Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: This paper presents the development and application of an adaptive neuro fuzzy inference system (ANFIS) based intelligent hybrid neuro fuzzy controller for automatic generation control (AGC) of two-area interconnected thermal power system with reheat non linearity. The dynamic response of the system has been studied for 1% step load perturbation in area-1. The performance of the proposed neuro fuzzy controller is compared against conventional proportional-integral (PI) controller, state feedback linear quadratic regulator (LQR) controller and fuzzy gain scheduled proportionalintegral (FGSPI) controller. Comparative analysis demonstrates that the proposed intelligent neuro fuzzy controller is the most effective of all in improving the transients of frequency and tie-line power deviations against small step load disturbances. Simulations have been performed using Matlab®.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: This paper addresses an efficient technique to embed and detect digital fingerprint code. Orthogonal modulation method is a straightforward and widely used approach for digital fingerprinting but shows several limitations in computational cost and signal efficiency. Coded modulation method can solve these limitations in theory. However it is difficult to perform well in practice if host signals are not available during tracing colluders, other kinds of attacks are applied, and the size of fingerprint code becomes large. In this paper, we propose a hybrid modulation method, in which the merits of or-thogonal modulation and coded modulation method are combined so that we can achieve low computational cost and high signal efficiency. To analyze the performance, we design a new fingerprint code based on GD-PBIBD theory and modulate this code into images by our method using spread-spectrum watermarking on frequency domain. The results show that the proposed method can efficiently handle large fingerprint code and trace colluders against averaging attacks.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques for extracting
phrases and stemming words. Then an ontology based conceptual
method will be used to annotate documents and expand the query.
To expand a query the spread activation algorithm is improved so
that the expansion can be done in various aspects. The annotated
documents and the expanded query will be processed to compute
the relevance degree exploiting statistical methods. The outstanding
features of our approach are (1) combining conceptual, statistical
and linguistic features of documents, (2) expanding the query with
its related concepts before comparing to documents, (3) extracting
and using both words and phrases to compute relevance degree, (4)
improving the spread activation algorithm to do the expansion based
on weighted combination of different conceptual relationships and
(5) allowing variable document vector dimensions. A ranking
system called ORank is developed to implement and test the
proposed model. The test results will be included at the end of the
paper.
Abstract: This study examined the effects of two dynamic
visualizations on 60 Malaysian primary school student-s performance
(time on task), retention and transference. The independent variables
in this study were the two dynamic visualizations, the video and the
animated instructions. The dependent variables were the gain score of
performance, retention and transference. The results showed that the
students in the animation group significantly outperformed the
students in the video group in retention. There were no significant
differences in terms of gain scores in the performance and
transference among the animation and the video groups, although the
scores were slightly higher in the animation group compared to the
video group. The conclusion of this study is that the animation
visualization is superior compared to the video in the retention for a
procedural task.
Abstract: In this communication a quantitative modeling
approach is applied to construct model for the exchange of gases
from open sewer channel to the atmosphere. The data for the
exchange of gases of the open sewer channel for the year January
1979 to December 2006 is utilized for the construction of the model.
The study reveals that stream flow of the open sewer channel
exchanges the toxic gases continuously with time varying scale. We
find that the quantitative modeling approach is more parsimonious
model for these exchanges. The usual diagnostic tests are applied for
the model adequacy. This model is beneficial for planner and
managerial bodies for the improvement of implemented policies to
overcome future environmental problems.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: The kinematics of manipulators is a central problem in the automatic control of robot manipulators. Theoretical background for the analysis of the 5 Dof Lynx-6 educational Robot Arm kinematics is presented in this paper. The kinematics problem is defined as the transformation from the Cartesian space to the joint space and vice versa. The Denavit-Harbenterg (D-H) model of representation is used to model robot links and joints in this study. Both forward and inverse kinematics solutions for this educational manipulator are presented, An effective method is suggested to decrease multiple solutions in inverse kinematics. A visual software package, named MSG, is also developed for testing Motional Characteristics of the Lynx-6 Robot arm. The kinematics solutions of the software package were found to be identical with the robot arm-s physical motional behaviors.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: In this work we present some matrix operators named
circulant operators and their action on square matrices. This study on
square matrices provides new insights into the structure of the space
of square matrices. Moreover it can be useful in various fields as in
agents networking on Grid or large-scale distributed self-organizing
grid systems.
Abstract: In this work, a radial basis function (RBF) neural network is developed for the identification of hyperbolic distributed parameter systems (DPSs). This empirical model is based only on process input-output data and used for the estimation of the controlled variables at specific locations, without the need of online solution of partial differential equations (PDEs). The nonlinear model that is obtained is suitably transformed to a nonlinear state space formulation that also takes into account the model mismatch. A stable robust control law is implemented for the attenuation of external disturbances. The proposed identification and control methodology is applied on a long duct, a common component of thermal systems, for a flow based control of temperature distribution. The closed loop performance is significantly improved in comparison to existing control methodologies.
Abstract: Effects of bio-nitrogen fertilizer (bio-N), as a partial
alternative to mineral-nitrogen fertilizer (mineral-N), on growth,
yield and yield quality of broccoli plants were investigated. Bio-N
was applied at 1, 2 or 3 doses in combination with 65% of the
recommended dose of mineral-N (bio-N1, bio-N2 or bio-N3 +
⅔mineral-N). However, 100% of the recommended dose of mineral-
N was applied as a control. Significant positive influences of the bio-
N3 + ⅔mineral-N treatment were observed on growth traits, leaf
contents of nitrogen, phosphorus, potassium, nitrate and nitrite, and
yield quality when compared to the other two combined treatments.
In contrast, there were no significant differences in these parameters
between the bio-N3 + ⅔mineral-N and the control treatments, except
for leaf contents of nitrate and nitrite. They showed lower contents in
the bio-N3 + ⅔mineral-N treatment than the control. Therefore, we
recommend using bio-N as a partial alternative to mineral-N for
healthy nutrition.
Abstract: The purpose of this research is to study motivation
factors and also to study factors relation to job performance to
compare motivation factors under the personal factor classification
such as gender, age, income, educational level, marital status, and
working duration; and to study the relationship between Motivation
Factors and Job Performance with job satisfactions. The sample
groups utilized in this research were 400 Suan Sunandha Rajabhat
University employees. This research is a quantitative research using
questionnaires as research instrument. The statistics applied for data
analysis including percentage, mean, and standard deviation. In
addition, the difference analysis was conducted by t value computing,
one-way analysis of variance and Pearson’s correlation coefficient
computing. The findings of the study results were as follows the
findings showed that the aspects of job promotion and salary were at
the moderate levels. Additionally, the findings also showed that the
motivations that affected the revenue branch chiefs’ job performance
were job security, job accomplishment, policy and management, job
promotion, and interpersonal relation.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoiler. The standard k-ε model is selected to numerically simulate the external flow field of the simplified Camry model with or without a rear-spoiler. Through an analysis of the simulation results, a new rear spoiler is designed and it shows a mild reduction of the vehicle aerodynamics drag. This leads to less vehicle fuel consumption on the road.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.