Abstract: Nowadays, induction motors have a significant role in industries. Condition monitoring (CM) of this equipment has gained a remarkable importance during recent years due to huge production losses, substantial imposed costs and increases in vulnerability, risk, and uncertainty levels. Motor current signature analysis (MCSA) is one of the most important techniques in CM. This method can be used for rotor broken bars detection. Signal processing methods such as Fast Fourier transformation (FFT), Wavelet transformation and Empirical Mode Decomposition (EMD) are used for analyzing MCSA output data. In this study, these signal processing methods are used for broken bar problem detection of Mobarakeh steel company induction motors. Based on wavelet transformation method, an index for fault detection, CF, is introduced which is the variation of maximum to the mean of wavelet transformation coefficients. We find that, in the broken bar condition, the amount of CF factor is greater than the healthy condition. Based on EMD method, the energy of intrinsic mode functions (IMF) is calculated and finds that when motor bars become broken the energy of IMFs increases.
Abstract: The health of the journal bearings is very important in preventing unforeseen breakdowns in rotary machines, and poor lubrication is one of the most important factors for producing the bearing failures. Hydrodynamic lubrication (HL), mixed lubrication (ML), and boundary lubrication (BL) are three regimes of a journal bearing lubrication. This paper uses acoustic emission (AE) measurement technique to correlate features of the AE signals to the three lubrication regimes. The transitions from HL to ML based on operating factors such as rotating speed, load, inlet oil pressure by time domain and time-frequency domain signal analysis techniques are detected, and then metal-to-metal contacts between sliding surfaces of the journal and bearing are identified. It is found that there is a significant difference between theoretical and experimental operating values that are obtained for defining the lubrication regions.
Abstract: This paper presents the result of an experimental
investigation regarding the use of Fe2O3 nanoparticles added to
kerosene as a working fluid, under magnetic field for Copper
Oscillating Heat pipe with inclination angle of 0°(horizontal), 15°,
30°,45°, 60°,75° and 90° (vertical). The following were examined;
measure the temperature distribution and heat transfer rate on
Oscillating Heat Pipe (OHP), with magnetic field under different
angles. Results showed that the addition of Fe2O3 nanoparticles under
magnetic field improved thermal performance of OHP especially in
75°.
Abstract: Electrohydraulic servo system have been used in
industry in a wide number of applications. Its dynamics are highly
nonlinear and also have large extent of model uncertainties and
external disturbances. In this paper, a robust back-stepping control
(RBSC) scheme is proposed to overcome the problem of disturbances
and system uncertainties effectively and to improve the tracking
performance of EHS systems. In order to implement the proposed
control scheme, the system uncertainties in EHS systems are
considered as total leakage coefficient and effective oil volume. In
addition, in order to obtain the virtual controls for stabilizing system,
the update rule for the system uncertainty term is induced by
the Lyapunov control function (LCF). To verify the performance and
robustness of the proposed control system, computer simulation of
the proposed control system using Matlab/Simulink Software
is executed. From the computer simulation, it was found that the
RBSC system produces the desired tracking performance and has
robustness to the disturbances and system uncertainties of EHS
systems.
Abstract: Electrohydraulic servo system have been used in industry in a wide number of applications. Its dynamics are highly nonlinear and also have large extent of model uncertainties and external disturbances. In this paper, a robust back-stepping control (RBSC) scheme is proposed to overcome the problem of disturbances and system uncertainties effectively and to improve the tracking performance of EHS systems. In order to implement the proposed control scheme, the system uncertainties in EHS systems are considered as total leakage coefficient and effective oil volume. In addition, in order to obtain the virtual controls for stabilizing system, the update rule for the system uncertainty term is induced by the Lyapunov control function (LCF). To verify the performance and robustness of the proposed control system, computer simulation of the proposed control system using Matlab/Simulink Software is executed. From the computer simulation, it was found that the RBSC system produces the desired tracking performance and has robustness to the disturbances and system uncertainties of EHS systems.
Abstract: Cities expansion, urban travels increase, the
technology development, the automobile price cheapen, and the
families' income ascending cause the considerable increase in
automobile numbers of the city. This fact has led to the traffic
creation and the automobile parking site shortage in the city. Also in
Esfahan metropolis, the parking lots shortage has been the great
problem of this town; in addition, in designing and constructing of
the parking sites the traditional methods are utilized which do not
have a reasonable and optimized usage of the valuable urban lands. In
this article, by introducing the prefabricate mechanized parking
system which is inexpensive, simple and quick, and occupies very
small space, therefore provides the high content of parking site for
the cities, we can eliminate the parking space shortage difficulty of
the cities. The achieved results of this research represent that an
optimized utilization of the existent urban spaces for parking site
construction has not been accomplished. By employing the new
parking site technologies such as mechanization categorized parking
sites and the capacity prefabricate mechanized of each parking space
have become 8 multiples; in this case, the valuable urban lands can
be used in an optimized way.
Abstract: The proliferation of web application and the pervasiveness of mobile technology make web-based attacks even more attractive and even easier to launch. Web Application Firewall (WAF) is an intermediate tool between web server and users that provides comprehensive protection for web application. WAF is a negative security model where the detection and prevention mechanisms are based on predefined or user-defined attack signatures and patterns. However, WAF alone is not adequate to offer best defensive system against web vulnerabilities that are increasing in number and complexity daily. This paper presents a methodology to automatically design a positive security based model which identifies and allows only legitimate web queries. The paper shows a true positive rate of more than 90% can be achieved.
Abstract: This project aims to investigate the potential of
torrefaction to improve the properties of Malaysian palm kernel shell
(PKS) as a solid fuel. A study towards torrefaction of PKS was
performed under various temperature and residence time of 240, 260,
and 280oC and 30, 60, and 90 minutes respectively. The torrefied
PKS was characterized in terms of the mass yield, energy yield,
elemental composition analysis, calorific value analysis, moisture and
volatile matter contents, and ash and fixed carbon contents. The mass
and energy yield changes in the torrefied PKS were observed to
prove that the temperature has more effect compare to residence time
in the torrefaction process. The C content of PKS increases while H
and O contents decrease after torrefaction, which resulted in higher
heating value between 5 to 16%. Meanwhile, torrefaction caused the
ash and fixed carbon content of PKS to increase, and the moisture
and volatile matter to decrease.
Abstract: A biosensor based on glucose oxidase (GOx) immobilized onto nanoparticles zirconium oxide with polyethylene nanocomposite for glucose monitoring has been designed. The CTAB/PEG/ZrO2/GOx nanocomposite was deposited onto screen printed carbon paste (SPCE) electrode via spin coating technique. The properties of CTAB/PEG/ZrO2/GOx were study using scanning electron microscopy (SEM). The SPE modified with the CTAB/PEG/ZrO2/GOx showed electrocatalytical response to the oxidation of glucose when ferrocene carboxaldehyde was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). Several parameters such as working potential, effect of pH and effect of ZrO2/PEG layers that governed the analytical performance of the biosensor, have been studied. The biosensor was applied to detect glucose with a linear range of 0.4 to 2.0 mmol L−1 with good repetability and reproducibility.
Abstract: This paper aims to study decomposition behavior in
pyrolytic environment of four lignocellulosic biomass (oil palm shell,
oil palm frond, rice husk and paddy straw), and two commercial
components of biomass (pure cellulose and lignin), performed in a
thermogravimetry analyzer (TGA). The unit which consists of a
microbalance and a furnace flowed with 100 cc (STP) min-1 Nitrogen,
N2 as inert. Heating rate was set at 20⁰C min-1 and temperature
started from 50 to 900⁰C. Hydrogen gas production during the
pyrolysis was observed using Agilent Gas Chromatography Analyzer
7890A. Oil palm shell, oil palm frond, paddy straw and rice husk
were found to be reactive enough in a pyrolytic environment of up to
900°C since pyrolysis of these biomass starts at temperature as low as
200°C and maximum value of weight loss is achieved at about
500°C. Since there was not much different in the cellulose,
hemicelluloses and lignin fractions between oil palm shell, oil palm
frond, paddy straw and rice husk, the T-50 and R-50 values obtained
are almost similar. H2 productions started rapidly at this temperature
as well due to the decompositions of biomass inside the TGA.
Biomass with more lignin content such as oil palm shell was found to
have longer duration of H2 production compared to materials of high
cellulose and hemicelluloses contents.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: Achievement motivation is believed to promote
giftedness attracting people to invest in many programs to adopt
gifted students providing them with challenging activities.
Intellectual giftedness is founded on the fluid intelligence and
extends to more specific abilities through the growth and inputs from
the achievement motivation. Acknowledging the roles played by the
motivation in the development of giftedness leads to an effective
nurturing of gifted individuals. However, no study has investigated
the direct and indirect effects of the achievement motivation and
fluid intelligence on intellectual giftedness. Thus, this study
investigated the contribution of motivation factors to giftedness
development by conducting tests of fluid intelligence using Cattell
Culture Fair Test (CCFT) and analytical abilities using culture
reduced test items covering problem solving, pattern recognition,
audio-logic, audio-matrices, and artificial language, and self report
questionnaire for the motivational factors. A number of 180 highscoring
students were selected using CCFT from a leading university
in Malaysia. Structural equation modeling was employed using Amos
V.16 to determine the direct and indirect effects of achievement
motivation factors (self confidence, success, perseverance,
competition, autonomy, responsibility, ambition, and locus of
control) on the intellectual giftedness. The findings showed that the
hypothesized model fitted the data, supporting the model postulates
and showed significant and strong direct and indirect effects of the
motivation and fluid intelligence on the intellectual giftedness.
Abstract: Elliptic curve-based certificateless signature is slowly
gaining attention due to its ability to retain the efficiency of
identity-based signature to eliminate the need of certificate
management while it does not suffer from inherent private
key escrow problem. Generally, cryptosystem based on elliptic
curve offers equivalent security strength at smaller key sizes
compared to conventional cryptosystem such as RSA which
results in faster computations and efficient use of computing
power, bandwidth, and storage. This paper proposes to implement
certificateless signature based on bilinear pairing to
structure the framework of IKE authentication. In this paper,
we perform a comparative analysis of certificateless signature
scheme with a well-known RSA scheme and also present the
experimental results in the context of signing and verification
execution times. By generalizing our observations, we discuss the
different trade-offs involved in implementing IKE authentication
by using certificateless signature.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: The Resource-Constrained Project Scheduling
Problem (RCPSP) is concerned with single-item or small batch
production where limited resources have to be allocated to dependent
activities over time. Over the past few decades, a lot of work has
been made with the use of optimal solution procedures for this basic
problem type and its extensions. Brucker and Knust[1] discuss, how
timetabling problems can be modeled as a RCPSP. Authors discuss
high school timetabling and university course timetabling problem as
an example. We have formulated two mathematical formulations of
course timetabling problem in a new way which are the prototype of
single-mode RCPSP. Our focus is to show, how course timetabling
problem can be transformed into RCPSP. We solve this
transformation model with genetic algorithm.
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.