural network.
Abstract: Due to the importance of ports to trade and economic
development of the regions in which they are inserted, in recent
decades the number of studies devoted to this subject has increased.
Part of these studies considers the ports as business agglomerations
and focuses on port governance. This is an important approach since
the port performance is the result of activities performed by actors
belonging to the port-logistics chain, which need to be properly
coordinated. This coordination takes place through a port governance
model. Given this context, this study aims to analyze the governance
model of the port of Santos from the perspective of port customers.
To do this, a closed-ended questionnaire based on a conceptual model
that considers the key dimensions associated with port governance
was applied to the international freight forwarders that operate in the
port. The results show the applicability of the considered model and
highlight improvement opportunities to be implemented at the port of
Santos.
Abstract: Creating a database scheme is essentially a manual
process. From a requirement specification the information contained
within has to be analyzed and reduced into a set of tables, attributes
and relationships. This is a time consuming process that has to go
through several stages before an acceptable database schema is
achieved. The purpose of this paper is to implement a Natural
Language Processing (NLP) based tool to produce a relational
database from a requirement specification. The Stanford CoreNLP
version 3.3.1 and the Java programming were used to implement the
proposed model. The outcome of this study indicates that a first draft
of a relational database schema can be extracted from a requirement
specification by using NLP tools and techniques with minimum user
intervention. Therefore this method is a step forward in finding a
solution that requires little or no user intervention.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: The aim of this paper is to propose a novel technique
to guarantee Quality of Service (QoS) in a highly dynamic
environment. The MANET changes its topology dynamically as the
nodes are moved frequently. This will cause link failure between
mobile nodes. MANET cannot ensure reliability without delay. The
relay node is selected based on achieving QoS in previous
transmission. It considers one more factor Connection Existence
Period (CEP) to ensure reliability. CEP is to find out the period
during that connection exists between the nodes. The node with
highest CEP becomes a next relay node. The relay node is selected
dynamically to avoid frequent failure. The bandwidth of each link
changed dynamically based on service rate and request rate. This
paper proposes Active bandwidth setting up algorithm to guarantee
the QoS. The series of results obtained by using the Network
Simulator (NS-2) demonstrate the viability of our proposed
techniques.
Abstract: Opportunistic routing is used, where the network has
the features like dynamic topology changes and intermittent network
connectivity. In Delay tolerant network or Disruption tolerant
network opportunistic forwarding technique is widely used. The key
idea of opportunistic routing is selecting forwarding nodes to forward
data packets and coordination among these nodes to avoid duplicate
transmissions. This paper gives the analysis of pros and cons of
various opportunistic routing techniques used in MANET.
Abstract: This paper aims at finding a suitable neural network
for monitoring congestion level in electrical power systems. In this
paper, the input data has been framed properly to meet the target
objective through supervised learning mechanism by defining normal
and abnormal operating conditions for the system under study. The
congestion level, expressed as line congestion index (LCI), is
evaluated for each operating condition and is presented to the NN
along with the bus voltages to represent the input and target data.
Once, the training goes successful, the NN learns how to deal with a
set of newly presented data through validation and testing
mechanism. The crux of the results presented in this paper rests on
performance comparison of a multi-layered feed forward neural
network with eleven types of back propagation techniques so as to
evolve the best training criteria. The proposed methodology has been
tested on the standard IEEE-14 bus test system with the support of
MATLAB based NN toolbox. The results presented in this paper
signify that the Levenberg-Marquardt backpropagation algorithm
gives best training performance of all the eleven cases considered in
this paper, thus validating the proposed methodology.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: The construction of a new airport or the extension of
an existing one requires massive investments and many times public
private partnerships were considered in order to make feasible such
projects. One characteristic of these projects is uncertainty with
respect to financial and environmental impacts on the medium to long
term. Another one is the multistage nature of these types of projects.
While many airport development projects have been a success, some
others have turned into a nightmare for their promoters.
This communication puts forward a new approach for airport
investment risk assessment. The approach takes explicitly into
account the degree of uncertainty in activity levels prediction and
proposes milestones for the different stages of the project for
minimizing risk. Uncertainty is represented through fuzzy dual theory
and risk management is performed using dynamic programming. An
illustration of the proposed approach is provided.
Abstract: We used high-precision Global Positioning System
(GPS) to geodetically constrain the motion of stations in the
Darjiling-Sikkim Himalayan (DSH) wedge and examine the
deformation at the Indian-Tibetan plate boundary using IGS
(International GPS Service) fiducial stations. High-precision GPS
based displacement and velocity field was measured in the DSH
between 1997 and 2009. To obtain additional insight north of the
Indo-Tibetan border and in the Darjiling-Sikkim-Tibet (DaSiT)
wedge, published velocities from four stations J037, XIGA, J029 and
YADO were also included in the analysis. India-fixed velocities or
the back-slip was computed relative to the pole of rotation of the
Indian Plate (Latitude 52.97 ± 0.22º, Longitude - 0.30 ± 3.76º, and
Angular Velocity 0.500 ± 0.008º/ Myr) in the DaSiT wedge.
Dislocation modelling was carried out with the back-slip to model the
best possible solution of a finite rectangular dislocation or the
causative fault based on dislocation theory that produced the
observed back-slip using a forward modelling approach. To find the
best possible solution, three different models were attempted. First,
slip along a single thrust fault, then two thrust faults and in finally,
three thrust faults were modelled to simulate the back-slip in the
DaSiT wedge. The three-fault case bests the measured displacements
and is taken as the best possible solution.
Abstract: Control of a semi-batch polymerization reactor using
an adaptive radial basis function (RBF) neural network method is
investigated in this paper. A neural network inverse model is used to
estimate the valve position of the reactor; this method can identify the
controlled system with the RBF neural network identifier. The
weights of the adaptive PID controller are timely adjusted based on
the identification of the plant and self-learning capability of RBFNN.
A PID controller is used in the feedback control to regulate the actual
temperature by compensating the neural network inverse model
output. Simulation results show that the proposed control has strong
adaptability, robustness and satisfactory control performance and the
nonlinear system is achieved.
Abstract: The study investigated the implementation of the
Neural Network (NN) techniques for prediction of the loading of Cu
ions onto clinoptilolite. The experimental design using analysis of
variance (ANOVA) was chosen for testing the adequacy of the
Neural Network and for optimizing of the effective input parameters
(pH, temperature and initial concentration). Feed forward, multi-layer
perceptron (MLP) NN successfully tracked the non-linear behavior of
the adsorption process versus the input parameters with mean squared
error (MSE), correlation coefficient (R) and minimum squared error
(MSRE) of 0.102, 0.998 and 0.004 respectively. The results showed
that NN modeling techniques could effectively predict and simulate
the highly complex system and non-linear process such as ionexchange.
Abstract: Sustainability, being the urgent issue of our time, is
closely related with the innovations in technology. Nanotechnology
(NT), although not a new science, can be regarded relatively a new
science for buildings with brand new materials and applications. This
paper tends to give a research review of current and near future
applications of nanotechnology (NT) for achieving high-performance
and healthy buildings for a sustainable future. In the introduction, the
driving forces for the sustainability of construction industry are
explained. Then, the term NT is defined, and significance of
innovations in NT for a sustainable construction industry is revealed.
After presenting the application areas of NT and nanomaterials for
buildings with a number of cases, challenges in the adoption of this
technology are put forward, and finally the impacts of nanoparticles
and nanomaterials on human health and environment are discussed.