Abstract: Combustion of fuels in industrial and transport sector has lead to an alarming release of polluting gases to the atmosphere. Carbon monoxide is one such pollutant, which is formed as a result of incomplete oxidation of the fuel. In order to analyze the effect of catalyst on the reduction of CO emissions to the atmosphere, two catalysts Mn2O3 and Hopcalite are considered. A model was formed based on mass and energy balance equations. Results show that Hopcalite catalyst as compared to Mn2O3 catalyst helped in faster conversion of the polluting gas as the operating temperature of the hopcalite catalyst is much lower as compared to the operating temperature of Mn2O3 catalyst.
Abstract: The reproductive aging of women is a biological process which is expressed by the loss of ovarian function and therefore the loss of the possibility of procreation. The present work aims to evaluate the effect of menopause on sexual health of rural women and to examine the determinants of female sexuality after menopause. A survey was conducted among 527 women in the rural area of Marrakech. The average age of women was 51.92 ± 7.24 years. It appears from this study that sexual activity in menopausal women decreases with age, 20% of women had no sexual activity after menopause. 72% of respondents reported having sex by obligation, 71% of women say they are not satisfied with their sexuality, while 29 % are very satisfied. The most common sexual complaints are represented by the decreased libido (81%), vaginal dryness (54%), and pain (22,7%). Of the 511 women with sexual dysfunction, only 34 (6, 4%) consulted for this disorder. Many factors may influence sex include menopause and all the biological changes but also the roles of culture, social constructions and perception of sexuality after menopause are complicated.
Abstract: In power system protection, the need to know the load
current together with the fault level detected by a relay is important.
This is due to the fact that the relay is required to isolate the
equipment being protected if a fault is present and keep the breaker
associated with it closed if the current level is lower than the
maximum load level. This is not an issue for a radial system. This is
not the same however in a looped power system. In a looped power
system, the isolation of an equipment system will contribute to a
topology change. The change in the power system topology will then
influence or change the maximum load current and the fault level
detected by each relay. In this paper, a method of data collection for
changing topology using matlab and sim-power will be presented.
The method will take into consideration the change in topology and
collect data for each possible topology.
Abstract: An optical chemical sensing film based on
immobilizing of 1,1′- diethyl 2,2′-cyanine (pseudocyanine iodide) in
nafion film was developed for the determination of Fe(III). The
sensing film was homogeneous, transparent, and mechanically stable.
Decrease of the absorbance measured at 518 nm was observed when
the sensing film was immersed in a solution of Fe(III). The optimum
response of the sensing film to Fe(III) was obtained in a solution with
pH 4.0. Linear calibration curve over an Fe(III) concentration range
of 1-30 ppm with a limit of detection of 0.71 ppm was obtained.
Cd(II) is the major interference. The sensing film exhibited good
stability for 2 months and high reproducibility. The proposed method
was applied for the determination of Fe(III) in water samples with
satisfactory results.
Abstract: Image registration is the process of establishing point
by point correspondence between images obtained from a same
scene. This process is very useful in remote sensing, medicine,
cartography, computer vision, etc. Then, the task of registration is to
place the data into a common reference frame by estimating the
transformations between the data sets. In this work, we develop a
rigid point registration method based on the application of genetic
algorithms and Hausdorff distance. First, we extract the feature points
from both images based on the algorithm of global and local
curvature corner. After refining the feature points, we use Hausdorff
distance as similarity measure between the two data sets and for
optimizing the search space we use genetic algorithms to achieve
high computation speed for its inertial parallel. The results show the
efficiency of this method for registration of satellite images.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving large size set covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the set covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: Thermite welding is mainly used in world. The
reasons why the thermite welding method is widely used are
that the equipment has good mobility and total working time
of that is shorter than that of the enclosed arc welding method
on site. Moreover, the operating skill, which required for
thermite welding, is less than that of for enclosed arc welding.
In the present research work, heat treatment and combined
'expulsion and heat treatment' techniques were used improve
the mechanical properties and weldment structure. The
specimens were cut in the transverse direction from expulsion
with Heat treated and heat treated Thermite Welded rails.
Specimens were prepared according to AWS standard and
subjected to tensile test, Impact test and hardness and their
results were tabulated. Microstructural analysis was carried
out with the help of SEM. Then analyze to effect of heat
treated and 'expulsion with heat treated' with the properties of
their thermite welded rails. Compare the mechanical and
microstructural properties of thermite welded rails between
heat expulsion with heat treated and heat treated. Mechanical
and microstructural response expulsion with heat treated
thermite welded rail is higher value as compared to heat
treatment.
Abstract: This paper presents a new compact analytical model of
the gate leakage current in high-k based nano scale MOSFET by
assuming a two-step inelastic trap-assisted tunneling (ITAT) process
as the conduction mechanism. This model is based on an inelastic
trap-assisted tunneling (ITAT) mechanism combined with a semiempirical
gate leakage current formulation in the BSIM 4 model. The
gate tunneling currents have been calculated as a function of gate
voltage for different gate dielectrics structures such as HfO2, Al2O3
and Si3N4 with EOT (equivalent oxide thickness) of 1.0 nm. The
proposed model is compared and contrasted with santaurus
simulation results to verify the accuracy of the model and excellent
agreement is found between the analytical and simulated data. It is
observed that proposed analytical model is suitable for different highk
gate dielectrics simply by adjusting two fitting parameters. It was
also shown that gate leakages reduced with the introduction of high-k
gate dielectric in place of SiO2.
Abstract: Uniqueness and distinctiveness of localities (referred to as genius loci or sense of place) are important to ensure people-s identification with their locality. Existing frameworks reveals that the affective dimension of environments is rarely mentioned or explored and limited public participation was used in constructing the frameworks. This research argues that the complexity of sense of place would be recognised and appropriate planning guidelines formulated by exploring and integrating the affective dimension of a site. Aims of the research therefore are to (i) explore relational dimensions between people and a natural rural landscape, (ii) to implement a participatory approach to obtain insight into different relational dimensions, and (ii) to concretise socio-affective relational dimensions into site planning guidelines. A qualitative, interdisciplinary research approach was followed and conducted on the farm Kromdraai, Vredefort Dome World Heritage Site. In essence the first phase of the study reveals various affective responses and projections of personal meanings. The findings in phase 1 informed the second phase, to involve people from various disciplines and different involvement with the area to make visual presentations of appropriate planning and design of the site in order to capture meanings of the interactions between people and their environment. Final site planning and design guidelines were formulated, based on these. This research contributed to provide planners with new possibilities of exploring the dimensions between people and places as well as to develop appropriate methods for participation to obtain insight into the underlying meanings of sites.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: Electron back-scattered diffraction was used to follow the evolution of microstructure from the base metal to the stir zone (SZ) in a duplex stainless steel subjected to friction stir welding. In the stir zone (SZ), a continuous dynamic recrystallization (CDRX) was evidenced for ferrite, while it was suggested that a static recrystallization together with CDRX may occur for austenite. It was found that ferrite and austenite grains in the SZ take a typical shear texture of bcc and fcc materials respectively.
Abstract: Experimental investigation of heat transfer and
friction factor characteristics of circular tube fitted with 300 right-left helical screw inserts with 100 mm spacer of different twist ratio has
been presented for laminar and turbulent flow.. The experimental data obtained were compared with those obtained from plain tube
published data. The heat transfer coefficient enhancement for 300 RL
inserts with 100 mm spacer is quite comparable with for 300 R-L
inserts. Performance evaluation analysis has been made and found
that the performance ratio increases with increasing Reynolds number
and decreasing twist ration with the maximum for the twist ratio 2.93.
Also, the performance ratio of more than one indicates that the type
of twist inserts can be used effectively for heat transfer augmentation.
Abstract: We show that in a two-channel sampling series expansion
of band-pass signals, any finitely many missing samples can
always be recovered via oversampling in a larger band-pass region.
We also obtain an analogous result for multi-channel oversampling
of harmonic signals.
Abstract: Contact stress is an important problem in industry.
This is a problem that in the first attention may be don-t appears, but
disregard of these stresses cause a lot of damages in machines. These
stresses occur at locations such as gear teeth, bearings, cams and
between a locomotive wheel and the railroad rail. These stresses
cause failure by excessive elastic deformation, yielding and fracture.
In this paper we intend show the effective parameters in contact
stress and ponder effect of curvature. In this paper we study contact
stresses on the surface of gear teeth and compare these stresses for
four popular profiles of gear teeth (involute, cycloid, epicycloids, and
hypocycloid). We study this problem with mathematical and finite
element methods and compare these two methods on different profile
surfaces.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: Probiotic bacteria especially Lactobacillus spp. and Bifidobacterium exert suppressive effect on Helicobacter pylori. Cinnamon and licorice have been traditionally used for the treatment of gastric ulcer. The objectives of this study were to determine the effects of herbs on yogurt fermentation, the level of probiotic bacteria in yogurt during 28 days storage and the effect of herbal yogurt on the growth of H. pylori in vitro. Cinnamon or licorice was mixed with milk and the mixture was fermented with probiotic bacteria to form herbal-yogurt. Changes of pH and total titratable acids were monitored and the viability of probiotic bacteria was evaluated during and after refrigerated storage. The in vitro inhibition of H. pylori growth was determined using agar diffusion and minimum inhibitory concentration (MIC) method. The presence of herbs did not affect the probiotic population during storage. There were no significant differences in pH and TTA between herbal-yogurts and plain-yogurt during fermentation and storage. Water extract of cinnamon-yogurt showed the highest inhibition effect (13.5mm) on H. pylori growth in comparison with licorice-yogurt (11.2mm). The present findings indicate cinnamon and licorice has bioactive components to decrease the growth of H. pylori.
Abstract: Multi-Radio Multi-Channel (MRMC) systems are key to power control problems in wireless mesh networks (WMNs). In this paper, we present asynchronous multiple-state based power control for MRMC WMNs. First, WMN is represented as a set of disjoint Unified Channel Graphs (UCGs). Second, each network interface card (NIC) or radio assigned to a unique UCG adjusts transmission power using predicted multiple interaction state variables (IV) across UCGs. Depending on the size of queue loads and intra- and inter-channel states, each NIC optimizes transmission power locally and asynchronously. A new power selection MRMC unification protocol (PMMUP) is proposed that coordinates interactions among radios. The efficacy of the proposed method is investigated through simulations.
Abstract: The DNA microarray technology concurrently monitors the expression levels of thousands of genes during significant biological processes and across the related samples. The better understanding of functional genomics is obtained by extracting the patterns hidden in gene expression data. It is handled by clustering which reveals natural structures and identify interesting patterns in the underlying data. In the proposed work clustering gene expression data is done through an Advanced Nelder Mead (ANM) algorithm. Nelder Mead (NM) method is a method designed for optimization process. In Nelder Mead method, the vertices of a triangle are considered as the solutions. Many operations are performed on this triangle to obtain a better result. In the proposed work, the operations like reflection and expansion is eliminated and a new operation called spread-out is introduced. The spread-out operation will increase the global search area and thus provides a better result on optimization. The spread-out operation will give three points and the best among these three points will be used to replace the worst point. The experiment results are analyzed with optimization benchmark test functions and gene expression benchmark datasets. The results show that ANM outperforms NM in both benchmarks.
Abstract: In this work, sorption of nickel from aqueous solution on hypnea valentiae, red macro algae, was investigated. Batch experiments have been carried out to find the effect of various parameters such as pH, temperature, sorbent dosage, metal concentration and contact time on the sorption of nickel using hypnea valentiae. Response surface methodology (RSM) is employed to optimize the process parameters. Based on the central composite design, quadratic model was developed to correlate the process variables to the response. The most influential factor on each experimental design response was identified from the analysis of variance (ANOVA). The optimum conditions for the sorption of nickel were found to be: pH – 5.1, temperature – 36.8oC, sorbent dosage – 5.1 g/L, metal concentration – 100 mg/L and contact time – 30 min. At these optimized conditions the maximum removal of nickel was found to be 91.97%. A coefficient of determination R2 value 0.9548 shows the fitness of response surface methodology in this work.
Abstract: Total weighted tardiness is a measure of customer
satisfaction. Minimizing it represents satisfying the general
requirement of on-time delivery. In this research, we consider an ant
colony optimization (ACO) algorithm to solve the problem of
scheduling unrelated parallel machines to minimize total weighted
tardiness. The problem is NP-hard in the strong sense. Computational
results show that the proposed ACO algorithm is giving promising
results compared to other existing algorithms.