Abstract: This paper applies recursive cointegration analysis to
examine the dynamic changes in Feldstein-Horioka saving-investment
(S-I) coefficients across China and the ASEAN-5 countries over time.
To the extent that the S-I coefficients measure international capital
mobility, the main empirical results are as follows. The recursive trace
statistics show that the investment- savings nexus varies in these six
countries. There is no cointegration between investment and savings in
three countries (China, Malaysia, and Singapore), which means that
the mobility of the capital markets in the three is high and that
domestic investment in them will be financed by the global pool of
capital. As to the other three countries (Indonesia, Thailand, and
Philippines), there is cointegration between investment and savings for
part of the sample period in the three, including before 2002 for
Thailand, before 2001 for Indonesia, and before 2002 for Philippines.
This shows these three countries achieved highly mobile and open
capital markets later.
Abstract: This paper presents the performance characteristics of
Darrieus-type vertical axis wind turbine (VAWT) with NACA airfoil
blades. The performance of Darrieus-type VAWT can be
characterized by torque and power. There are various parameters
affecting the performance such as chord length, helical angle, pitch
angle and rotor diameter. To estimate the optimum shape of Darrieustype
wind turbine in accordance with various design parameters, we
examined aerodynamic characteristics and separated flow occurring
in the vicinity of blade, interaction between flow and blade, and
torque and power characteristics derived from it. For flow analysis,
flow variations were investigated based on the unsteady RANS
(Reynolds-averaged Navier-Stokes) equation. Sliding mesh algorithm
was employed in order to consider rotational effect of blade. To
obtain more realistic results we conducted experiment and numerical
analysis at the same time for three-dimensional shape. In addition,
several parameters (chord length, rotor diameter, pitch angle, and
helical angle) were considered to find out optimum shape design and
characteristics of interaction with ambient flow. Since the NACA
airfoil used in this study showed significant changes in magnitude of
lift and drag depending on an angle of attack, the rotor with low drag,
long cord length and short diameter shows high power coefficient in
low tip speed ratio (TSR) range. On the contrary, in high TSR range,
drag becomes high. Hence, the short-chord and long-diameter rotor
produces high power coefficient. When a pitch angle at which airfoil
directs toward inside equals to -2° and helical angle equals to 0°,
Darrieus-type VAWT generates maximum power.
Abstract: Microstructure and mechanical properties of AZ91D
Mg alloys for nonflammable use, containing Ca and Y, were
investigated in this study. Solid solution treatment of AZ91D Mg alloy
with Ca and Y was successfully conducted at 420oC and
supersaturated microstructure with almost all beta phases resolved into
matrix was obtained. After solid solution treatment, the alloy was
annealed at temperatures of 180 and 200oC for time intervals from 1
min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced from the
results as at the temperature of 200oC for 10 hrs. Hot rolling was also
carried out at 400oC by the reduction ratio of 0.6 through 5 passes
followed by recrystallization treatment. Tensile and compressive
properties were measured at room temperature on the specimens of
each process, i.e. as-cast, solution treatment, hot rolling, and
recrystallization.
Abstract: With the strengthened regulation on the mandatory use
of recycled aggregate, development of construction materials using
recycled aggregate has recently increased. This study aimed to secure
the performance of asphalt concrete mixture by developing
recycled-modified asphalt using recycled basalt aggregate from the
Jeju area. The strength of the basalt aggregate from the Jeju area used
in this study was similar to that of general aggregate, while the specific
surface area was larger due to the development of pores. Modified
asphalt was developed using a general aggregate-recycled aggregate
ratio of 7:3, and the results indicated that the Marshall stability
increased by 27% compared to that of asphalt concrete mixture using
only general aggregate, and the flow values showed similar levels.
Also, the indirect tensile strength increased by 79%, and the toughness
increased by more than 100%. In addition, the TSR for examining
moisture resistance was 0.95 indicating that the reduction in the
indirect tensile strength due to moisture was very low (5% level), and
the developed recycled-modified asphalt could satisfy all the quality
standards of asphalt concrete mixture.
Abstract: This paper proposes a method of learning topics for
broadcasting contents. There are two kinds of texts related to
broadcasting contents. One is a broadcasting script, which is a series of
texts including directions and dialogues. The other is blogposts, which
possesses relatively abstracted contents, stories, and diverse
information of broadcasting contents. Although two texts range over
similar broadcasting contents, words in blogposts and broadcasting
script are different. When unseen words appear, it needs a method to
reflect to existing topic. In this paper, we introduce a semantic
vocabulary expansion method to reflect unseen words. We expand
topics of the broadcasting script by incorporating the words in
blogposts. Each word in blogposts is added to the most semantically
correlated topics. We use word2vec to get the semantic correlation
between words in blogposts and topics of scripts. The vocabularies of
topics are updated and then posterior inference is performed to
rearrange the topics. In experiments, we verified that the proposed
method can discover more salient topics for broadcasting contents.
Abstract: Geological structure formed by volcanic activities shows polymorphic characteristics due to repeated cooling and hardening of lava. The Jeju region is showing polymorphic characteristics in which clinker layers are irregularly distributed along with vesicular basalt due to volcanic activities. Accordingly, resident damages and environmental disputes occur frequently in the Jeju region due to blasting. The purpose of this study is to develop a blast vibration equation considering the polymorphic characteristics of basaltic ground in Jeju. The blast vibration equation consists of a functional formula of the blasting vibration constant K that changes according to ground characteristics, and attenuation index n. The case study results in Jeju showed that if there are clinker layers, attenuation index n showed a distribution of -1.32~-1.81, whereas if there are no clinker layers, n was -2.79. Moreover, if there are no clinker layers, the frequency of blast vibration showed a high frequency band from 30Hz to 100Hz, while in rocks with clinker layers it showed a low frequency band from 10Hz to 20Hz.
Abstract: Objective: Acute coronary syndrome is a clinical
condition encompassing ST segments elevation myocardial
infraction, Non ST segment is elevation myocardial infraction and un
stable angina is characterized by ruptured coronary plaque, stress and
myocardial injury. Angina pectoris is a pressure like pain in the chest
that is induced by exertion or stress and relived with in the minute
after cessation of effort or using sublingual nitroglycerin. The present
research was undertaken to study the drug utilization pattern of
antiplatelet drugs for the ischemic heart disease in a tertiary care
hospital. Method: The present study is retrospective drug utilization
study and study period is 6months. The data is collected from the
discharge case sheet of general medicine department from medical
department Rajiv Gandhi institute of medical sciences, Kadapa. The
tentative sample size fixed was 250 patients. Out of 250 cases 19
cases was excluded because of unrelated data. Results: A total of 250
prescriptions were collected for the study according to the inclusion
criteria 233 prescriptions were diagnosed with ischemic heart disease
17 prescriptions were excluded due to unrelated information. out of
233 prescriptions 128 are male (54.9%) and 105 patients are were
female (45%). According to the gender distribution, the prevalence of
ischemic heart disease in males are 90 (70.31%) and females are 39
(37.1%). In the same way the prevalence of ischemic heart disease
along with cerebrovascular disease in males are 39 (29.6%) and
females are 66 (62.6%). Conclusion: We found that 94.8% of drug
utilization of antiplatelet drugs was achieved in the Rajiv Gandhi
institute of medical sciences, Kadapa from 2011-2012.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: This study evaluated to facilitate separation of ABS
plastics from other waste plastics by froth flotation after surface
hydrophilization of ABS with heat treatment. The mild heat treatment
at 100oC for 60s could selectively increase the hydrophilicity of the
ABS plastics surface (i.e., ABS contact angle decreased from 79o to
65.8o) among other plastics mixture. The SEM and XPS results of
plastic samples sufficiently supported the increase in hydrophilic
functional groups and decrease contact angle on ABS surface, after
heat treatment. As a result of the froth flotation (at mixing speed 150
rpm and airflow rate 0.3 L/min) after heat treatment, about 85% of
ABS was selectively separated from other heavy plastics with 100%
of purity. The effect of optimum treatment condition and detailed
mechanism onto separation efficiency in the froth floatation was also
investigated. This research is successful in giving a simple, effective,
and inexpensive method for ABS separation from waste plastics.
Abstract: This study investigated the effects of thermal
treatment on Tualang honey sample in terms of honey colour and
heat-induced small metabolites. The heating process was carried out
in a temperature controlled water batch at 90oC for 4 hours. The
honey samples were put in cylinder tubes with the dimension of 1 cm
diameter and 10 cm length for homogenous heat transfer. The results
found that the thermal treatment produced not only
hydroxylmethylfurfural, but also other harmful substances such as
phthalic anhydride and radiolytic byproducts. The degradation of
honey protein was due to the detection of free amino acids such as
cysteine and phenylalanine in heat-treated honey samples. Sugar
dehydration was also occurred because fragmented di-galactose was
identified based on the presence of characteristic ions in the mass
fragmentation pattern. The honey colour was found getting darker as
the heating duration was increased up to 4 hours. Approximately, 60
mm PFund of increment was noticed for the honey colour with the
colour change rate of 14.8 mm PFund per hour. Based on the
principal component analysis, the score plot clearly shows that the
chemical profile of Tualang honey was significantly altered after 2
hours of heating at 90oC.
Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: Since the advances in digital imaging technologies have led to
development of high quality digital devices, there are a lot of illegal copies
of copyrighted video content on the Internet. Also, unauthorized editing is
occurred frequently. Thus, we propose an editing prevention technique for
high-quality (HQ) video that can prevent these illegally edited copies from
spreading out. The proposed technique is applied spatial and temporal gradient
methods to improve the fidelity and detection performance. Also, the scheme
duplicates the embedding signal temporally to alleviate the signal reduction
caused by geometric and signal-processing distortions. Experimental results
show that the proposed scheme achieves better performance than previously
proposed schemes and it has high fidelity. The proposed scheme can be used
in unauthorized access prevention method of visual communication or traitor
tracking applications which need fast detection process to prevent illegally
edited video content from spreading out.
Abstract: When evaluating the capacity of a generation park to
cover the load in transmission systems, traditional Loss of Load
Expectation (LOLE) and Expected Energy not Served (EENS)
indices can be used. If those indices allow computing the annual
duration and severity of load non covering situations, they do not take
into account the fact that the load excess is generally shifted from one
penury state (hour or quarter of an hour) to the following one. In this
paper, a sequential Monte Carlo framework is introduced in order to
compute adjusted LOLE and EENS indices. Practically, those
adapted indices permit to consider the effect of load excess transfer
on the global adequacy of a generation park, providing thus a more
accurate evaluation of this quantity.
Abstract: This study focuses on the stress analysis of Mandibular
Advancement Devices (MADs), which are considered as a standard
treatment of snoring that promoted by American Academy of Sleep
Medicine (AASM). Snoring is the most significant feature of
sleep-disordered breathing (SDB). SDB will lead to serious problems
in human health. Oral appliances are ensured in therapeutic effect and
compliance, especially the MADs. This paper proposes a new MAD
design, and the finite element analysis (FEA) is introduced to precede
the stress simulation for this MAD.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: Durian skin is a newly explores natural fibre
potentially reinforced polyolefin for diverse applications. In this
work, investigation on the effect of coupling agent, maleic anhydride
polypropylene (MAPP) on the mechanical, morphological, and
thermal properties of polypropylene (PP) reinforced with durian skin
fibre (DSF) was conducted. The presence of 30 wt% DSF
significantly reduced the tensile strength of PP-DSF composite.
Interestingly, even though the same trend goes to PP-DSF with the
presence of MAPP, the reduction is only about 4% relative to
unreinforced PP and 18% higher than PP-DSF without MAPP
(untreated composite or UTC). The used of MAPP in treated
composite (TC) also increased the tensile modulus, flexural
properties and degradation temperature. The enhanced mechanical
properties are consistent with good interfacial interaction as
evidenced under scanning electron microscopy.
Abstract: This study identified the hypothesised relationship
between creative experience, and revisit intention of handmade
oriental parasol umbrella in Kaohsiung, Taiwan. A face-to-face
questionnaire survey was administered in Meinong town, Kaohsiung.
The components of creative experience were found as “sense of
achievement”, “unique learning” and “interaction with instructors” in
creative tourism. The result also revealed significant positive
relationships between creative experience and revisit intention in
handmade activities. This paper provides additional suggestions for
enhancing revisit intention and guidance regarding creative tourism.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).