Abstract: It is quite essential to investigate the causes of
pavement deterioration in order to select the proper maintenance
technique. The objective of this study was to identify factors cause
deterioration of recently constructed roads in Khartoum state. A
comprehensive literature concerning the factors of road deterioration,
common road defects and their causes were reviewed. Three major
road projects with different deterioration reasons were selected for
this study. The investigation involved field survey and laboratory
testing on those projects to examine the existing pavement
conditions. The results revealed that the roads investigated
experienced severe failures in the forms of cracks, potholes, and
rutting in the wheel path. The causes of those failures were found
mainly linked to poor drainage, traffic overloading, expansive
subgrade soils, and the use of low quality materials in construction.
Based on the results, recommendations were provided to help
highway engineers in selecting the most effective repair techniques
for specific kinds of distresses.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: Green concrete are generally composed of recycling
materials as hundred or partial percent substitutes for aggregate,
cement, and admixture in concrete. To reduce greenhouse gas
emissions, efforts are needed to develop environmentally friendly
construction materials. Using of fly ash based geopolymer as an
alternative binder can help reduce CO2 emission of concrete. The
binder of geopolymer concrete is different from the ordinary Portland
cement concrete. Geopolymer Concrete specimens were prepared
with different concentration of NaOH solution M10, M14, and, M16
and cured at 60ºC in duration of 24 hours and 8 hours, in addition to
the curing in direct sunlight. Thus, it is necessary to study the effects
of the geopolymer binder on the behavior of concrete. Concrete is
made by using geopolymer technology is environmental friendly and
could be considered as part of the sustainable development. In this
study, the Local Alkaline Activator in Egypt and crashed stone as
coarse aggregate in fly ash based-geopolymer concrete was
investigated. This paper illustrates the development of mechanical
properties. Since the gained compressive strength for geopolymer
concrete at 28 days was in the range of 22.5MPa – 43.9MPa.
Abstract: Steel extended end plate bolted connections are
recommended to be widely utilized in special moment-resisting frame
subjected to monotonic loading. Improper design of steel beam to
column connection can lead to the collapse and fatality of structures.
Therefore comprehensive research studies of beam to column
connection design should be carried out. Also the performance and
effect of corrugated on the strength of beam column end plate
connection up to failure under monotonic loading in horizontal
direction is presented in this paper. The non-linear elastic–plastic
behavior has been considered through a finite element analysis using
the multi-purpose software package LUSAS. The effect of vertically
and horizontally types of corrugated web was also investigated.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: A number of studies have been conducted recently to
investigate the influence of randomly oriented fibers on some
engineering properties of cohesive and cohesionless soils. However,
few studies have been carried out on freezing-thawing behavior of
fine-grained soils modified with discrete fiber inclusions and additive
materials. This experimental study was performed to investigate the
effect of randomly distributed polypropylene fibers (PP) and some
additive materials [e.g.., borogypsum (BG), fly ash (FA) and cement
(C)] on freezing-thawing durability (mass losses) of a fine-grained
soil for 6, 12, and 18 cycles. The Taguchi method was applied to the
experiments and a standard L9 orthogonal array (OA) with four
factors and three levels were chosen. A series of freezing-thawing
tests were conducted on each specimen. 0-20% BG, 0-20% FA, 0-
0.25% PP and 0-3% of C by total dry weight of mixture were used in
the preparation of specimens. Experimental results showed that the
most effective materials for the freezing-thawing durability (mass
losses) of the samples were borogypsum and fly ash. The values of
mass losses for 6, 12 and 18 cycles in optimum conditions were
16.1%, 5.1% and 3.6%, respectively.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: Response Surface Methods (RSM) provide
statistically validated predictive models that can then be manipulated
for finding optimal process configurations. Variation transmitted to
responses from poorly controlled process factors can be accounted
for by the mathematical technique of propagation of error (POE),
which facilitates ‘finding the flats’ on the surfaces generated by
RSM. The dual response approach to RSM captures the standard
deviation of the output as well as the average. It accounts for
unknown sources of variation. Dual response plus propagation of
error (POE) provides a more useful model of overall response
variation. In our case, we implemented this technique in predicting
compressive strength of concrete of 28 days in age. Since 28 days is
quite time consuming, while it is important to ensure the quality
control process. This paper investigates the potential of using design
of experiments (DOE-RSM) to predict the compressive strength of
concrete at 28th day. Data used for this study was carried out from
experiment schemes at university of Benghazi, civil engineering
department. A total of 114 sets of data were implemented. ACI mix
design method was utilized for the mix design. No admixtures were
used, only the main concrete mix constituents such as cement, coarseaggregate,
fine aggregate and water were utilized in all mixes.
Different mix proportions of the ingredients and different water
cement ratio were used. The proposed mathematical models are
capable of predicting the required concrete compressive strength of
concrete from early ages.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: This paper aimed to introduce the solution of concrete
slump recovery using chemical admixture type-F (superplasticizer,
naphthalene base) to the practice in order to solve unusable concrete
problem due to concrete loss its slump, especially for those tropical
countries that have faster slump loss rate. In the other hand, randomly
adding superplasticizer into concrete can cause concrete to segregate.
Therefore, this paper also develops the estimation model used to
calculate amount of second dose of superplasticizer need for concrete
slump recovery. Fresh properties of ordinary Portland cement
concrete with volumetric ratio of paste to void between aggregate
(paste content) of 1.1-1.3 with water-cement ratio zone of 0.30 to
0.67 and initial superplasticizer (naphthalene base) of 0.25%-1.6%
were tested for initial slump and slump loss for every 30 minutes for
one and half hour by slump cone test. Those concretes with slump
loss range from 10% to 90% were re-dosed and successfully
recovered back to its initial slump. Slump after re-dosed was tested
by slump cone test. From the result, it has been concluded that, slump
loss was slower for those mix with high initial dose of
superplasticizer due to addition of superplasticizer will disturb
cement hydration. The required second dose of superplasticizer was
affected by two major parameters, which were water-cement ratio
and paste content, where lower water-cement ratio and paste content
cause an increase in require second dose of superplasticizer. The
amount of second dose of superplasticizer is higher as the solid
content within the system is increase, solid can be either from cement
particles or aggregate. The data was analyzed to form an equation use
to estimate the amount of second dosage requirement of
superplasticizer to recovery slump to its original.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: Average temperatures worldwide are expected to
continue to rise. At the same time, major cities in developing
countries are becoming increasingly populated and polluted.
Governments are tasked with the problem of overheating and air
quality in residential buildings. This paper presents the development
of a model, which is able to estimate the occupant exposure
to extreme temperatures and high air pollution within domestic
buildings. Building physics simulations were performed using the
EnergyPlus building physics software. An accurate metamodel is
then formed by randomly sampling building input parameters and
training on the outputs of EnergyPlus simulations. Metamodels are
used to vastly reduce the amount of computation time required when
performing optimisation and sensitivity analyses. Neural Networks
(NNs) have been compared to a Radial Basis Function (RBF)
algorithm when forming a metamodel. These techniques were
implemented using the PyBrain and scikit-learn python libraries,
respectively. NNs are shown to perform around 15% better than RBFs
when estimating overheating and air pollution metrics modelled by
EnergyPlus.
Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.
Abstract: Sewage sludge is a biomass resource that can create a
solid fuel and electricity. Utilizing sewage sludge as a renewable
energy can contribute to the reduction of greenhouse gases. In Japan,
the "National Plan for the Promotion of Biomass Utilization" and the
“Priority Plan for Social Infrastructure Development" were approved
at cabinet meetings in December 2010 and August 2012, respectively,
to promote the energy utilization of sewage sludge. This study
investigated costs and greenhouse gas emission in different sewage
sludge treatments with technologies for energy from sewage sludge.
Expenses were estimated based on capital costs and O&M costs
including energy consumption of solid fuel plants and biogas power
generation plants for sewage sludge. Results showed that the cost of
sludge digestion treatment with solid fuel technologies was 8% lower
than landfill disposal. The greenhouse gas emission of sludge
digestion treatment with solid fuel technologies was also 6,390t as
CO2 smaller than landfill disposal. Biogas power generation reduced
the electricity of a wastewater treatment plant by 30% and the cost by
5%.
Abstract: Over the last two decades, externally bonded fiber
reinforced polymer (FRP) composites bonded to concrete substrates
has become a popular method for strengthening reinforced concrete
(RC) highway and railway bridges. Such structures are exposed to
severe cyclic loading throughout their lifetime often resulting in
fatigue damage to structural components and a reduction in the
service life of the structure. Since experimental and numerical results
on the fatigue performance of FRP-to-concrete joints are still limited,
the current research focuses on assessing the fatigue performance of
externally bonded FRP-to-concrete joints using a direct shear test.
Some early results indicate that the stress ratio and the applied cyclic
stress level have a direct influence on the fatigue life of the externally
bonded FRP. In addition, a calibrated finite element model is
developed to provide further insight into the influence of certain
parameters such as: concrete strength, FRP thickness, number of
cycles, frequency, and stiffness on the fatigue life of the FRP-toconcrete
joints.