Abstract: The existing image coding standards generally degrades at low bit-rates because of the underlying block based Discrete Cosine Transform scheme. Over the past decade, the success of wavelets in solving many different problems has contributed to its unprecedented popularity. Due to implementation constraints scalar wavelets do not posses all the properties such as orthogonality, short support, linear phase symmetry, and a high order of approximation through vanishing moments simultaneously, which are very much essential for signal processing. New class of wavelets called 'Multiwavelets' which posses more than one scaling function overcomes this problem. This paper presents a new image coding scheme based on non linear approximation of multiwavelet coefficients along with multistage vector quantization. The performance of the proposed scheme is compared with the results obtained from scalar wavelets.
Abstract: Reliable secure multicast communication in mobile
adhoc networks is challenging due to its inherent characteristics of
infrastructure-less architecture with lack of central authority, high
packet loss rates and limited resources such as bandwidth, time and
power. Many emerging commercial and military applications require
secure multicast communication in adhoc environments. Hence key
management is the fundamental challenge in achieving reliable
secure communication using multicast key distribution for mobile
adhoc networks. Thus in designing a reliable multicast key
distribution scheme, reliability and congestion control over
throughput are essential components. This paper proposes and
evaluates the performance of an enhanced optimized multicast cluster
tree algorithm with destination sequenced distance vector routing
protocol to provide reliable multicast key distribution. Simulation
results in NS2 accurately predict the performance of proposed
scheme in terms of key delivery ratio and packet loss rate under
varying network conditions. This proposed scheme achieves
reliability, while exhibiting low packet loss rate with high key
delivery ratio compared with the existing scheme.
Abstract: The increasing demand for higher data rates in wireless communication systems has led to the more effective and efficient use of all allocated frequency bands. In order to use the whole bandwidth at maximum efficiency, one needs to have RF power amplifiers with a higher linear level and memory-less performance. This is considered to be a major challenge to circuit designers. In this thesis the linearity and memory are studied and examined via the behavior of the intermodulation distortion (IMD). A major source of the in-band distortion can be shown to be influenced by the out-of-band impedances presented at either the input or the output of the device, especially those impedances terminated the low frequency (IF) components. Thus, in order to regulate the in-band distortion, the out of-band distortion must be controllable. These investigations are performed on a 12W LDMOS device characterised at 2.1 GHz within a purpose built, high-power measurement system.
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: In this paper, we propose the low-MAC FEC controller for practical implementation of JPEG2000 image transmission using IEEE 802.15.4. The proposed low-MAC FEC controller has very small HW size and spends little computation to estimate channel state. Because of this advantage, it is acceptable to apply IEEE 802.15.4 which has to operate more than 1 year with battery. For the image transmission, we integrate the low-MAC FEC controller and RCPC coder in sensor node of LR-WPAN. The modified sensor node has increase of 3% hardware size than conventional zigbee sensor node.
Abstract: Variable channel conditions in underwater networks,
and variable distances between sensors due to water current, leads to
variable bit error rate (BER). This variability in BER has great
effects on energy efficiency of error correction techniques used. In
this paper an efficient energy adaptive hybrid error correction
technique (AHECT) is proposed. AHECT adaptively changes error
technique from pure retransmission (ARQ) in a low BER case to a
hybrid technique with variable encoding rates (ARQ & FEC) in a
high BER cases. An adaptation algorithm depends on a precalculated
packet acceptance rate (PAR) look-up table, current BER,
packet size and error correction technique used is proposed. Based
on this adaptation algorithm a periodically 3-bit feedback is added to
the acknowledgment packet to state which error correction technique
is suitable for the current channel conditions and distance.
Comparative studies were done between this technique and other
techniques, and the results show that AHECT is more energy
efficient and has high probability of success than all those
techniques.
Abstract: Full search block matching algorithm is widely used for hardware implementation of motion estimators in video compression algorithms. In this paper we are proposing a new architecture, which consists of a 2D parallel processing unit and a 1D unit both working in parallel. The proposed architecture reduces both data access power and computational power which are the main causes of power consumption in integer motion estimation. It also completes the operations with nearly the same number of clock cycles as compared to a 2D systolic array architecture. In this work sum of absolute difference (SAD)-the most repeated operation in block matching, is calculated in two steps. The first step is to calculate the SAD for alternate rows by a 2D parallel unit. If the SAD calculated by the parallel unit is less than the stored minimum SAD, the SAD of the remaining rows is calculated by the 1D unit. Early termination, which stops avoidable computations has been achieved with the help of alternate rows method proposed in this paper and by finding a low initial SAD value based on motion vector prediction. Data reuse has been applied to the reference blocks in the same search area which significantly reduced the memory access.
Abstract: in this work, we present a new strategy of direct adaptive control denoted: Extended minimal controller synthesis (EMCS). This algorithm is designed for an induction motor, which includes both electrical and mechanical dynamics under the assumptions of linear magnetic circuits. The main motivation of the EMCS control is to enhance the robustness of the MRAC algorithms, i.e. the rejection of bounded effects of rapidly varying external disturbances.
Abstract: In this paper, a planar antenna for UWB applications
has been proposed. The antenna consists of a square patch, a partial
ground plane and a slot on the ground plane. The proposed antenna is
easy to be integrated with microwave circuitry for low manufacturing
cost. The flat type antenna has a compact structure and the total size
is 14.5×14.5mm2. The result shows that the impedance bandwidth
(VSWR≤ 2) of the proposed antenna is 12.49 GHz (2.95 to 15.44
GHz), which is equivalent to 135.8%. Details of the proposed
compact planar UWB antenna design is presented and discussed.
Abstract: This paper introduces two decoders for binary linear
codes based on Metaheuristics. The first one uses a genetic algorithm
and the second is based on a combination genetic algorithm with
a feed forward neural network. The decoder based on the genetic
algorithms (DAG) applied to BCH and convolutional codes give good
performances compared to Chase-2 and Viterbi algorithm respectively
and reach the performances of the OSD-3 for some Residue
Quadratic (RQ) codes. This algorithm is less complex for linear
block codes of large block length; furthermore their performances
can be improved by tuning the decoder-s parameters, in particular the
number of individuals by population and the number of generations.
In the second algorithm, the search space, in contrast to DAG which
was limited to the code word space, now covers the whole binary
vector space. It tries to elude a great number of coding operations
by using a neural network. This reduces greatly the complexity of
the decoder while maintaining comparable performances.
Abstract: management of medical devices in hospitals includes
the planning of medical equipment acquisition and maintenance. The
presence of critical and non-critical areas together with technological
proliferation render the management of medical devices very
complex. This study creates an easy and objective methodology for
the analysis of medical equipment maintenance, that makes the
management of medical devices more feasible. The study has been
carried out at Florence Hospital Careggi and it aims to help the
clinical engineering department to manage medical equipment by
clarifying the hospital situation through a characterization of the
different areas, technologies and fault typologies.
Abstract: The gases generated in oil filled transformers can be
used for qualitative determination of incipient faults. The Dissolved
Gas Analysis has been widely used by utilities throughout the world
as the primarily diagnostic tool for transformer maintenance. In this
paper, various Artificial Intelligence Techniques that have been used
by the researchers in the past have been reviewed, some conclusions
have been drawn and a sequential hybrid system has been proposed.
The synergy of ANN and FIS can be a good solution for reliable
results for predicting faults because one should not rely on a single
technology when dealing with real–life applications.
Abstract: This paper deals with condition monitoring of electric switch machine for railway points. Point machine, as a complex electro-mechanical device, switch the track between two alternative routes. There has been an increasing interest in railway safety and the optimal management of railway equipments maintenance, e.g. point machine, in order to enhance railway service quality and reduce system failure. This paper explores the development of Kolmogorov- Smirnov (K-S) test to detect some point failures (external to the machine, slide chairs, fixing, stretchers, etc), while the point machine (inside the machine) is in its proper condition. Time-domain stator Current signatures of normal (healthy) and faulty points are taken by 3 Hall Effect sensors and are analyzed by K-S test. The test is simulated by creating three types of such failures, namely putting a hard stone and a soft stone between stock rail and switch blades as obstacles and also slide chairs- friction. The test has been applied for those three faults which the results show that K-S test can effectively be developed for the aim of other point failures detection, which their current signatures deviate parametrically from the healthy current signature. K-S test as an analysis technique, assuming that any defect has a specific probability distribution. Empirical cumulative distribution functions (ECDF) are used to differentiate these probability distributions. This test works based on the null hypothesis that ECDF of target distribution is statistically similar to ECDF of reference distribution. Therefore by comparing a given current signature (as target signal) from unknown switch state to a number of template signatures (as reference signal) from known switch states, it is possible to identify which is the most likely state of the point machine under analysis.
Abstract: Wireless sensor networks are consisted of hundreds or
thousands of small sensors that have limited resources.
Energy-efficient techniques are the main issue of wireless sensor
networks. This paper proposes an energy efficient agent-based
framework in wireless sensor networks. We adopt biologically
inspired approaches for wireless sensor networks. Agent operates
automatically with their behavior policies as a gene. Agent aggregates
other agents to reduce communication and gives high priority to nodes
that have enough energy to communicate. Agent behavior policies are
optimized by genetic operation at the base station. Simulation results
show that our proposed framework increases the lifetime of each node.
Each agent selects a next-hop node with neighbor information and
behavior policies. Our proposed framework provides self-healing,
self-configuration, self-optimization properties to sensor nodes.
Abstract: Wireless sensor networks have been used in wide
areas of application and become an attractive area for researchers in
recent years. Because of the limited energy storage capability of
sensor nodes, Energy consumption is one of the most challenging
aspects of these networks and different strategies and protocols deals
with this area. This paper presents general methods for designing low
power wireless sensor network. Different sources of energy
consumptions in these networks are discussed here and techniques for
alleviating the consumption of energy are presented.
Abstract: In the age of global communications, heterogeneous
networks are seen to be the best choice of strategy to ensure continuous and uninterruptible services. This will allow mobile
terminal to stay in connection even they are migrating into different segment coverage through the handoff process. With the increase of
teletraffic demands in mobile cellular system, hierarchical cellular systems have been adopted extensively for more efficient channel
utilization and better QoS (Quality of Service). This paper presents a
bidirectional call overflow scheme between two layers of microcells and macrocells, where handoffs are decided by the velocity of mobile
making the call. To ensure that handoff calls are given higher priorities, it is assumed that guard channels are assigned in both
macrocells and microcells. A hysteresis value introduced in mobile velocity is used to allow mobile roam in the same cell if its velocity
changes back within the set threshold values. By doing this the number of handoffs is reduced thereby reducing the processing overhead and enhancing the quality of service to the end user.
Abstract: Currently, there are many local area industrial networks
that can give guaranteed bandwidth to synchronous traffic, particularly
providing CBR channels (Constant Bit Rate), which allow
improved bandwidth management. Some of such networks operate
over Ethernet, delivering channels with enough capacity, specially
with compressors, to integrate multimedia traffic in industrial monitoring
and image processing applications with many sources. In
these industrial environments where a low latency is an essential
requirement, JPEG is an adequate compressing technique but it
generates VBR traffic (Variable Bit Rate). Transmitting VBR traffic
in CBR channels is inefficient and current solutions to this problem
significantly increase the latency or further degrade the quality. In
this paper an R(q) model is used which allows on-line calculation of
the JPEG quantification factor. We obtained increased quality, a lower
requirement for the CBR channel with reduced number of discarded
frames along with better use of the channel bandwidth.
Abstract: We introduce, a new interactive 3D simulation system of ocular motion and expressions suitable for: (1) character animation applications to game design, film production, HCI (Human Computer Interface), conversational animated agents, and virtual reality; (2) medical applications (ophthalmic neurological and muscular pathologies: research and education); and (3) real time simulation of unconscious cognitive and emotional responses (for use, e.g., in psychological research). The system is comprised of: (1) a physiologically accurate parameterized 3D model of the eyes, eyelids, and eyebrow regions; and (2) a prototype device for realtime control of eye motions and expressions, including unconsciously produced expressions, for application as in (1), (2), and (3) above. The 3D eye simulation system, created using state-of-the-art computer animation technology and 'optimized' for use with an interactive and web deliverable platform, is, to our knowledge, the most advanced/realistic available so far for applications to character animation and medical pedagogy.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: Wavelength multiplexing (WDM) technology along
with optical amplifiers is used for optical communication systems in
S-band, C-band and L-band. To improve the overall system
performance Hybrid amplifiers consisting of cascaded TDFA and
EDFA with different gain bandwidths are preferred for long haul
wavelength multiplexed optical communication systems. This paper
deals with statistical analysis of different configuration of hybrid
amplifier i.e. analysis of TDFA-EDFA configuration and EDFA –
TDFA configuration. In this paper One-Way ANOVA method is used
for statistical analysis.