Abstract: This work is focused on the study of valuation of
recycled concrete aggregates, by measuring certain properties of
concrete in the fresh and hardened state. In this study, rheological
tests and physic-mechanical characterization on concretes and
mortars were conducted with recycled concrete whose geometric
properties were identified aggregates. Mortars were elaborated with
recycled fine aggregate (0/5mm) and concretes were manufactured
using recycled coarse aggregates (5/12.5 mm and 12.5/20 mm). First,
a study of the mortars was conducted to determine the effectiveness
of polycarboxylate superplasticizer on the workability of these and
their action deflocculating of the recycled sand. The rheological
behavior of mortars based on fine aggregate recycled was
characterized. The results confirm that the mortars composed of
different fractions of recycled sand (0 /5) have a better mechanical
properties (compressive and flexural strength) compared to normal
mortar. Also, the mechanical strengths of concretes made with
recycled aggregates (5/12.5 mm and 12.5/20 mm), are comparable to
those of conventional concrete with conventional aggregates,
provided that the implementation can be improved by the addition of
a superplasticizer.
Abstract: This review summarizes the potential of starch
agroindustrial residues as substrate for biohydrogen production.
Types of potential starch agroindustrial residues, recent developments
and bio-processing conditions for biohydrogen production will be
discussed. Biohydrogen is a clean energy source with great potential
to be an alternative fuel, because it releases energy explosively in
heat engines or generates electricity in fuel cells producing water as
only by-product. Anaerobic hydrogen fermentation or dark
fermentation seems to be more favorable, since hydrogen is yielded
at high rates and various organic waste enriched with carbohydrates
as substrate result in low cost for hydrogen production. Abundant
biomass from various industries could be source for biohydrogen
production where combination of waste treatment and energy
production would be an advantage. Carbohydrate-rich nitrogendeficient
solid wastes such as starch residues can be used for
hydrogen production by using suitable bioprocess technologies.
Alternatively, converting biomass into gaseous fuels, such as
biohydrogen is possibly the most efficient way to use these
agroindustrial residues.
Abstract: A modeling approach for CMOS gates is presented
based on the use of the equivalent inverter. A new model for the
inverter has been developed using a simplified transistor current
model which incorporates the nanoscale effects for the planar
technology. Parametric expressions for the output voltage are
provided as well as the values of the output and supply current to be
compatible with the CCS technology. The model is parametric
according the input signal slew, output load, transistor widths, supply
voltage, temperature and process. The transistor widths of the
equivalent inverter are determined by HSPICE simulations and
parametric expressions are developed for that using a fitting
procedure. Results for the NAND gate shows that the proposed
approach offers sufficient accuracy with an average error in
propagation delay about 5%.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: We propose a new alternative method for imposing
fluid-solid boundary conditions in simulations of Multiparticle
Collision Dynamics. Our method is based on the introduction of
an explicit potential force acting between the fluid particles and a
surface representing a solid boundary. We show that our method can
be used in simulations of plane Poiseuille flows. Important quantities
characterizing the flow and the fluid-solid interaction like the slip
coefficient at the solid boundary and the effective viscosity of the
fluid, are measured in terms of the set of independent parameters
defining the numerical implementation. We find that our method can
be used to simulate the correct hydrodynamic flow within a wide
range of values of these parameters.
Abstract: In the cloud computing hierarchy IaaS is the lowest
layer, all other layers are built over it. Thus it is the most important
layer of cloud and requisite more importance. Along with advantages
IaaS faces some serious security related issue. Mainly Security
focuses on Integrity, confidentiality and availability. Cloud
computing facilitate to share the resources inside as well as outside of
the cloud. On the other hand, cloud still not in the state to provide
surety to 100% data security. Cloud provider must ensure that end
user/client get a Quality of Service. In this report we describe
possible aspects of cloud related security.
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: The efficiency of wood vinegar mixed with each
individual of three plants extract such as: citronella grass
(Cymbopogon nardus), neem seed (Azadirachta indica A. Juss), and
yam bean seed (Pachyrhizus erosus Urb.) were tested against the
second instar larvae of housefly (Musca domestica L.). Steam
distillation was used for extraction of the citronella grass while neem
and yam bean were simple extracted by fermentation with ethyl
alcohol. Toxicity test was evaluated in laboratory based on two
methods of larvicidal bioassay: topical application method (contact
poison) and feeding method (stomach poison). Larval mortality was
observed daily and larval survivability was recorded until the
survived larvae developed to pupae and adults. The study resulted
that treatment of wood vinegar mixed with citronella grass showed
the highest larval mortality by topical application method (50.0%)
and by feeding method (80.0%). However, treatment of mixed wood
vinegar and neem seed showed the longest pupal duration to 25 day
and 32 days for topical application method and feeding method
respectively. Additional, larval duration on treated M. domestica
larvae was extended to 13 days for topical application method and 11
days for feeding method. Thus, the feeding method gave higher
efficiency compared with the topical application method.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: Nowadays, the Web has become one of the most
pervasive platforms for information change and retrieval. It collects
the suitable and perfectly fitting information from websites that one
requires. Data mining is the form of extracting data’s available in the
internet. Web mining is one of the elements of data mining
Technique, which relates to various research communities such as
information recovery, folder managing system and simulated
intellects. In this Paper we have discussed the concepts of Web
mining. We contain generally focused on one of the categories of
Web mining, specifically the Web Content Mining and its various
farm duties. The mining tools are imperative to scanning the many
images, text, and HTML documents and then, the result is used by
the various search engines. We conclude by presenting a comparative
table of these tools based on some pertinent criteria.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: Marine Protected Areas can benefit from nature based
tourism, monitoring environmental impacts and also become target
for human presence. From more than 3 million tourists visiting
Cozumel Island every year, an average of 2,8 million arrive by cruise
ship, and 41% are estimated to have motivation for water activities.
The destination is relying so much on the tourism activity, that scuba
diving and snorkeling in the National Park Reef of Cozumel sustain
the major economic activity. In order to achieve the sustainable
development indicator designed for regional environmental
development, the PNAC offers a training course to tourism providers
to access the protected area. This way, the update of the last 5 years
of such training is directed to diving staff, boat crew and
professionals, making them able to assist in managing the natural
resource. Moreover, the case study is an example to be used for
raising awareness among tourists visiting protected areas.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: The power converter that feeds high-frequency, highvoltage
transformers must be carefully designed due to parasitic
components, mainly the secondary winding capacitance and the
leakage inductance, that introduces resonances in relatively lowfrequency
range, next to the switching frequency. This paper
considers applications in which the load (resistive) has an
unpredictable behavior, changing from open to short-circuit condition
faster than the output voltage control loop could react. In this context,
to avoid overvoltage and over current situations, that could damage
the converter, the transformer or the load, it is necessary to find an
operation point that assure the desired output voltage in spite of the
load condition. This can done adjusting the frequency response of the
transformer adding an external inductance, together with selecting the
switching frequency to get stable output voltage independently of the
load.
Abstract: The operation of nuclear power plants involves
continuous monitoring of the environment in their area. This
monitoring is performed using a complex data acquisition system,
which collects status information about the system itself and values
of many important physical variables e.g. temperature, humidity,
dose rate etc. This paper describes a proposal and optimization of
communication that takes place in teledosimetric system between the
central control server responsible for the data processing and storing
and the decentralized measuring stations, which are measuring the
physical variables. Analyzes of ongoing communication were
performed and consequently the optimization of the system
architecture and communication was done.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: The influence of three different types of halloysite
nanotubes (HNTs) with different dimensions, namely as camel lake
(CLA), Jarrahdale (JA) and Matauri Bay (MB), on their reinforcing
ability of ethylene propylene dine monomer (EPDM) were
investigated by varying the HNTs loading (from 0-15 phr).
Mechanical properties of the nanocomposites improved with addition
of all three HNTs, but CLA based nanocomposites exhibited a
significant enhancement compared to the other HNTs. For instance,
tensile properties of EPDM nanocomposites increased by 120%,
256% and 340% for MB, JA and CLA, respectively, with addition of
15 phr of HNTs. This could be due to the higher aspect ratio and
higher surface area of CLA compared to others. Scanning electron
microscopy (SEM) of nanocomposites at 15 phr of HNT loadings
showed low amounts of pulled-out nanotubes which confirmed the
presence of more embedded nanotubes inside the EPDM matrix, as
well as aggregates within the fracture surface of EPDM/HNT
nanocomposites