Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of spherical cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
spherical cross section by taking into account of the porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter,
porosity parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: Vegetation affects the mean and turbulent flow
structure. It may increase flood risks and sediment transport.
Therefore, it is important to develop analytical approaches for the bed
shear stress on vegetated bed, to predict resistance caused by
vegetation. In the recent years, experimental and numerical models
have both been developed to model the effects of submerged
vegetation on open-channel flow. In this paper, different analytic
models are compared and tested using the criteria of deviation, to
explore their capacity for predicting the mean velocity and select the
suitable one that will be applied in real case of rivers. The
comparison between the measured data in vegetated flume and
simulated mean velocities indicated, a good performance, in the case
of rigid vegetation, whereas, Huthoff model shows the best
agreement with a high coefficient of determination (R2=80%) and the
smallest error in the prediction of the average velocities.
Abstract: In this paper, a new trend for improvement in semianalytical
method based on scale boundaries in order to solve the 2D
elastodynamic problems is provided. In this regard, only the
boundaries of the problem domain discretization are by specific subparametric
elements. Mapping functions are uses as a class of higherorder
Lagrange polynomials, special shape functions, Gauss-Lobatto-
Legendre numerical integration, and the integral form of the weighted
residual method, the matrix is diagonal coefficients in the equations
of elastodynamic issues. Differences between study conducted and
prior research in this paper is in geometry production procedure of
the interpolation function and integration of the different is selected.
Validity and accuracy of the present method are fully demonstrated
through two benchmark problems which are successfully modeled
using a few numbers of DOFs. The numerical results agree very well
with the analytical solutions and the results from other numerical
methods.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: Recent research in neural networks science and
neuroscience for modeling complex time series data and statistical
learning has focused mostly on learning from high input space and
signals. Local linear models are a strong choice for modeling local
nonlinearity in data series. Locally weighted projection regression is
a flexible and powerful algorithm for nonlinear approximation in
high dimensional signal spaces. In this paper, different learning
scenario of one and two dimensional data series with different
distributions are investigated for simulation and further noise is
inputted to data distribution for making different disordered
distribution in time series data and for evaluation of algorithm in
locality prediction of nonlinearity. Then, the performance of this
algorithm is simulated and also when the distribution of data is high
or when the number of data is less the sensitivity of this approach to
data distribution and influence of important parameter of local
validity in this algorithm with different data distribution is explained.
Abstract: Parameters of flow are calculated in vaneless diffusers
with relative width 0,014–0,10. Inlet angles of flow and similarity
criteria were varied. There is information on flow separation,
boundary layer development, configuration of streamlines.
Polytrophic efficiency, loss coefficient and recovery coefficient are
used to compare effectiveness of diffusers. The sample of
optimization of narrow diffuser with conical walls is presented. Three
wide diffusers with narrowing walls are compared. The work is made
in the R&D laboratory “Gas dynamics of turbo machines” of the TU
SPb.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: Fracture in hot precision forging of engine valves was
investigated in this paper. The entire valve forging procedure was
described and the possible cause of the fracture was proposed. Finite
Element simulation was conducted for the forging process, with
commercial Finite Element code DEFORMTM. The effects of
material properties, the effect of strain rate and temperature were
considered in the FE simulation. Two fracture criteria were discussed
and compared, based on the accuracy and reliability of the FE
simulation results. The selected criterion predicted the fracture
location and shows the trend of damage increasing with good
accuracy, which matches the experimental observation. Additional
modification of the punch shapes was proposed to further reduce the
tendency of fracture in forging. Finite Element comparison shows a
great potential of such application in the mass production.
Abstract: The absorption power generation cycle based on the
ammonia-water mixture has attracted much attention for efficient
recovery of low-grade energy sources. In this paper a thermodynamic
performance analysis is carried out for a Kalina cycle using
ammonia-water mixture as a working fluid for efficient conversion of
low-temperature heat source in the form of sensible energy. The
effects of the source temperature on the system performance are
extensively investigated by using the thermodynamic models. The
results show that the source temperature as well as the ammonia mass
fraction affects greatly on the thermodynamic performance of the
cycle.
Abstract: A new method for determining the distribution of
birefringence and linear dichroism in optical polymer materials is
presented. The method is based on the use of polarizationholographic
diffraction grating that forms an orthogonal circular basis
in the process of diffraction of probing laser beam on the grating. The
intensities ratio of the orders of diffraction on this grating enables the
value of birefringence and linear dichroism in the sample to be
determined. The distribution of birefringence in the sample is
determined by scanning with a circularly polarized beam with a
wavelength far from the absorption band of the material. If the
scanning is carried out by probing beam with the wavelength near to
a maximum of the absorption band of the chromophore then the
distribution of linear dichroism can be determined. An appropriate
theoretical model of this method is presented. A laboratory setup was
created for the proposed method. An optical scheme of the laboratory
setup is presented. The results of measurement in polymer films with
two-dimensional gradient distribution of birefringence and linear
dichroism are discussed.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: A model reference adaptive control and a fixed gain
LQR control were implemented in the height controller of a quadrotor
that has parametric uncertainties due to the act of picking up an
object of unknown dimension and mass. It is shown that an adaptive
controller, unlike the fixed gain controller, is capable of ensuring a
stable tracking performance under such condition, although adaptive
control suffers from several limitations. The combination of both
adaptive and fixed gain control in the controller architecture can
result in an enhanced tracking performance in the presence parametric
uncertainties.