Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: Arsenic in the sediments of the ash lagoons of the coal-fired power plant in Pagbilao, Quezon Province in the Philippines was sequentially extracted to determine its potential for leaching to the groundwater and the adjacent marine environment. Results show that 89% of the As is bound to the quasi-crystalline Fe/Mn oxides and hydroxide matrix in the sediments, whereas, the adsorbed and exchangeable As hosted by the clay minerals, representing those that are easiest to release from the sediment matrix, is below 10% of the acid leachable As. These As in these sediment matrices represent the possible maximum amount of As that can be released and supplied to the groundwater and the adjacent marine environment. Of the 89% reducible As, up to 4% is associated with the easily reducible variety, whereas, the rest is more strongly bonded by the moderately reducible variety. Based on the long-term As content of the lagoon water, the average desorption rate of As is calculated to be very low -- 0.3-0.5% on the average and 0.6% on the maximum. This indicates that As is well-fixed by its sediment matrices in the ash lagoon, attenuating the influx of As into the adjacent groundwater and marine environments.
Abstract: This paper presents the application of discrete-time
variable structure control with sliding mode based on the 'reaching
law' method for robust control of a 'simple inverted pendulum on
moving cart' - a standard nonlinear benchmark system. The
controllers designed using the above techniques are completely
insensitive to parametric uncertainty and external disturbance. The
controller design is carried out using pole placement technique to find
state feedback gain matrix , which decides the dynamic behavior
of the system during sliding mode. This is followed by feedback gain
realization using the control law which is synthesized from 'Gao-s
reaching law'. The model of a single inverted pendulum and the
discrete variable structure control controller are developed, simulated
in MATLAB-SIMULINK and results are presented. The response of
this simulation is compared with that of the discrete linear quadratic
regulator (DLQR) and the advantages of sliding mode controller over
DLQR are also presented
Abstract: We successfully developed and tested a new
separation layer solving problems with unmanageable deposits inside the boilers of Zluticka Heating Plant. The deposits are mainly created
by glass-forming melts. We plotted straw ash compositions in K2OCaO-
SiO2 phase diagram and illustrated that they are in the area of low-melting eutectic points. To prevent the melting of ash and the
formation of deposits, we modified ash compositions by injecting additives into biomass fuel, and thus effectively suppressed deposits in a burner.
Abstract: The purpose of this paper is to summarize the
following protection of scouring countermeasures by using
Bentonite-Enhanced Sand (BES) mixtures. The concept of
underground improvement is being used in this study to reduce the
void of the sand. The sand bentonite mixture was used to bond the
ground soil conditions surrounding the pile of integral bridge. The
right composition of sand bentonite mixture was proposed based on
previous findings. The swelling effect of bentonite also was
investigated to ensure there is no adverse impact to the structure of
the integral bridge. ScourScour, another name for severe erosion,
occurs when the erosive capacity of water resulting from natural and
manmade events exceeds the ability of earth materials to resist its
effects. According to AASHTO LRFD Specifications (Section
C3.7.5), scour is the most common reason for the collapse of
highway bridges in the United States
Abstract: This paper propose a new circuit design which
monitor total leakage current during standby mode and generates the
optimal reverse body bias voltage, by using the adaptive body bias
(ABB) technique to compensate die-to-die parameter variations.
Design details of power monitor are examined using simulation
framework in 65nm and 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 10 μW for 32nm technology and
about 12 μW for 65nm technology at the same power supply voltage
as the core power supply. Moreover the results show that our
proposed circuit design is not far sensitive to the temperature
variations and also process variations. Besides, uses the simple
blocks which offer good sensitivity, high speed, the continuously
feedback loop.
Abstract: The agricultural organic farming is different from
conventional farming in a way that is aimed at providing a balanced
and constructive action in agricultural systems. With the increase in
intensive agriculture, undesirable changes were being observed in
ecosystems with irreparable damage being caused to the natural
equilibrium. This is the reason for the increasing interest in organic
farming as an environment friendly agricultural production method.
In the present work three red fruits produced in organic farming were
analyzed, namely raspberry, gooseberry and blueberry. The samples
were harvested in a local farm when at plain maturation. The results
obtained allowed to conclude that the blueberry contained higher
amounts of phenolic compounds, total tannins and total anthocyanins
than raspberry and gooseberry. Furthermore, the HPLC analysis
allowed to identify monomeric anthocyanins and phenolic acids in
the three fruits studied.
Abstract: A automatic human tracking system using mobile
agent technology is realized because a mobile agent moves in
accordance with a migration of a target person. In this paper, we
propose a method for determining the neighbor node in consideration
of the imaging range of cameras.
Abstract: We have modeled the effect of a graded band gap
window on the performance of a single junction AlxGa1-xAs/GaAs
solar cell. First, we study the electrical characteristics of a single
junction AlxGa1-xAs/GaAs solar cell, by employing an optimized
structure for this solar cell, we show that grading the band gap of the
window can increase the conversion efficiency of the solar cell by
about 1.5%, and can also improve the quantum efficiency of the solar
cell especially at shorter wavelengths.
Abstract: Wireless capsule endoscopy provides real-time images in the digestive tract. Capsule images are usually low resolution and are diverse images due to travel through various regions of human body. Color information has been a primary reference in predicting abnormalities such as bleeding. Often color is not sufficient for this purpose. In this study, we took morphological shapes into account as additional, but important criterion. First, we processed gastric images in order to indentify various objects in the image. Then, we analyzed color information in the object. In this way, we could remove unnecessary information and increase the accuracy. Compared to our previous investigations, we could handle images of various degrees of brightness and improve our diagnostic algorithm.
Abstract: Multiple-Input-Multiple-Output (MIMO) is one of the most important communication techniques that allow wireless systems to achieve higher data rate. To overcome the practical difficulties in implementing Dirty Paper Coding (DPC), various suboptimal MIMO Broadcast (MIMO-BC) scheduling algorithms are employed which choose the best set of users among all the users. In this paper we discuss such a sub-optimal MIMO-BC scheduling algorithm which employs antenna selection at the receiver side. The channels for the users considered here are not Identical and Independent Distributed (IID) so that users at the receiver side do not get equal opportunity for communication. So we introduce a method of applying weights to channels of the users which are not IID in such a way that each of the users gets equal opportunity for communication. The effect of weights on overall sum-rate achieved by the system has been investigated and presented.
Abstract: The authors present an optimization algorithm for order reduction and its application for the determination of the relative mapping errors of linear time invariant dynamic systems by the simplified models. These relative mapping errors are expressed by means of the relative integral square error criterion, which are determined for both unit step and impulse inputs. The reduction algorithm is based on minimization of the integral square error by particle swarm optimization technique pertaining to a unit step input. The algorithm is simple and computer oriented. It is shown that the algorithm has several advantages, e.g. the reduced order models retain the steady-state value and stability of the original system. Two numerical examples are solved to illustrate the superiority of the algorithm over some existing methods.
Abstract: This paper is on the general discussion of memory consistency model like Strict Consistency, Sequential Consistency, Processor Consistency, Weak Consistency etc. Then the techniques for implementing distributed shared memory Systems and Synchronization Primitives in Software Distributed Shared Memory Systems are discussed. The analysis involves the performance measurement of the protocol concerned that is Multiple Writer Protocol. Each protocol has pros and cons. So, the problems that are associated with each protocol is discussed and other related things are explored.
Abstract: Atrazine, a herbicide widely used in sugarcane and corn production, is a frequently detected groundwater contaminant. An atrazine-degrading bacterium, strain KB02, was obtained from long-term atrazine-treated sugarcane field soils in Kanchanaburi province of Thailand. Strain KB02 had a rod-to-coccus morphological cycle during growth. Sequence analysis of the PCR product indicated that the 16S rRNA gene in strain KB02 was ranging from 97-98% identical to the same region in Klebsiella sp. Based on biochemical, physiological analysis and 16S rDNA sequence analysis of one representative isolate, strain KB02, the isolates belong to the genus Klebsiella in the family Enterobacteriaceae. Interestingly that the various primers for atzA, B and C failed to amplify genomic DNA of strain KB02. Whereas the expected PCR product of atzA, B and C were obtained from the reference strain, Arthrobacter sp. strain KU001.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and cvazistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine 1st stage nozzle blade
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: Grobner basis calculation forms a key part of computational
commutative algebra and many other areas. One important
ramification of the theory of Grobner basis provides a means to solve
a system of non-linear equations. This is why it has become very
important in the areas where the solution of non-linear equations is
needed, for instance in algebraic cryptanalysis and coding theory. This
paper explores on a parallel-distributed implementation for Grobner
basis calculation over GF(2). For doing so Buchberger algorithm is
used. OpenMP and MPI-C language constructs have been used to
implement the scheme. Some relevant results have been furnished
to compare the performances between the standalone and hybrid
(parallel-distributed) implementation.
Abstract: Banana is one of the most consumed fruits in the tropics and subtropics. Brazil accounts for about 9% of the world banana production. However, the production losses are as high as 30 to 40% and even much higher in some developing countries. The green banana flour is a complex carbohydrate source, including a high total starch (73.4%), resistant starch (17.5%) with functional properties. Gamma irradiation is considered to be an alternative method for food preservation. It has been performed due to the need of extending the shelf - life of foods, whilst maintaining their safety and avoiding one of the main concerns: the nutrient loss. In this work data about on the effects of ionizing radiation on the physicochemical analysis (carbohydrate, proteins, lipids, alimentary fiber, moistures and ashes) of Brazilian functional products (biscuits and bread) of the green banana pulp are presented. The caloric value was calculated. No significant difference was observed between the samples of irradiated and non – irradiated green banana biscuits with the following determinations: carbohydrates, proteins, alimentary fiber and ashes. Only a small significant difference was found in lipids (macronutrients). The results of physical chemical analysis of the irradiated and non- irradiated green banana bread non- irradiated showed no significant difference with the following determinations: carbohydrates, lipids (macronutrients), moisture, ashes and caloric value. A small difference was found in proteins (macronutrients). Irradiation of functional products (biscuits and bread) with doses of 1 and 3kGy maintained their original macronutrients content, showing good radioresistance.
Abstract: Steady state experiments have been conducted for
natural and mixed convection heat transfer, from five different sized
protruding discrete heat sources, placed at the bottom position on a
PCB and mounted on a vertical channel. The characteristic length (
Lh ) of heat sources vary from 0.005 to 0.011 m. The study has been
done for different range of Reynolds number and modified Grashof
number. From the experiment, the surface temperature distribution
and the Nusselt number of discrete heat sources have been obtained
and the effects of Reynold number and Richardson number on them
have been discussed. The objective is to find the rate of heat
dissipation from heat sources, by placing them at the bottom position
on a PCB and to compare both modes of cooling of heat sources.
Abstract: Microstructure, wetting behavior and interfacial
reactions between Sn–0.7Cu and Sn–0.3Ag–0.7Cu (SAC0307)
solders solidified on Ni coated Al substrates were compared and
investigated. Microstructure of Sn–0.7Cu alloy exhibited a eutectic
matrix composed of primary β-Sn dendrites with a fine dispersion of
Cu6Sn5 intermetallics whereas microstructure of SAC0307 alloy
exhibited coarser Cu6Sn5 and finer Ag3Sn precipitates of IMCs with
decreased tin dendrites. Contact angles ranging from 22° to 26° were
obtained for Sn–0.7Cu solder solidified on substrate surface whereas
for SAC0307 solder alloy contact angles were found to be in the
range of 20° to 22°. Sn–0.7Cu solder/substrate interfacial region
exhibited faceted (Cu, Ni)6Sn5 IMCs protruding into the solder matrix
and a small amount of (Cu, Ni)3Sn4 intermetallics at the interface.
SAC0307 solder/substrate interfacial region showed mainly (Cu,
Ni)3Sn4 intermetallics adjacent to the coating layer and (Cu,
Ni)6Sn5 IMCs in the solder matrix. The improvement in the
wettability of SAC0307 solder alloy on substrate surface is attributed
to the formation of cylindrical shape (Cu,Ni)6Sn5 and a layer of
(Cu, Ni)3Sn4 IMCs at the interface.