Abstract: For higher order multiplications, a huge number of
adders or compressors are to be used to perform the partial product
addition. We have reduced the number of adders by introducing
special kind of adders that are capable to add five/six/seven bits per
decade. These adders are called compressors. Binary counter
property has been merged with the compressor property to develop
high order compressors. Uses of these compressors permit the
reduction of the vertical critical paths. A 16×16 bit multiplier has
been developed using these compressors. These compressors make
the multipliers faster as compared to the conventional design that
have been used 4-2 compressors and 3-2 compressors.
Abstract: Smoothing or filtering of data is first preprocessing step
for noise suppression in many applications involving data analysis.
Moving average is the most popular method of smoothing the data,
generalization of this led to the development of Savitzky-Golay filter.
Many window smoothing methods were developed by convolving
the data with different window functions for different applications;
most widely used window functions are Gaussian or Kaiser. Function
approximation of the data by polynomial regression or Fourier
expansion or wavelet expansion also gives a smoothed data. Wavelets
also smooth the data to great extent by thresholding the wavelet
coefficients. Almost all smoothing methods destroys the peaks and
flatten them when the support of the window is increased. In certain
applications it is desirable to retain peaks while smoothing the data
as much as possible. In this paper we present a methodology called
as peak-wise smoothing that will smooth the data to any desired level
without losing the major peak features.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: In 3D-wavelet video coding framework temporal
filtering is done along the trajectory of motion using Motion
Compensated Temporal Filtering (MCTF). Hence computationally
efficient motion estimation technique is the need of MCTF. In this
paper a predictive technique is proposed in order to reduce the
computational complexity of the MCTF framework, by exploiting
the high correlation among the frames in a Group Of Picture (GOP).
The proposed technique applies coarse and fine searches of any fast
block based motion estimation, only to the first pair of frames in a
GOP. The generated motion vectors are supplied to the next
consecutive frames, even to subsequent temporal levels and only fine
search is carried out around those predicted motion vectors. Hence
coarse search is skipped for all the motion estimation in a GOP
except for the first pair of frames. The technique has been tested for
different fast block based motion estimation algorithms over different
standard test sequences using MC-EZBC, a state-of-the-art scalable
video coder. The simulation result reveals substantial reduction (i.e.
20.75% to 38.24%) in the number of search points during motion
estimation, without compromising the quality of the reconstructed
video compared to non-predictive techniques. Since the motion
vectors of all the pair of frames in a GOP except the first pair will
have value ±1 around the motion vectors of the previous pair of
frames, the number of bits required for motion vectors is also
reduced by 50%.
Abstract: A generalized method for small-signal simulation of
avalanche noise in Mixed Tunneling Avalanche Transit Time
(MITATT) device is presented in this paper where the effect of series
resistance is taken into account. The method is applied to a
millimeter-wave Double Drift Region (DDR) MITATT device based
on Silicon to obtain noise spectral density and noise measure as a
function of frequency for different values of series resistance. It is
found that noise measure of the device at the operating frequency
(122 GHz) with input power density of 1010 Watt/m2 is about 35 dB
for hypothetical parasitic series resistance of zero ohm (estimated
junction temperature = 500 K). Results show that the noise measure
increases as the value of parasitic resistance increases.
Abstract: Cosmic showers, during the transit through space, produce
sub - products as a result of interactions with the intergalactic
or interstellar medium which after entering earth generate secondary
particles called Extensive Air Shower (EAS). Detection and analysis
of High Energy Particle Showers involve a plethora of theoretical and
experimental works with a host of constraints resulting in inaccuracies
in measurements. Therefore, there exist a necessity to develop a
readily available system based on soft-computational approaches
which can be used for EAS analysis. This is due to the fact that soft
computational tools such as Artificial Neural Network (ANN)s can be
trained as classifiers to adapt and learn the surrounding variations. But
single classifiers fail to reach optimality of decision making in many
situations for which Multiple Classifier System (MCS) are preferred
to enhance the ability of the system to make decisions adjusting
to finer variations. This work describes the formation of an MCS
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN) with data inputs
from correlation mapping Self Organizing Map (SOM) blocks and
the output optimized by another SOM. The results show that the setup
can be adopted for real time practical applications for prediction
of primary energy and location of EAS from density values captured
using detectors in a circular grid.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: In this paper we present an approach for 3D face
recognition based on extracting principal components of range
images by utilizing modified PCA methods namely 2DPCA and
bidirectional 2DPCA also known as (2D) 2 PCA.A preprocessing
stage was implemented on the images to smooth them using median
and Gaussian filtering. In the normalization stage we locate the nose
tip to lay it at the center of images then crop each image to a standard
size of 100*100. In the face recognition stage we extract the principal
component of each image using both 2DPCA and (2D) 2 PCA.
Finally, we use Euclidean distance to measure the minimum distance
between a given test image to the training images in the database. We
also compare the result of using both methods. The best result
achieved by experiments on a public face database shows that 83.3
percent is the rate of face recognition for a random facial expression.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: This paper investigates the issue of building decision
trees from data with imprecise class values where imprecision is
encoded in the form of possibility distributions. The Information
Affinity similarity measure is introduced into the well-known gain
ratio criterion in order to assess the homogeneity of a set of
possibility distributions representing instances-s classes belonging to
a given training partition. For the experimental study, we proposed an
information affinity based performance criterion which we have used
in order to show the performance of the approach on well-known
benchmarks.
Abstract: High speed networks provide realtime variable bit rate
service with diversified traffic flow characteristics and quality
requirements. The variable bit rate traffic has stringent delay and
packet loss requirements. The burstiness of the correlated traffic
makes dynamic buffer management highly desirable to satisfy the
Quality of Service (QoS) requirements. This paper presents an
algorithm for optimization of adaptive buffer allocation scheme for
traffic based on loss of consecutive packets in data-stream and buffer
occupancy level. Buffer is designed to allow the input traffic to be
partitioned into different priority classes and based on the input
traffic behavior it controls the threshold dynamically. This algorithm
allows input packets to enter into buffer if its occupancy level is less
than the threshold value for priority of that packet. The threshold is
dynamically varied in runtime based on packet loss behavior. The
simulation is run for two priority classes of the input traffic –
realtime and non-realtime classes. The simulation results show that
Adaptive Partial Buffer Sharing (ADPBS) has better performance
than Static Partial Buffer Sharing (SPBS) and First In First Out
(FIFO) queue under the same traffic conditions.
Abstract: Individually Network reconfiguration or Capacitor control
perform well in minimizing power loss and improving voltage
profile of the distribution system. But for heavy reactive power loads
network reconfiguration and for heavy active power loads capacitor
placement can not effectively reduce power loss and enhance
voltage profiles in the system. In this paper, an hybrid approach
that combine network reconfiguration and capacitor placement using
Harmony Search Algorithm (HSA) is proposed to minimize power
loss reduction and improve voltage profile. The proposed approach
is tested on standard IEEE 33 and 16 bus systems. Computational
results show that the proposed hybrid approach can minimize losses
more efficiently than Network reconfiguration or Capacitor control.
The results of proposed method are also compared with results
obtained by Simulated Annealing (SA). The proposed method has
outperformed in terms of the quality of solution compared to SA.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: Optimal reactive power flow is an optimization problem
with one or more objective of minimizing the active power losses for
fixed generation schedule. The control variables are generator bus
voltages, transformer tap settings and reactive power output of the
compensating devices placed on different bus bars. Biogeography-
Based Optimization (BBO) technique has been applied to solve
different kinds of optimal reactive power flow problems subject
to operational constraints like power balance constraint, line flow
and bus voltages limits etc. BBO searches for the global optimum
mainly through two steps: Migration and Mutation. In the present
work, BBO has been applied to solve the optimal reactive power
flow problems on IEEE 30-bus and standard IEEE 57-bus power
systems for minimization of active power loss. The superiority of the
proposed method has been demonstrated. Considering the quality of
the solution obtained, the proposed method seems to be a promising
one for solving these problems.
Abstract: This paper presents a methodology for operational and
economic characteristics based evaluation and selection of a power
plant using Graph theoretic approach. A universal evaluation index
on the basis of Operational and economics characteristics of a plant is
proposed which evaluates and ranks the various types of power plants.
The index thus obtained from the pool of operational characteristics
of the power plant attributes Digraph. The Digraph is developed
considering Operational and economics attributes of the power plants
and their relative importance for their smooth operation, installation
and commissioning and prioritizing their selection. The sensitivity
analysis of the attributes towards the objective has also been carried
out in order to study the impact of attributes over the desired outcome
i.e. the universal operational-economics index of the power plant.
Abstract: This paper presents the applications of computational intelligence techniques to economic load dispatch problems. The fuel cost equation of a thermal plant is generally expressed as continuous quadratic equation. In real situations the fuel cost equations can be discontinuous. In view of the above, both continuous and discontinuous fuel cost equations are considered in the present paper. First, genetic algorithm optimization technique is applied to a 6- generator 26-bus test system having continuous fuel cost equations. Results are compared to conventional quadratic programming method to show the superiority of the proposed computational intelligence technique. Further, a 10-generator system each with three fuel options distributed in three areas is considered and particle swarm optimization algorithm is employed to minimize the cost of generation. To show the superiority of the proposed approach, the results are compared with other published methods.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.
Abstract: This paper solves the environmental/ economic dispatch
power system problem using the Non-dominated Sorting Genetic
Algorithm-II (NSGA-II) and its hybrid with a Convergence Accelerator
Operator (CAO), called the NSGA-II/CAO. These multiobjective
evolutionary algorithms were applied to the standard IEEE 30-bus
six-generator test system. Several optimization runs were carried out
on different cases of problem complexity. Different quality measure
which compare the performance of the two solution techniques were
considered. The results demonstrated that the inclusion of the CAO
in the original NSGA-II improves its convergence while preserving
the diversity properties of the solution set.
Abstract: One major source of performance decline in speaker
recognition system is channel mismatch between training and testing.
This paper focuses on improving channel robustness of speaker
recognition system in two aspects of channel compensation technique
and channel robust features. The system is text-independent speaker
identification system based on two-stage recognition. In the aspect of
channel compensation technique, this paper applies MAP (Maximum
A Posterior Probability) channel compensation technique, which was
used in speech recognition, to speaker recognition system. In the
aspect of channel robust features, this paper introduces
pitch-dependent features and pitch-dependent speaker model for the
second stage recognition. Based on the first stage recognition to
testing speech using GMM (Gaussian Mixture Model), the system
uses GMM scores to decide if it needs to be recognized again. If it
needs to, the system selects a few speakers from all of the speakers
who participate in the first stage recognition for the second stage
recognition. For each selected speaker, the system obtains 3
pitch-dependent results from his pitch-dependent speaker model, and
then uses ANN (Artificial Neural Network) to unite the 3
pitch-dependent results and 1 GMM score for getting a fused result.
The system makes the second stage recognition based on these fused
results. The experiments show that the correct rate of two-stage
recognition system based on MAP channel compensation technique
and pitch-dependent features is 41.7% better than the baseline system
for closed-set test.
Abstract: Recent research result has shown that two multidelay
feedback systems can synchronize each other under different
schemes, i.e. lag, projective-lag, anticipating, or projectiveanticipating
synchronization. There, the driving signal is significantly
complex due that it is constituted by multiple nonlinear transformations
of delayed state variable. In this paper, a secure communication
model is proposed based on synchronization of coupled multidelay
feedback systems, in which the plain signal is mixed with a complex
signal at the transmitter side and it is precisely retrieved at the receiver
side. The effectiveness of the proposed model is demonstrated and
verified in the specific example, where the message signal is masked
directly by the complex signal and security is examined under the
breaking method of power spectrum analysis.