Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: An experimental and simulation flight test has been carried out to evaluate the longitudinal gliding characteristics of a lifting body with blunted half-cone geometry. The novelty here is the lifting body's pitch control mechanism, which consists of a pair of leading-edge rotating cylinders. Flight simulation uses aerodynamic data from computational fluid dynamics supported by wind-tunnel test. Flight test consists of releasing an aluminum lifting body model from a moving vehicle at the appropriate wind speed while measuring the lifting body's variation of altitude against time of flight. Results show that leading-edge rotating cylinder is able to give small amounts of improvement to the longitudinal stability and pitch control to the lifting body.
Abstract: The aim of this paper is to propose a mathematical
model to determine invariant sets, set covering, orbits and, in
particular, attractors in the set of tourism variables. Analysis was
carried out based on a pre-designed algorithm and applying our
interpretation of chaos theory developed in the context of General
Systems Theory. This article sets out the causal relationships
associated with tourist flows in order to enable the formulation of
appropriate strategies. Our results can be applied to numerous cases.
For example, in the analysis of tourist flows, these findings can be
used to determine whether the behaviour of certain groups affects that
of other groups and to analyse tourist behaviour in terms of the most
relevant variables. Unlike statistical analyses that merely provide
information on current data, our method uses orbit analysis to
forecast, if attractors are found, the behaviour of tourist variables in
the immediate future.
Abstract: With the globalized production and logistics
environment, the need for reducing the product development interval
and lead time, having a faster response to orders, conforming to quality
standards, fair tracking, and boosting information exchanging
activities with customers and partners, and coping with changes in the
management environment, manufacturers are in dire need of an
information management system in their manufacturing environments.
There are lots of information systems that have been designed to
manage the condition or operation of equipment in the field but
existing systems have a decentralized architecture, which is not
unified. Also, these systems cannot effectively handle the status data
extraction process upon encountering a problem related to protocols or
changes in the equipment or the setting. In this regard, this paper will
introduce a system for processing and saving the status info of
production equipment, which uses standard representation formats, to
enable flexible responses to and support for variables in the field
equipment. This system can be used for a variety of manufacturing and
equipment settings and is capable of interacting with higher-tier
systems such as MES.
Abstract: Early detection of lung cancer through chest radiography is a widely used method due to its relatively affordable cost. In this paper, an approach to improve lung nodule visualization on chest radiographs is presented. The approach makes use of linear phase high-frequency emphasis filter for digital filtering and
histogram equalization for contrast enhancement to achieve improvements. Results obtained indicate that a filtered image can
reveal sharper edges and provide more details. Also, contrast enhancement offers a way to further enhance the global (or local) visualization by equalizing the histogram of the pixel values within
the whole image (or a region of interest). The work aims to improve lung nodule visualization of chest radiographs to aid detection of lung cancer which is currently the leading cause of cancer deaths worldwide.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Water, soil and sediment contaminated with
metolachlor poses a threat to the environment and human health.
We determined the effectiveness of nano-zerovalent iron (NZVI) to
dechlorinate metolachlor [2-chloro-n-(2-ethyl-6-methyl-phenyl)-n-
(1-methoxypropan-2-yl)acetamide] in pH solution and the presence
of aluminium salt. The optimum dosage of degradation of 100 mlL-1
metolachlor was 1% (w/v) NZVI. The degradation kinetic rate (kobs)
was 0.218×10-3 min-1 and specific first-order rates (kSA) was
8.72×10-7 L m-2min-1. By treating aqueous solutions of metolachlor
with NZVI, metolachlor destruction rate were increased as the pH
decrease from 10 to 4. Lowering solution pH removes Fe (III)
passivating layers from the NZVI and makes it free for reductive
transformations. Destruction kinetic rates were 20.8×10-3 min-1 for
pH4, 18.9×10-3 min-1 for pH7, 13.8×10-3 min-1 for pH10. In addition,
destruction kinetic of metolachlor by NZVI was enhanced when
aluminium sulfate was added. The destruction kinetic rate were
20.4×10-3 min-1 for 0.05% Al(SO4)3 and 60×10-3 min-1 for 0.1%
Al(SO4)3.
Abstract: This paper addresses the problem of blind source separation
(BSS). To recover original signals, from linear instantaneous
mixtures, we propose a new contrast function based on the use of a
double referenced system. Our approach assumes statistical independence
sources. The reference vectors will be incrusted in the cumulant
to evaluate the independence. The estimation of the separating matrix
will be performed in two steps: whitening observations and joint
diagonalization of a set of referenced cumulant matrices. Computer
simulations are presented to demonstrate the effectiveness of the
suggested approach.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: This work is focused on the steady boundary layer flow
near the forward stagnation point of plane and axisymmetric bodies
towards a stretching sheet. The no slip condition on the solid
boundary is replaced by the partial slip condition. The analytical
solutions for the velocity distributions are obtained for the various
values of the ratio of free stream velocity and stretching velocity, slip
parameter, the suction and injection velocity parameter, magnetic
parameter and dimensionality index parameter in the series forms with
the help of homotopy analysis method (HAM). Convergence of the
series is explicitly discussed. Results show that the flow and the skin
friction coefficient depend heavily on the velocity slip factor. In
addition, the effects of all the parameters mentioned above were more
pronounced for plane flows than for axisymmetric flows.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: Since the feasibility study of R&D programs have been
initiated for efficient public R&D investments, year 2008, feasibility
studies have improved in terms of precision. Although experience
related to these studies of R&D programs have increased to a certain
point, still methodological improvement is required. The feasibility
studies of R&D programs are consisted of various viewpoints, such as
technology, policy, and economics. This research is to provide
improvement methods to the economic perspective; especially the cost
estimation process of R&D activities. First of all, the fundamental
concept of cost estimation is reviewed. After the review, a statistical
and econometric analysis method is applied as empirical analysis.
Conclusively, limitations and further research directions are provided.
Abstract: In this paper a unified approach via block-pulse functions (BPFs) or shifted Legendre polynomials (SLPs) is presented to solve the linear-quadratic-Gaussian (LQG) control problem. Also a recursive algorithm is proposed to solve the above problem via BPFs. By using the elegant operational properties of orthogonal functions (BPFs or SLPs) these computationally attractive algorithms are developed. To demonstrate the validity of the proposed approaches a numerical example is included.
Abstract: This paper presents a new technique for the optimum
placement of processors to minimize the total effective
communication load under multi-processor communication
dominated environment. This is achieved by placing heavily loaded
processors near each other and lightly loaded ones far away from
one another in the physical grid locations. The results are
mathematically proved for the Algorithms are described.
Abstract: High Voltage (HV) transmission lines are widely
spread around residential places. They take all forms of shapes:
concrete, steel, and timber poles. Earth grid always form part of the
HV transmission structure, whereat soil resistivity value is one of the
main inputs when it comes to determining the earth grid
requirements. In this paper, the soil structure and its implication on
the electrode resistance of HV transmission poles will be explored. In
Addition, this paper will present simulation for various soil structures
using IEEE and Australian standards to verify the computation with
CDEGS software. Furthermore, the split factor behavior under
different soil resistivity structure will be presented using CDEGS
simulations.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: There are two types of drought as conceptual drought
and operational drought. The three parameters as the beginning, the
end and the degree of severity of the drought can be identifying in
operational drought by average precipitation in the whole region. One
of the methods classified to measure drought is Reconnaissance
Drought Index (RDI). Evapotranspiration is calculated using
Penman-Monteith method by analyzing thirty nine years prolong
climatic data. The evapotranspiration is then utilized in RDI to
classify normalized and standardized RDI. These RDI classifications
led to what kind of drought faced in Bhavnagar region on 12 month
time scale basis. The comparison between actual drought conditions
and RDI method used to find out drought are also illustrated. It can
be concluded that the index results of drought in a particular year are
same in both methods but having different index values where as
severity remain same.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.
Abstract: The Artificial immune systems algorithms are Meta
heuristic optimization method, which are used for clustering and
pattern recognition applications are abundantly. These algorithms in
multimodal optimization problems are more efficient than genetic
algorithms. A major drawback in these algorithms is their slow
convergence to global optimum and their weak stability can be
considered in various running of these algorithms. In this paper,
improved Artificial Immune System Algorithm is introduced for the
first time to overcome its problems of artificial immune system. That
use of the small size of a local search around the memory antibodies
is used for improving the algorithm efficiently. The credibility of the
proposed approach is evaluated by simulations, and it is shown that
the proposed approach achieves better results can be achieved
compared to the standard artificial immune system algorithms
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is very important as it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, it helps to reduce the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we make a survey of the factors that influence exclusive breastfeeding and use two dispersed statistical models to analyze data. The models are the Generalized Poisson regression model and the Com-Poisson regression models.