Abstract: SUVA (equivalent to UV254/DOC) value in raw water is a precursor for the formation of trihalomethane during chlorination at a water treatment plant. This study collected rapidly filtered water from an advanced water treatment plant for use in experiments on raw water. The removal rate of treating the trihalomethanes formation potential (THMFP) was conducted by using a biological activated carbon. The hydraulic retention time and SUVA loading were major factors in biological degradation tests. The results showed that biological powder-activated carbon (BPAC) lowered the average concentration of UV254 and value of SUVA in raw water. A removal efficiency of THMFP was present in the treatment of the three primary organic carbon items. These results highlighted the importance of the BPAC had an excellent treatment efficiency on THMFP.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: In this paper, we have proposed a novel FinFET with
extended body under the poly gate, which is called EB-FinFET, and
its characteristic is demonstrated by using three-dimensional (3-D)
numerical simulation. We have analyzed and compared it with
conventional FinFET. The extended body height dependence on the
drain induced barrier lowering (DIBL) and subthreshold swing (S.S)
have been also investigated. According to the 3-D numerical
simulation, the proposed structure has a firm structure, an acceptable
short channel effect (SCE), a reduced series resistance, an increased
on state drain current (I
on) and a large normalized I
DS. Furthermore,
the structure can also improve corner effect and reduce self-heating
effect due to the extended body. Our results show that the EBFinFET
is excellent for nanoscale device.
Abstract: The health record in the Electronic Health Record
(EHR) system is more sensitive than demographic. It raises the
important issue for the EHR requirement in privacy, security, audit
trail, patient access, and archiving and data retention. The studies
about the EHR system security are deficient. The aim of this study is to
build a security environment for the EHR system by Integrating the
Healthcare Enterprise (IHE) Audit Trail and Node Authentication
Security (ATNA) profile. The CDAs can be access in a secure EHR
environment.
Abstract: This study applied the Gaussian trajectory
transfer-coefficient model (GTx) to simulate the particulate matter
concentrations and the source apportionments at Nanzih Air Quality
Monitoring Station in southern Taiwan from November 2007 to
February 2008. The correlation coefficient between the observed and
the calculated daily PM10 concentrations is 0.5 and the absolute bias of
the PM10 concentrations is 24%. The simulated PM10 concentrations
matched well with the observed data. Although the emission rate of
PM10 was dominated by area sources (58%), the results of source
apportionments indicated that the primary sources for PM10 at Nanzih
Station were point sources (42%), area sources (20%) and then upwind
boundary concentration (14%). The obvious difference of PM10 source
apportionment between episode and non-episode days was upwind
boundary concentrations which contributed to 20% and 11% PM10
sources, respectively. The gas-particle conversion of secondary
aerosol and long range transport played crucial roles on the PM10
contribution to a receptor.
Abstract: A product development for green logistics model using
the fuzzy analytic network process method is presented for evaluating
the relationships among the product design, the manufacturing
activities, and the green supply chain. In the product development
stage, there can be alternative ways to design the detailed components
to satisfy the design concept and product requirement. In different
design alternative cases, the manufacturing activities can be different.
In addition, the manufacturing activities can affect the green supply
chain of the components and product. In this research, a fuzzy analytic
network process evaluation model is presented for evaluating the
criteria in product design, manufacturing activities, and green supply
chain. The comparison matrices for evaluating the criteria among the
three groups are established. The total relational values between the
three groups represent the relationships and effects. In application, the
total relational values can be used to evaluate the design alternative
cases for decision-making to select a suitable design case and the green
supply chain. In this presentation, an example product is illustrated. It
shows that the model is useful for integrated evaluation of design and
manufacturing and green supply chain for the purpose of product
development for green logistics.
Abstract: In this study, three strains of Vibrio parahaemolyticus
(690, BCRC 13023 and BCRC 13025) were subjected to acid
adaptation at pH 5.5 for 90 min. The survival of acid-adapted and
non-adapted V. parahaemolyticus strains under simulated gastric
condition and their protein expression profiles were investigated.
Results showed that acid adaptation increased the survival of the test
V. parahaemolyticus strains after exposure to simulated gastric juice
(pH 3). Additionally, acid adaptation also affected the protein
expression in these V. parahaemolyticus strains. Nine proteins,
identified as atpA, atpB, DnaK, GroEL, OmpU, enolase,
fructose-bisphosphate aldolase, phosphoglycerate kinase and
triosephosphate isomerase, were induced by acid adaptation in two or
three of the test strains. These acid-adaptive proteins may play
important regulatory roles in the acid tolerance response (ATR) of V.
parahaemolyticus.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: This study examined the effects of neuromuscular
training (NT) on limits of stability (LOS) in female individuals.
Twenty female basketball amateurs were assigned into NT
experimental group or control group by volunteer. All the players were
underwent regular basketball practice, 90 minutes, 3 times per week
for 6 weeks, but the NT experimental group underwent extra NT with
plyometric and core training, 50 minutes, 3 times per week for 6 weeks
during this period. Limits of stability (LOS) were evaluated by the
Biodex Balance System. One factor ANCOVA was used to examine
the differences between groups after training. The significant level for
statistic was set at p
Abstract: The objective of this research is to develop an advanced driver assistance system characterized with the functions of lane departure warning (LDW), forward collision warning (FCW) and adaptive front-lighting system (AFS). The system is mainly configured a CCD/CMOS camera to acquire the images of roadway ahead in association with the analysis made by an image-processing unit concerning the lane ahead and the preceding vehicles. The input image captured by a camera is used to recognize the lane and the preceding vehicle positions by image detection and DROI (Dynamic Range of Interesting) algorithms. Therefore, the system is able to issue real-time auditory and visual outputs of warning when a driver is departing the lane or driving too close to approach the preceding vehicle unwittingly so that the danger could be prevented from occurring. During the nighttime, in addition to the foregoing warning functions, the system is able to control the bending light of headlamp to provide an immediate light illumination when making a turn at a curved lane and adjust the level automatically to reduce the lighting interference against the oncoming vehicles driving in the opposite direction by the curvature of lane and the vanishing point estimations. The experimental results show that the integrated vehicle image system is robust to most environments such as the lane detection and preceding vehicle detection average accuracy performances are both above 90 %.
Abstract: In this paper, we propose a novel metal oxide
semiconductor field effect transistor with L-shaped channel structure
(LMOS), and several type of L-shaped structures are also designed,
studied and compared with the conventional MOSFET device for the
same average gate length (Lavg). The proposed device electrical
characteristics are analyzed and evaluated by three dimension (3-D)
ISE-TCAD simulator. It can be confirmed that the LMOS devices
have higher on-state drain current and both lower drain-induced
barrier lowering (DIBL) and subthreshold swing (S.S.) than its
conventional counterpart has. In addition, the transconductance and
voltage gain properties of the LMOS are also improved.
Abstract: A novel PDE solver using the multidimensional wave
digital filtering (MDWDF) technique to achieve the solution of a 2D
seismic wave system is presented. In essence, the continuous physical
system served by a linear Kirchhoff circuit is transformed to an
equivalent discrete dynamic system implemented by a MD wave
digital filtering (MDWDF) circuit. This amounts to numerically
approximating the differential equations used to describe elements of a
MD passive electronic circuit by a grid-based difference equations
implemented by the so-called state quantities within the passive
MDWDF circuit. So the digital model can track the wave field on a
dense 3D grid of points. Details about how to transform the continuous
system into a desired discrete passive system are addressed. In
addition, initial and boundary conditions are properly embedded into
the MDWDF circuit in terms of state quantities. Graphic results have
clearly demonstrated some physical effects of seismic wave (P-wave
and S–wave) propagation including radiation, reflection, and
refraction from and across the hard boundaries. Comparison between
the MDWDF technique and the finite difference time domain (FDTD)
approach is also made in terms of the computational efficiency.
Abstract: In the traditional concept of product life cycle management, the activities of design, manufacturing, and assembly are performed in a sequential way. The drawback is that the considerations in design may contradict the considerations in manufacturing and assembly. The different designs of components can lead to different assembly sequences. Therefore, in some cases, a good design may result in a high cost in the downstream assembly activities. In this research, an integrated design evaluation and assembly sequence planning model is presented. Given a product requirement, there may be several design alternative cases to design the components for the same product. If a different design case is selected, the assembly sequence for constructing the product can be different. In this paper, first, the designed components are represented by using graph based models. The graph based models are transformed to assembly precedence constraints and assembly costs. A particle swarm optimization (PSO) approach is presented by encoding a particle using a position matrix defined by the design cases and the assembly sequences. The PSO algorithm simultaneously performs design evaluation and assembly sequence planning with an objective of minimizing the total assembly costs. As a result, the design cases and the assembly sequences can both be optimized. The main contribution lies in the new concept of integrated design evaluation and assembly sequence planning model and the new PSO solution method. The test results show that the presented method is feasible and efficient for solving the integrated design evaluation and assembly planning problem. In this paper, an example product is tested and illustrated.
Abstract: This paper presents a novel sinusoidal modulation
scheme that features least correlated noise and high linearity. The
modulation circuit, which is composed of a quantizer, a resonator, and
a comparator, is capable of eliminating correlated modulation noise
while doing modulation. The proposed modulation scheme combined
with the linear quadratic optimal control is applied to a single-phase
voltage source inverter and validated with the experiment results. The
experiments show that the inverter supplies stable 60Hz 110V AC
power with a total harmonic distortion of less than 1%, under the DC
input variation from 190 V to 300 V and the output power variation
from 0 to 600 W.
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: In this research, a mathematical model for integrated evaluation of green design and green manufacturing processes is presented. To design a product, there can be alternative options to design the detailed components to fulfill the same product requirement. In the design alternative cases, the components of the product can be designed with different materials and detailed specifications. If several design alternative cases are proposed, the different materials and specifications can affect the manufacturing processes. In this paper, a new concept for integrating green design and green manufacturing processes is presented. A green design can be determined based the manufacturing processes of the designed product by evaluating the green criteria including energy usage and environmental impact, in addition to the traditional criteria of manufacturing cost. With this concept, a mathematical model is developed to find the green design and the associated green manufacturing processes. In the mathematical model, the cost items include material cost, manufacturing cost, and green related cost. The green related cost items include energy cost and environmental cost. The objective is to find the decisions of green design and green manufacturing processes to achieve the minimized total cost. In practical applications, the decision-making can be made to select a good green design case and its green manufacturing processes. In this presentation, an example product is illustrated. It shows that the model is practical and useful for integrated evaluation of green design and green manufacturing processes.
Abstract: Previous studies mass evacuation route network does
not fully reflect the step-by-step behavior and evacuees make routing
decisions. Therefore, they do not work as expected when applied to the
evacuation route planning is valid. This article describes where
evacuees may have to make a direction to select all areas were
identified as guiding points to improve evacuation routes network.
This improved route network can be used as a basis for the layout can
be used to guide the signs indicate that provides the required
evacuation direction. This article also describes that combines
simulation and artificial bee colony algorithm to provide the proposed
routing solutions, to plan an integrated routing mode. The improved
network and the model used is the cinema as a case study to assess the
floor. The effectiveness of guidance solution in the total evacuation
time is significant by verification.
Abstract: Baseball is unique among other sports in Taiwan.
Baseball has become a “symbol of the Taiwanese spirit and Taiwan-s
national sport". Taiwan-s first professional sports league, the Chinese
Professional Baseball League (CPBL), was established in 1989.
Starters pitch many more innings over the course of a season and for
a century teams have made all their best pitchers starters. In this
study, we attempt to determine the on-field performance these
pitchers and which won the most CPBL games in 2009. We utilize
the discriminate analysis approach to solve the problem, examining
winning pitchers and their statistics, to reliably find the best starting
pitcher. The data employed in this paper include innings pitched (IP),
earned runs allowed (ERA) and walks plus hits per inning pitched
(WPHIP) provided by the official website of the CPBL. The results
show that Aaron Rakers was the best starting pitcher of the CPBL.
The top 10 CPBL starting pitchers won 14 games to 8 games in the
2009 season. Though Fisher Discriminant Analysis, predicted to top
10 CPBL starting pitchers probably won 20 games to 9 games, more
1 game to 7 games in actually counts in 2009 season.
Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.