Abstract: Tsunami and inundation modelling due to far field tsunami propagation in a limited area is a very challenging numerical task because it involves many aspects such as the formation of various types of waves and the irregularities of coastal boundaries. To compute the effect of far field tsunami and extent of inland inundation due to far field tsunami along the coastal belts of west coast of Malaysia and Southern Thailand, a formulated boundary condition and a moving boundary condition are simultaneously used. In this study, a boundary fitted curvilinear grid system is used in order to incorporate the coastal and island boundaries accurately as the boundaries of the model domain are curvilinear in nature and the bending is high. The tsunami response of the event 26 December 2004 along the west open boundary of the model domain is computed to simulate the effect of far field tsunami. Based on the data of the tsunami source at the west open boundary of the model domain, a boundary condition is formulated and applied to simulate the tsunami response along the coastal and island boundaries. During the simulation process, a moving boundary condition is initiated instead of fixed vertical seaside wall. The extent of inland inundation and tsunami propagation pattern are computed. Some comparisons are carried out to test the validation of the simultaneous use of the two boundary conditions. All simulations show excellent agreement with the data of observation.
Abstract: Sodium borosilicate glasses doped with different
content of NdF3 mol % have been prepared by rapid quenching
method. Ultrasonic velocities (both longitudinal and shear)
measurements have been carried out at room temperature and at
ultrasonic frequency of 4 MHz. Elastic moduli, Debye temperature,
softening temperature and Poisson's ratio have been obtained as a
function of NdF3 modifier content. Results showed that the elastic
moduli, Debye temperature, softening temperature and Poisson's ratio
have very slight change with the change of NdF3 mol % content.
Based on FTIR spectroscopy and theoretical (Bond compression)
model, quantitative analysis has been carried out in order to obtain
more information about the structure of these glasses. The study
indicated that the structure of these glasses is mainly composed of
SiO4 units with four bridging oxygens (Q4), and with three bridging
and one nonbridging oxygens (Q3).
Abstract: Makishima and Mackenzie model was used to
simulation of acoustic properties (longitudinal and shear ultrasonic
wave velocities, elastic moduli theoretically for many tellurite and
borate glasses. The model was proposed mainly depending on the
values of the experimentally measured density, which are obtained
before. In this search work, we are trying to obtain the values of
densities of amorphous glasses (as the density depends on the
geometry of the network structure of these glasses). In addition, the
problem of simulating the slope of linear regression between the
experimentally determined bulk modulus and the product of packing
density and experimental Young's modulus, were solved in this
search work. The results showed good agreement between the
experimentally measured values of densities and both ultrasonic wave
velocities, and those theoretically determined.
Abstract: To focus on the vibration mode of a cone loudspeaker,
which acts as an electroacoustic transducer, excitation experiments
were performed using two types of loudspeaker units: one employing
an impulse hammer and the other a sweep signal. The on-axis sound
pressure frequency properties of the loudspeaker were evaluated, and
the characteristic properties of the loudspeakers were successfully
determined in both excitation experiments. Moreover, under
conditions identical to the experiment conditions, a coupled analysis of
the vibration-acoustics of the cone loudspeaker was performed using
an acoustic analysis software program that considers the impact of
damping caused by air viscosity. The result of sound pressure
frequency properties with the numerical analysis are the most closely
match that measured in the excitation experiments over a wide range
of frequency bands.
Abstract: At the Savonia University of Applied Sciences (UAS),
curriculum and studies have been improved by applying an Open
Innovation Space approach (OIS). It is based on multidisciplinary
action learning. The key elements of OIS-ideology are work-life
orientation, and student-centric communal learning. In this approach,
every participant can learn from each other and innovations will be
created. In this social innovation educational approach, all practices
are carried out in close collaboration with enterprises in real-life
settings, not in classrooms. As an example, in this paper, Savonia
UAS’s Future Food RDI hub (FF) shows how OIS practices are
implemented by providing food product development and consumer
research services for enterprises in close collaboration with
academicians, students and consumers. In particular one example of
OIS experimentation in the field is provided by a consumer research
carried out utilizing verbal analysis protocol combined with audiovisual
observation (VAP-WAVO). In this case, all co-learners were
acting together in supermarket settings to collect the relevant data for
a product development and the marketing department of a company.
The company benefitted from the results obtained, students were
more satisfied with their studies, educators and academicians were
able to obtain good evidence for further collaboration as well as
renewing curriculum contents based on the requirements of working
life. In addition, society will benefit over time as young university
adults find careers more easily through their OIS related food science
studies. Also this knowledge interaction model re-news education
practices and brings working-life closer to educational research
institutes.
Abstract: In this paper, a modified Wilkinson power divider for
GSM application is presented. The quarter–wavelength microstrip
lines in the conventional Wilkinson power divider (WPD) are
replaced by one-eighth wavelength transmission line. Wilkinson
power divider is designed using λ/4 and λ/8 transmission line. It has
the operating frequency of 915 MHz which is used in the GSM
standard. The proposed Wilkinson Power Divider is designed using
the simulation tool Advanced Design System. The results of λ/8
transmission line are very close to the results of λ/4 transmission line.
The isolation loss of λ/8 transmission line is improved by introducing
a capacitor between the output ports. The proposed Wilkinson power
divider has the best return loss of greater than -10 dB and isolation
loss of -15.25 dB. The λ/8 transmission line Wilkinson power divider
has the reduced size of 53.9 percentages than λ/4 transmission line
WPD. The proposed design has simple structure, better isolation loss
and good insertion loss.
Abstract: Weak damping of low frequency oscillations is a frequent phenomenon in electrical power systems. These frequencies can be damped by power system stabilizers. Unified power flow controller (UPFC), as one of the most important FACTS devices, can be applied to increase the damping of power system oscillations and the more effect of this controller on increasing the damping of oscillations depends on its proper placement in power systems. In this paper, a technique based on controllability is proposed to select proper location of UPFC and the best input control signal in order to enhance damping of power oscillations. The effectiveness of the proposed technique is demonstrated in IEEE 9 bus power system.
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: Manufacturing process has been considered as one of
the most important activity in business process. It correlates with
productivity and quality of the product so industries could fulfill
customer’s demand. With the increasing demand from customer,
industries must improve their manufacturing ability such as shorten
lead-time and reduce wastes on their process. Lean manufacturing
has been considered as one of the tools to waste elimination in
manufacturing or service industry. Workforce development is one
practice in lean manufacturing that can reduce waste generated from
operator such as waste of unnecessary motion. Anthropometric
approach is proposed to determine the recommended measurement in
operator’s work area. The method will get some dimensions from
Indonesia people that related to piston workstation. The result from
this research can be obtained new design for the work area
considering ergonomic aspect.
Abstract: A Reconfigurable Wilkinson power divider is
proposed in this paper. In existing system only a limited number of
bandwidth is used at the output ports, in the proposed Wilkinson
power divider different band of frequencies are obtained by using
PIN diode. By tuning the PIN diode, different frequencies are
achieved. The size of the power divider is reduced for the operating
frequency and increases the fractional bandwidth.
Abstract: In the present research, whole meal barley flour
(WBF) was supplemented with gelatinized corn flour (GCF) in 0 and
30%. Whole meal wheat flour (WWF) was mixed with defatted rice
bran (DRB) to produce 0, 20, 25, and 30% replacement levels.
Rheological properties of dough were studied. Thermal properties
and starch crystallinity of flours were evaluated. Flat bread, balady
bread and pie were prepared from the different flour blends. The
different bakeries were sensory evaluated. Color of raw materials and
crust of bakery products were determined. Nutrients contents of raw
flours and food products were assessed. Results showed that addition
of GCF to WBF increased the viscosity and falling number of the
produced dough. Water absorption, dough development time and
dough stability increased with increasing the level of DRB in dough
while, weakening and mixing tolerance index decreased.
Extensibility and energy decreased, while, resistance to extension
increased as DRB level increased. Gelatinized temperature of WWF,
WBF, GCF, and DRB were 13.26, 35.09, 28.33, and 39.63,
respectively. Starch crystallinity was affected when DRB was added
to WWF. The highest protein content was present in balady bread
made from 70% WWF and 30% DRB. The highest calcium,
phosphorus, and potassium levels were present in products made
from 100% WBF. Sensory attributes of the products were slightly
affected by adding DRB and GCF. Conclusion: Addition of DRB or
GCF to WWF or WBF, respectively affect the physical, chemical,
rheological and sensory properties of balady bread, flat bread, and pie
while improved their nutritive values.
Abstract: The present research aimed at studying the awareness
and attitudes of teachers towards inclusive education. The sample
consisted of 60 teachers, teaching in the primary section (1st – 4th) of
regular schools affiliated to the SSC board in Mumbai. Sample was
selected by Multi-stage cluster sampling technique. A semi-structured
self-constructed interview schedule and a self-constructed attitude
scale was used to study the awareness of teachers about disability and
Inclusive education, and their attitudes towards inclusive education
respectively. Themes were extracted from the interview data and
quantitative data was analyzed using SPSS package. Results revealed
that teachers had some amount of awareness but an inadequate
amount of information on disabilities and inclusive education.
Disability to most (37) teachers meant “an inability to do something”.
The difference between disability and handicap was stated by most as
former being cognitive while handicap being physical in nature. With
regard to Inclusive education, a large number (46) stated that they
were unaware of the term and did not know what it meant. Majority
(52) of them perceived maximum challenges for themselves in an
inclusive set up, and emphasized on the role of teacher training
courses in the area of providing knowledge (49) and training in
teaching methodology (53). Although, 83.3% of teachers held a
moderately positive attitude towards inclusive education, a large
percentage (61.6%) of participants felt that being in inclusive set up
would be very challenging for both children with special needs and
without special needs. Though, most (49) of the teachers stated that
children with special needs should be educated in regular classroom
but they further clarified that only those should be in a regular
classroom who have physical impairments of mild or moderate
degree.
Abstract: In the vicinity of red sea about 15 fungi species were
isolated from oil contaminated sites. On the basis of aptitude to
degrade the crude oil and DCPIP assay, two fungal isolates were
selected amongst 15 oil degrading strains. Analysis of ITS-1, ITS-2
and amplicon pyrosequencing studies of fungal diversity revealed
that these strains belong to Penicillium and Aspergillus species. Two
strains that proved to be the most efficient in degrading crude oil was
Aspergillus niger (54%) and Penicillium commune (48%) Subsequent
to two weeks of cultivation in BHS medium the degradation rate
were recorded by using spectrophotometer and GC-MS. Hence, it is
cleared that these fungal strains has capability of degradation and can
be utilize for cleaning the Saudi Arabian environment.
Abstract: Machine visualization is an area of interest with fast
and progressive development. We present a method of machine
visualization which will be applicable in real industrial conditions
according to current needs and demands. Real factory data were
obtained in a newly built research plant. Methods described in this
paper were validated on a case study. Input data were processed and
the virtual environment was created. The environment contains
information about dimensions, structure, disposition, and function.
Hardware was enhanced by modular machines, prototypes, and
accessories. We added functionalities and machines into the virtual
environment. The user is able to interact with objects such as testing
and cutting machines, he/she can operate and move them. Proposed
design consists of an environment with two degrees of freedom of
movement. Users are in touch with items in the virtual world which
are embedded into the real surroundings. This paper describes development of the virtual environment. We
compared and tested various options of factory layout virtualization
and visualization. We analyzed possibilities of using a 3D scanner in
the layout obtaining process and we also analyzed various virtual
reality hardware visualization methods such as: Stereoscopic (CAVE)
projection, Head Mounted Display (HMD) and augmented reality
(AR) projection provided by see-through glasses.
Abstract: Anaerobic digestion is a well-known technique for
sustainable energy recovery from sewage sludge. However, sewage
sludge digestion is restricted due to certain factors. Pre-treatment
methods have been established in various publications as a promising
technique to improve the digestibility of the sewage sludge and to
enhance the biogas generated which can be used for energy recovery.
In this study, continuous flow microwave (MW) pre-treatment with
different intensities were compared by using 5 L semi-continuous
digesters at a hydraulic retention time of 27 days. We focused on the
effects of MW at different intensities on the sludge solubilization,
sludge digestibility, and biogas production of the untreated and MW
pre-treated sludge. The MW pre-treatment demonstrated an increase
in the ratio of soluble chemical oxygen demand to total chemical
oxygen demand (sCOD/tCOD) and volatile fatty acid (VFA)
concentration. Besides that, the total volatile solid (TVS) removal
efficiency and tCOD removal efficiency also increased during the
digestion of the MW pre-treated sewage sludge compared to the
untreated sewage sludge. Furthermore, the biogas yield also
subsequently increases due to the pre-treatment effect. A higher MW
power level and irradiation time generally enhanced the biogas
generation which has potential for sustainable energy recovery from
sewage treatment plant. However, the net energy balance tabulation
shows that the MW pre-treatment leads to negative net energy production.
Abstract: The analytical bright two soliton solution of the 3-
coupled nonlinear Schrödinger equations with variable coefficients in
birefringent optical fiber is obtained by Darboux transformation
method. To the design of ultra-speed optical devices, Soliton
interaction and control in birefringence fiber is investigated. Lax pair
is constructed for N coupled NLS system through AKNS method.
Using two-soliton solution, we demonstrate different interaction
behaviors of solitons in birefringent fiber depending on the choice of
control parameters. Our results shows that interactions of optical
solitons have some specific applications such as construction of logic
gates, optical computing, soliton switching, and soliton amplification
in wavelength division multiplexing (WDM) system.
Abstract: Heat treatable aluminum alloys such as 7075 and
7055, because of high strength and low density, are used widely in
aircraft industry. For best mechanical properties, T6 heat treatment
has recommended for this regards, but this temper treatment is
sensitive to corrosion induced and Stress Corrosion Cracking (SCC)
damage. For improving this property, the over-aging treatment (T7)
applies to this alloy, but it decreases the mechanical properties up to
30 percent. Hence, to increase the mechanical properties, without any
remarkable decrease in SCC resistant, Retrogression and Re-Aging
(RRA) heat treatment is used. This treatment performs in a relatively
short time. In this paper, the RRA heat treatment was applied to 7055
aluminum alloy and then effect of RRA time on the mechanical
properties of 7055 has been investigated. The results show that the
40-minute time is suitable time for retrogression of 7055 aluminum
alloy and ultimate strength increases up to 625MPa.
Abstract: Pure nickel coatings have been successfully
electrodeposited on copper substrates by the pulse plating technique.
The influence of current density, duty cycle and pulse frequency on
the surface morphology, crystal orientation, and microhardness was
determined. It was found that the crystallite size of the deposit
increases with increasing current density and duty cycle. The crystal
orientation progressively changed from a random texture at 1 A/dm2
to (200) texture at 10 A/dm2. Increasing pulse frequency resulted in
increased texture coefficient and peak intensity of (111) reflection.
An increase in duty cycle resulted in considerable increase in texture
coefficient and peak intensity of (311) reflection. Coatings obtained
at high current densities and duty cycle present a mixed morphology
of small and large grains. Maximum microhardness of 193 Hv was
achieved at 4 A/dm2, 10 Hz and duty cycle of 50%. Nickel coatings
with (200) texture are ductile while (111) texture improves the
microhardness of the coatings.
Abstract: CuO thin films were deposited by spray ultrasonic
pyrolysis with different precursor solution. Two staring solution slats
were used namely: copper acetate and copper chloride. The influence
of these solutions on CuO thin films proprieties of is instigated. The
X rays diffraction (XDR) analysis indicated that the films deposed
with copper acetate are amorphous however the films elaborated with
copper chloride have monoclinic structure. UV- Visible transmission
spectra showed a strong absorbance of the deposited CuO thin films
in the visible region. Electrical characterization has shown that CuO
thin films prepared with copper acetate have a higher electrical
conductivity.